I JUST WANT TO FIND THE PROPER ON LINE LINK TO THE SHOP MANUAL ASSEMBLY SECTION FOR THE 1992 735IL BMW FRONT PASSENGER INTERIOR DOOR PANEL

it's part of the door latch assembly , you have to take the door panel on the inside off .
Section 17-02: Lighting, Interior 1997 Town Car Workshop Manual REMOVAL AND INSTALLATION Procedure revision date: 05/16/2000 Switch, Courtesy Lamp
Removal

1. Remove front door trim panel (23942) and watershield. Refer to Section 01-05 .

1. Remove screw retaining lamp switch (13713) to front door latch (21812).

1. Disconnect lamp switch from body main wiring (14A005).

Installation

1. Follow removal procedure in reverse order.
   
   Interior Lamp Switch
   
   
   
   
   
   Item Part Number Description 1 14A005 Body Main Wiring 2 N610939-S36M Screw 3 14018 Door Ajar Switch 4 21812 Front Door Latch A - Tighten to 1.4-1.9 Nm (13-16 Lb-In)

Door Lock Cylinder LED
Refer to Section 01-14 .

My thought would be room lamp, 15 amp. Interior fuse box.

what is the issue? May not be the blend door motor. Big job.

The climate control assembly has three control knobs (18519):

• The airflow control or function selector knob controls vacuum and electrical applications.
• The temperature control knob, attached to the potentiometer, controls the position of the A/C electronic door actuator motor (19E616) mounted on heater air plenum chamber (18471).
• The blower motor control knob, attached to the heater blower motor switch (18578), provides four speeds of blower motor operation.

------------------------------------------------------------------------------------
A/C Electronic Door Actuator Motor Removal

1. Disconnect battery ground cable (14301). Refer to Section 14-01 .
   

1. Remove instrument panel (04320). Refer to Section 01-12 .
   

Instrument Panel Removal

1. Position wheels straight ahead.
   
2. Disconnect battery ground cable (14301). Refer to Section 14-01 .
   
3. Raise vehicle on hoist. Refer to Section 00-02 .
   
4. Remove RF wheel and tire assembly. Refer to Section 04-04 .
   
5. Remove retaining nut in radiator coolant recovery reservoir area.
   
6. Remove bolt retaining front fender apron (16054) to front fender (16005).
   
7. Position front fender splash shield out of the way.
   
8. Lower vehicle.
   
9. Tag and remove wiring connectors.
   
10. Remove retaining screw in parking brake control (2780). Remove parking brake control.
    
11. Remove screw retaining instrument panel steering column opening cover reinforcement (04502).
    
    
    
    
    
    
    
    
    
    
12. Remove steering column assembly. Refer to Section 11-04 .
    
13. Remove from the LH and RH cowl side trim panels (02345).
    
14. Remove lower cowl side trim panels.
    
15. Tag and disconnect wiring connectors in LH and RH cowls.
    
16. Remove ground wire assembly.
    
17. Remove retaining rivet in the passenger side of the instrument panel (04320).
    
18. Unsnap the instrument panel finish panel (04338), center and RH.
    
19. Unsnap the instrument panel finish panel, (LH).
    
20. Remove and disconnect the radio chassis (18806).
21. Remove retaining screw in the instrument panel finish panel.
    
22. Position the instrument panel finish panel out of the way.
    
23. Tag and disconnect the wiring connectors.
    
24. Remove retaining screw in the passenger side air bag module (044A74).
    
25. Disconnect the electrical connector to the passenger side air bag module.
    
26. Remove and disconnect the instrument panel upper finish panel (044A90).
    
27. Remove instrument panel to cowl brace retaining screw.
    
28. On Crown Victoria, Grand Marquis, remove screws retaining instrument panel finish panel (044D70) and remove instrument panel finish panel.
    
