At Fixya.com, our trusted experts are meticulously vetted and possess extensive experience in their respective fields. Backed by a community of knowledgeable professionals, our platform ensures that the solutions provided are thoroughly researched and validated.
Re: speedometer not working cable good from trany to
THE SPEEDOMETER CABLE GOOD AND SPEEDOMETER NOT WORKING.2 POSSIBLE CAUSES WHILE ITS NOT WORKING SPEEDOMETER GAUGE BROKEN OR SPEEDOMETER DRIVE GEAR IN EXTENSION HOUSING BROKEN.
- If you need clarification, ask it in the comment box above.
- Better answers use proper spelling and grammar.
- Provide details, support with references or personal experience.
Tell us some more! Your answer needs to include more details to help people.You can't post answers that contain an email address.Please enter a valid email address.The email address entered is already associated to an account.Login to postPlease use English characters only.
Tip: The max point reward for answering a question is 15.
Replacing the speedometer cable could be tricky as if it is not run properly could cause the cable to break inside the housing. The cable should be in a position without sharp curves and should be as straight as possible.
Go under the car and take off the speedo connection at the transmission. Try to pull out the inside cable to see if it is broken.
Pull your negative battery cable for 30 min see if it resets your sytem. Guages should jump up and drop back then work perfectly. Had to do this with my 2005 monte carlo
QU40221 19 Spline Outer Axle Shaft for 1977 to 1991 Chevy, GMC Corporate GM 10 Bolt Front Axle is a genuine original equipment outer axle stub shaft for all GM 10 Bolt front axles in 1977 to 1991 Chevy Blazers, GMC Jimmys, and Suburbans, plus Chevy, GMC 4x4 1/2 ton and 3/4 ton Pickups. The splined end on these new axle shafts has three snap ring grooves in three places so they are compatible with all types of automatic and manual lockout hubs plus all full-time solid splined drive gears.
Also available while supplies last: QU40221U Used Outer Axle Shaft with 3 snap ring grooves and QU40660UUsed Inner Axle Shafts with 2 snap ring grooves (QU40660U is not compatible with automatic locking hubs)
Hi, this is a pretty common problem on these Silverado instrument clusters. We can repair it for you or provide you with the parts to do it yourself. Click here to learn more about these silverado instrument cluster problems: Dr Speedometer Instrument Cluster Repair Speedometer Repair Guage...
the cable is broken unscrew it from the trany turn it by hand back or foward the spedo gauge on dash should move a little or you will be able to pull the broken cable out of the insert
The first thing to do would be to remove the cable at the trany and spin the inner part of the cable and see if speedometer moves a little, if it moves then you will know the cable is good and so is the speedometer and the problem is the gear in the trany, remove the small housing that the cable screws into amnd there you will see a gear, remove the clip and slide the gear off and replace it with a new one, you should be able to seee the gear teeth worn out,but is the speedo doesnt move when you turn the cable then the cabl may be bad, slide cable out by pulling it, and look for thee broken end. hope this helps.
you need a new speed sensor located on the gearbox with 2 size ten bolts holding it on and a 3 pin connection going into it! heres a pic http://www.hondacivicrepairs.com/views/honda-civic-speed-sensor.JPG
Well I would verify the trany speed gear is "ate up" first, theres only one 10mm bolt that holds it in place, sure the area around the speedo cable is very CLEAN before removing it any dirt in there would make things bad to say the least. If you pull the cable out the gear is attached to the cable if it looks good then put it back together and remove your cluster (speedo and other gauges inside) I suggest you pick up a repair manual at a big auto store on MK1-MK2 vdubs (82-92) to explain how to remove speedo cable from back of cluster its kinda of tricky getting your fingers back there and pressing it together to get it to release. Once out drive the car and see if that cable is turning from the inside if it is then its your speedo gauge that is faulty. Grab a cluster from a scrap yard, if that cable is NOT turning then the gearing inside the trany is messed up which would mean taking the trany apart to repair it. If that was the case you would be cheaper to replace the whole trany with a used one. Good luck
×