Question about 1991 Isuzu Trooper

1 Answer

How to collapse rear calipers

How to collapse rear brake calipers on a 1991 Isuzu Trooper 4wd?

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 107 Answers

If it has ratcheting calipers , you will need to clamp off brake line , open bleeder and turn in the piston counter clockwise with proper tool to get it back in , will need to bleed when done

Posted on Jun 27, 2010

Ad

1 Suggested Answer

6ya6ya

6ya staff

  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do u remove hubs on a 1992 Isuzu big horn


TO DO WHAT? not even the smallest hint on job or failure.>?
USA?
hubs, the rears have hubs to with disc brake option.rotor hubs.
I guess front hubs?.
guess 2, wheel bearing hubs, and not 4wd axle locking hub units.
doing what?
brakes, wheel bearings, axle damage. 4wd axle bearings what?
the pages are 2wd pages, and 4 wd pages, which is yours?
is this your first time DIY ever. ? or first time 4wd?
guess 3, 4wd, how am I guessing....


names
Acura SLX
Chevrolet Trooper
Isuzu Bighorn
Holden Jackaroo
Holden Monterey
Honda Horizon
HSV Jackaroo
Opel Monterey
Subaru Bighorn
Vauxhall Monterey
wow......
our usa book lists it as trooper only.
so ...

just B or B then A off? if you had b off, you'd see what?, a big nut.
that is locked to spindle shaft.
ill guess? wheel bearings are bad? (just in hub not spindle bearings bad... no matter this is first.)
so you do what. ? here are the steps.

that part"B" must be off first, see the bolts holding it, ?
B = auto locking hubs. or hub axle lockers.
26005769-b5pjo3cin0lhc1b54v4xlnuy-4-0.jpg you can see the caliber must come off, so, do so and tie them up.
  1. "Place the Transfer shift in the 2H position.
  2. Raise and support the front of the vehicle safely on jackstands. (rear tires chocked, and hand brake set hard)
  3. Remove the wheel and tire assembly.
  4. Loosen the hub to rotor retainer bolts.
  5. Remove the brake caliper mounting bolts and carefully remove the caliper (along with the brake pads) from the rotor. Do not disconnect the brake line. Secure the caliper out of the way with the flexible line still connected.
  6. Remove the hub nut using hub wrench J-29020-A or equivalent. ( special tool)
  7. Remove the hub cap assembly retainer bolts. Remove the spindle nut, washers, and other components. Remove the hub/rotor, being careful not to drop the outer wheel bearings. As the hub/rotor is pulled forward, the outer wheel bearings will often fall forward.
  8. Once the hub/rotor is removed, remove the retainer bolts securing the rotor and hub together. Inspect the hub and replace if needed."
  9. end removal. install is next... (alldata.com covers this)

Dec 13, 2015 | Isuzu Cars & Trucks

1 Answer

2000 isuzu trooper brakes? dont always release after stop


brake caliper sliders or pistons seized. (most common problem)

Mar 14, 2013 | 2000 Isuzu Trooper

2 Answers

Dragging rear disc brake


Your brake caliper on this tire is likely bad, but it could also be a problem with the emergency brake cable hanging up on this wheel.

Were you using the emergency brake before the problem happened? If so, I'd maybe look more at the cable.

Mar 30, 2010 | 1991 Isuzu Trooper

2 Answers

How to collapse rear calipers on mini cooper


Did you notice the brake fluid level in the master cylinder before you tried to collapse the calipers? You should see a rise in level as you collapse them (however far they did collapse). If you're not seeing any change in the level (it should fill up) you might have a plugged valve between the caliper and the master cylinder. Loosen the brake fluid line to the caliper and try collapsing it again. If still no go, start dismantling the caliper and look for bent, broken, stuck or mal-adjusted pieces.

Feb 07, 2010 | 2005 Mini Cooper

1 Answer

I have a 99 isuzu trooper (jackaroo) 3.5 liter 4wd with torque on demand my jssue is the check rear wheel's lights blinks green then red if I put it in 4wd the rear wheel light indicator gose green the...


sounds like a sensor - when did it start - if just cranked up one day and bam it is there - sounds like either a brake wear indicator issue - if they are connected in those - or a fluid level change in the rear end or transfer case - look for leaks and check the brake pads or shoes

Dec 26, 2009 | 1999 Isuzu Trooper

1 Answer

Are the trroper and Rodeo related?


Yes, they should be. The Rodeo and Trooper LS (3.2L) definitely have the same rear calipers.
All you need to do is punch in both models on napa or autozone.com, and ensure they list the same parts.

Jul 21, 2009 | 1997 Isuzu Trooper

1 Answer

THE DRIVER WHEEL BRAKES ON MY 94 TROOPER WILL NOT DISENGAGE


the brake caliper is frozen, this is usually caused by an extended trip to heat up brakes, followed by submerging caliper in or washing with lots of water

or hitting puddles at high speed while hot

Jun 03, 2009 | 1994 Isuzu Trooper

1 Answer

Brake job on 1994 isuzu trooper


are they drums on the rear? if not you can do this. on the caliper there should be 2 bolts holding it on. loosen one and pull the other out. lift the caliper up or down remove pads open the master cylinder so that you can compres the piston on the caliper. if you dont open the master sylinder cap it will be very tough. replace pads. tighten bolts nice and snug. then with car off pump brakes till tough. make sure you fill the master sylinder up that way no air gets in to it. if you do you gonna have to bleed the brakes. if that happens start at the passenger side rear then driver side rear then passenger front then driver front. please lemme know if you need help or if i helpd at all

Apr 24, 2009 | 1994 Isuzu Trooper

1 Answer

1995 isuzu trooper caliper removal


remove front wheel ,look at back of caliper and and look for teh two retaining bolts that hold the caliper to the support bracket.if not sure take it to a garage as any mistake could kill someone

Sep 01, 2008 | 1995 Isuzu Trooper

2 Answers

Rear brakes way too hot. replaced the pads and very difficult to turn in, in fact had to releive pressure at the hose to get it to go in at all. Is it possible that the master is at fault? I don't want to...


it seems to me like they are rubbing all the time when in use this has got to be due to the pistons in the calapers are sticking once brake is applied, i've had the same problem but that was on my motorbike.

Jul 25, 2008 | 1991 Isuzu Trooper

Not finding what you are looking for?
1991 Isuzu Trooper Logo

Related Topics:

267 people viewed this question

Ask a Question

Usually answered in minutes!

Top Isuzu Experts

Marvin
Marvin

Level 3 Expert

85222 Answers

Steve Hurc
Steve Hurc

Level 3 Expert

459 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22485 Answers

Are you an Isuzu Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...