29. Remove retaining nut on the instrument LH and RH lower finish panel.
    
30. Remove instrument panel cowl brace (045D56).
    
31. Disconnect vacuum hose on the harness assembly.
    
32. Remove upper and lower screws retaining instrument panel finish panel to dash panel (01610).
    
    

1. Disconnect the A/C electronic door actuator motor electrical connector.
   
2. Remove four A/C electronic door actuator motor retaining screws.
   
3. Remove A/C electronic door actuator motor (19E616).
   
   

Sounds like the blend door actuator. It separates the driver and passenger side from getting air on the AZC system. Here are some instructions on replacing it:
The passenger side blend door actuator is used on all models equipped with Automatic Zone Control (AZC). This actuator is located on the front of the HVAC housing to the right of the floor panel transmission tunnel and cannot be removed from the passenger compartment without instrument panel or HVAC housing removal.

NOTE: This procedure is for AZC Systems (Passenger side only).

1. Disconnect and isolate the battery negative cable.
2. Remove the glove box door. See: Body and Frame\Interior Moulding / Trim
3. Remove the lower I/P glove box door surround panel.
4. Remove the dash assembly. See: Body and Frame\Interior Moulding / Trim\Dashboard / Instrument Panel\Service and Repair\Instrument Panel Assembly
5. Remove the HVAC assembly. See: Housing Assembly HVAC\Service and Repair
6. Unplug the wire harness connector from the blend door actuator.
7. Remove the 2 screws that secure the blend door actuator to the HVAC housing.
8. Remove the blend door actuator from the HVAC housing.

INSTALLATION - AZC (Passenger side only)

1. In stall the blend door actuator on the HVAC housing and tighten the two mounting screws to 2.2 Nm (20 in. lbs.).
2. Plug in the wire harness connector to the blend door actuator.
3. In stall the HVAC unit into the vehicle. See: Housing Assembly HVAC\Service and Repair
4. Install the instrument panel assembly into the vehicle. See: Body and Frame\Interior Moulding / Trim\Dashboard / Instrument Panel\Service and Repair\Instrument Panel Assembly
5. Evacuate the HVAC system.
6. Recharge the HVAC system.
7. Connect and the battery negative cable.

Hope it helps! If you need more, just send me an email at familyguy77351 at yah I wil be glad to finish helping you with more detail.

door panel must come off.

go here for villager help

http://groups.yahoo.com/group/villagerquest/

Section 01-05: Trim, Interior 1997 Villager Workshop Manual
REMOVAL AND INSTALLATION Trim Panel(s), Door
Front
Removal

1. Disconnect the battery ground cable (14301) if equipped with power locks or power windows.
   

1. CAUTION: Use care when removing the front door inside handle escutcheon (22620). Failure to do so can result in damage to the component.
   Carefully pry off the front door inside handle escutcheon by inserting a standard 1/4 inch screwdriver between the top rear portion of the front door inside handle escutcheon and the front door trim panel (23942).
   
   
   
   
   

1. If equipped with manual windows, slip a clean shop rag between the window regulator handle (23342) and the front door trim panel.
   

1. Pull the shop rag back and forth to release the window regulator handle clip.
   
   
   
   
   

1. Remove the three cover caps and front door trim panel screws.
   

1. Remove the one front door trim panel capped screw from the door pull handle.
   

1. If equipped with power windows, remove the door pull handle. Disconnect the electrical connectors.
   

1. Slide a flat-bladed tool behind each of the retainers and twist the tool to disengage the front door trim panel from the front door (20124).
   

1. Remove the front door trim panel.
   

Installation
To install, reverse the removal procedure. Body Side
Removal

1. Gently pry loose the body side door latch handle bezel and remove it.
   

1. Slide a suitable tool behind each of the retainers and twist the tool to disengage the body side door trim panel from the body side door (24622).
   
   
   
   
   

Installation
To install, reverse the removal procedure. Door Electrical Connections
Removal and Installation
Refer to Section 01-11 for Power Window, Section 01-09 for Power Mirror, or Section 01-14B for Power Locks. Watershield
Removal

1. Remove the Front Door Trim Panel . Refer to the removal procedure in this section.
   

1. Remove the front door watershield by carefully detaching it from the adhesive.
   

Installation

1. Install the front door watershield in the proper position and press firmly at the adhesive areas. If necessary, use additional adhesive to ensure an adequate seal.
   

1. Install the Front Door Trim Panel . Refer to the installation procedure in this section.
   

Review the Section-23-Body-ewj23S (page 34 and next).

