ODB2 CODE 1259 2002 HONDA ACCORD - 2002 Honda Accord

Question edited for clarity.
Question moved to model category from Miscellaneous.

Strange Japanese codes! Just run them through Google.

https://www.google.com/search?q=2009+Honda+Accord+4+cylinder.+83-13

Code 71 after SRS Reset - Honda Accord Forum

hondaaccordforum.com https://www.hondaaccordforum.com > forum > code-...
Oct 10, 2015 - The code 71-1 and 71-2 are for the driver's seat position sensor. 71-1 is for an open wire. 71-2 is for a short. The shop manual doesn't give .....

DTC 61-23: ABS Modulator-Control Unit Power Source Low Voltage. Attached is the diagnostic information. My experience has shown a bad battery can cause this code.
Mar 7, 2017

Honda Accord Code 61-23: Q&A on Dash Board Warning Light

..

Acura and Honda Radio COdE Retrieval and Unlock Tips ...

? 5:13
www.youtube.com/watch?v=tgfRmBo7Pu0
Nov 13, 2009 - Uploaded by Factory Car Stereo Repair Acura and Honda Radio COdE Retrieval and Unlock Tips .... mine is Honda Accord 93, click what button to active it? .... Radioreset code in 5 minutes for a 2001+ Honda CRV CR-V Accord Civic Pilot Element Odyssey Insight ...

I'll Assume you're talking about CEL codes, so here you go:


http://honda-tech.com/honda-accord-1990-2002-2/check-engine-light-codes-cel-diagnostic-trouble-codes-dtc-malfunction-indicator-light-mil-1490107/

Hi, according to autozone.com, the connector is under hood, driver side, side of strut tower, mounted on strut tower. The pic below, hoewever shows it mounted to the intake manifold. This is an OBD1 connector. You must use an OBD1 scanner to extract trouble codes or use the manual procedure pasted below. Please let me know if you need an explanation of the trouble codes (please specify your engine and trouble code) or have any other questions.



All models except the 1MZ-FE engine is equipped with OBD I till 1995.

1. Make sure the battery voltage is at least 11 volts.
2. Make sure the throttle valve is fully closed.
3. Place the gear shift lever in Neutral. Turn all accessories off.
4. The engine should be at normal operating temperature.
5. Using a jumper wire, connect terminals TE1 and E1 of the Data Link Connector 1 (DLC1).
6. Turn the ignition switch ON , but do not start the engine. Read the diagnostic code by the counting the number of flashes of the malfunction indicator lamp.
7. Codes will flash in numerical order. If no faults are stored, the lamp flashes continuously every 1 / 2 second. This is sometimes called the Normal or System Clear signal.
8. After the diagnosis check, turn the ignition OFF and remove the jumper wire.
9. Compare the codes found to the applicable diagnostic code chart. If necessary, refer to the individual component tests in this section. If the component tests are OK, test the wire harness and connectors for shorts, opens and poor connections.

hi there are 2 types for this vehicle, there is a 2 pin type and the normal ODB2 type 16 pin plug, these are normally found on the passenger side of the car under the dash near centre console..hope this helps

a 98 model should be odb2
lots of info online for the plug.
do a search for odb2 plug info.

Normal 0 false false false MicrosoftInternetExplorer4 /* Style Definitions */ table.MsoNormalTable {mso-style-name:"Table Normal"; mso-tstyle-rowband-size:0; mso-tstyle-colband-size:0; mso-style-noshow:yes; mso-style-parent:""; mso-padding-alt:0cm 5.4pt 0cm 5.4pt; mso-para-margin:0cm; mso-para-margin-bottom:.0001pt; mso-pagination:widow-orphan; font-size:10.0pt; font-family:"Times New Roman"; mso-ansi-language:#0400; mso-fareast-language:#0400; mso-bidi-language:#0400;} try https://radio-navicode.honda.com/



if the above suggestion is not successful ,then unfortunately the code will not be available for free (or cheap ) from anywhere on the Internet.

Main Dealer or a Decoding Service only

Contact HONDA with VIN# To get the radio code

Gotta have the serial number off the sticker on the top of the radio then call your local honda dealer, give them that serial number and they can give you your radio code.