Good luck (remember rated this help).

you either need a motor or motor and window regulator assembly.
SECTION 501-05: Interior Trim and Ornamentation 2002 Taurus/Sable Workshop Manual
REMOVAL AND INSTALLATION Front Door Trim Panel Removal and Installation

1. Disconnect the battery ground cable. For additional information, refer to Section 414-01 .

1. Remove the front door trim panel screws.

1. NOTE: To release the door trim panel two part pin-type retainers, first pull outward on the bottom of the door trim panel.
   Remove the front door trim panel.
   • Disconnect the electrical connectors.

--------------------------------------
SECTION 501-11: Glass, Frames and Mechanisms 2002 Taurus/Sable Workshop Manual
REMOVAL AND INSTALLATION Front Door Window Regulator And Motor
Special Tool(s) Heavy Duty Riveter
501-D011 (D80L-23200-A) or equivalent
Removal and Installation

1. Remove the front door window glass. For additional information, refer to Front Door Window Glass in this section.

1. Disconnect the front door window regulator motor electrical connector.

1. Remove the window regulator rivets.

-----------------------------
SECTION 501-11: Glass, Frames and Mechanisms 2002 Taurus/Sable Workshop Manual
REMOVAL AND INSTALLATION Door Window Regulator Motor Removal and Installation

1. Close the window.

1. Disconnect the battery ground cable. For additional information, refer to Section 414-01 .

1. Remove the door trim panel. For additional information, refer to Section 501-05 .

1. If equipped, remove the radio speaker.

1. Position the watershield aside.

1. Disconnect the door window regulator motor electrical connector.

1. Remove the bolts and the door window regulator motor.

---------------------------------------------------

probably need a new window regulator. ebay. 93 to 98 should fit.

Section 01-05: Trim, Interior 1998 Villager Workshop Manual
REMOVAL AND INSTALLATION Trim Panel(s), Door Front
Removal

1. Disconnect the battery ground cable (14301) if equipped with power locks or power windows.
   

1. CAUTION: Use care when removing the front door inside handle escutcheon (22620). Failure to do so can result in damage to the component.
   Carefully pry off the front door inside handle escutcheon by inserting a standard 1/4 inch screwdriver between the top rear portion of the front door inside handle escutcheon and the front door trim panel (23942) .
   
   
   
   
   

1. If equipped with manual windows, slip a clean shop rag between the window regulator handle (23342) and the front door trim panel .
   

1. Pull the shop rag back and forth to release the window regulator handle clip.
   
   
   
   
   

1. Remove the three cover caps and front door trim panel screws.
   

1. Remove the one front door trim panel capped screws from the door pull handle.
   

1. If equipped with power windows, remove the door pull handle. Disconnect the electrical connectors.
   

1. Slide a flat-bladed tool behind each of the retainers and twist the tool to disengage the front door trim panel from the front door (20124) .
   

1. Remove the front door trim panel.
   

Installation
To install, reverse the removal procedure.
---------------------------------------------------------
Window Regulator, Power Front Door
Removal

1. Disconnect the battery ground cable (14301) .
   

1. Remove the front door window glass (21410) . Refer to the front door window glass removal procedure in this section.
   

1. Remove the two front door brace bolts and the front door brace.
   
   
   
   
   

1. Disconnect the front window regulator electric drive electrical connector.
   

1. Remove the four front door window glass regulator track bolts.
   
   
   
   
   

1. Remove the three front window regulator electric drive bolts.
   

1. Remove the front door window glass regulator track and the front window regulator electric drive (23394) as an assembly through the opening in the front door (20124) .
   

Installation

1. Install the front door window glass regulator track and the front window regulator electric drive as an assembly through the opening in the front door .
   

1. Install the three front window regulator electric drive bolts. Tighten the front window regulator electric drive bolts securely.
   

1. Install the four front door window glass regulator track bolts. Tighten the front door window glass regulator track bolts securely.
   

does it act the same whether you use the driver door switch or the passenger door switch? Please rate as fixya if this helps. thanks

here's repair procedure

Window Regulator, Front Door, Explorer Removal
WARNING: IF THE REGULATOR COUNTERBALANCE SPRING MUST BE REMOVED OR REPLACED FOR ANY REASON, MAKE SURE THAT THE REGULATOR ARMS ARE IN A FIXED POSITION PRIOR TO REMOVAL TO PREVENT POSSIBLE INJURY DURING C-SPRING UNWIND.

1. Remove front door trim panel and front door trim shield . Refer to Section 01-05B .

Trim Panel, Front Door, Explorer Hi-Series, Two-Door and Four-Door Removal and Installation

1. Remove the two screws retaining the front door trim panel (23942) located above the window regulator handle (23342) . Also remove one screw in the upper front portion of front door trim panel .

1. Remove inside door handle cup (22634) at the window regulator handle using a screwdriver or sharp object. Retention nibs will flex for easy removal.

1. To remove window regulator control switch (14529) and outside rear view mirror control (17B676) , use notch located at lower end of outside rear view mirror control using a screwdriver to lift and remove.

1. Remove outside rear view mirror control from front door trim panel pulling wire harness from inside of front door trim panel .

1. From bottom of outside rear view mirror control, remove two screws and disconnect connector from switches. NOTE: Do not pull on the front door trim panel to remove clips from the inner panel holes.
   

1. At each plastic clip location, pry the front door trim panel away from the door inner panel using the front door trim panel removing tool from Rotunda Moulding Trim Kit 107-00401 or equivalent. NOTE: Pay special attention to the cut-out in the door trim panel for the door handle, so that it clears the handle during removal without breakage.
   

1. When wiring and disengagement of trim clips is completed, it is recommended that to remove panel, lift slightly to remove flange at the top of door trim panel from trough in the glass weatherstrip.

1. Disconnect socket and bulb from illuminated interior lamp (13776) before total removal of front door trim panel. For installation, follow removal procedures in reverse order. Replace any bent, damaged or missing plastic clips on the front door trim panel to the front door trim panel , firmly loading clips into slots provided on front door trim panel .
   
   Trim Panel, Front Door, Explorer Hi-Series Four-Door
   
   

1. Remove inside door belt weatherstrip and glass stabilizer.

1. Remove front door window glass as described in this section.

1. Remove two nut and washer assemblies attaching the equalizer bracket.

1. Remove three rivets (manual) or four rivets (power) attaching the regulator base plate to front door trim panel finish panel (23712) .

1. Remove window regulator electric drive and front door window channel bracket from vehicle.

1. Working on a bench, carefully bend tab flat to remove arm slides from front door window channel bracket .

1. Install new window regulator electric drive arm plastic guides into front door window channel bracket and bend tab back to 90 degrees. Use care not to break tab; if tab is cracked or broken, replace front door window channel bracket . Make sure rubber bumper is installed properly on new front door window channel bracket , if replacement is made.
   
   
   
   

Installation
NOTE: The front door window channel bracket and window regulator electric drive are installed into the vehicle as one assembly. The front door window channel bracket may be disassembled from the window regulator electric drive as described in Steps 7 and 8 of Window Regulator, Removal.

1. Install front door trim panel finish panel with preassembled glass bracket into vehicle. Set the regulator base plate to window regulator electric drive using base plate locator tab as a guide.

1. Install three (manual) or four (power) rivets (385189-S100) to attach regulator to front door trim panel finish panel . Two 1/4-20 x 1-inch bolts and two 1/4-20 nut and washer assemblies may be used as alternates for glass retention. However, torque must not exceed 4-7 Nm (3-5 ft-lb). Equivalent metric retainers may be used.
   

1. Install equalizer bracket.

1. Install inside door belt weatherstrip and glass stabilizer.

1. Lower regulator arms to access holes in front door trim panel finish panel . Install front door window glass as outlined.

1. Adjust glass to ensure proper alignment with glass run. Cycle glass for smooth operation.

1. Install front door trim panel and front door trim shield . Refer to Section 01-05B .

was the damage to the front was closer to the passenger side? if sow when the snow plow hit the frunt it cosed the pasinger door to get jamed on it self wich will not allow the door to open. look and see if the passenger side lines mach up with the body and the door. damege to the front can move all the way to the back of a car you need to take the car to a body shop and have a qout done for you