1998 Plymouth Breeze Logo
Anonymous Posted on Jun 05, 2010

I just had the belts changed on my 1998 Plymouth Breeze and the power steering pump and bracket changed. I have noticed lately that there is a squealing noise coming from under the hood. Could my belts need changed already or is this a common problem?

  • toneman2121
    toneman2121 Jun 06, 2010

    if your power steering pump is drivien by an individual belt, it may be loose. check the tension of the belt. i would say 1/4" to 1/2" deflection at the point midway between the longest section of the belt between the pulleys. you should consult the shop that did the repair

  • Anonymous Jun 06, 2010

    I am not sure. I took it for a oil change and was told that 1 belt was half off pulley and 1 had huge chunks out of it and they would have to pull the motor to change the belts. So I took it to a friend of a friend that a mechanic on the side. I was told that the belts needed replacing and he did that but when he tried starting it the power steering pump kicked the belts off again and pushed the pulleys out of line. He said he replaced the power steering pump and bracket. I have had it back for over a month and just noticed the squealing a week ago. the guy who fixed it is out of town so can't reach him right now. Am I going to do damage if I keep driving it? I have always have new vehicles so this beater stuff is all new to me. Thanks for any help

×

3 Answers

Anonymous

Level 3:

An expert who has achieved level 3 by getting 1000 points

All-Star:

An expert that got 10 achievements.

MVP:

An expert that got 5 achievements.

President:

An expert whose answer got voted for 500 times.

  • Master 678 Answers
  • Posted on Jun 06, 2010
Anonymous
Master
Level 3:

An expert who has achieved level 3 by getting 1000 points

All-Star:

An expert that got 10 achievements.

MVP:

An expert that got 5 achievements.

President:

An expert whose answer got voted for 500 times.

Joined: Apr 11, 2009
Answers
678
Questions
0
Helped
371628
Points
2431

The belts shouldn't need to be changed again. There are a number of reasons why the belt could be squealing. There could be too little tension on the belt, either adjusted incorrectly or a bad automatic tensioner. Fluids could be leaking onto the belt. Pulleys could be misaligned or it's possible that the wrong size belt was used. I would bring it back to whomever changed the belts and explain what is occurring and under what conditions.

  • Anonymous Jun 06, 2010

    Thanks I will get in contact with the person who changed them. They did change the pulleys too I think. So I will get it rechecked.

×

Anonymous

Level 3:

An expert who has achieved level 3 by getting 1000 points

Superstar:

An expert that got 20 achievements.

All-Star:

An expert that got 10 achievements.

MVP:

An expert that got 5 achievements.

  • Master 2,317 Answers
  • Posted on Jun 06, 2010
Anonymous
Master
Level 3:

An expert who has achieved level 3 by getting 1000 points

Superstar:

An expert that got 20 achievements.

All-Star:

An expert that got 10 achievements.

MVP:

An expert that got 5 achievements.

Joined: Mar 05, 2010
Answers
2317
Questions
1
Helped
787579
Points
7079

The belts may need to be retightened. New belts will stretch a bit after they are first installed.

Ad

Anonymous

Level 3:

An expert who has achieved level 3 by getting 1000 points

All-Star:

An expert that got 10 achievements.

MVP:

An expert that got 5 achievements.

President:

An expert whose answer got voted for 500 times.

  • Master 834 Answers
  • Posted on Jun 06, 2010
Anonymous
Master
Level 3:

An expert who has achieved level 3 by getting 1000 points

All-Star:

An expert that got 10 achievements.

MVP:

An expert that got 5 achievements.

President:

An expert whose answer got voted for 500 times.

Joined: Apr 15, 2010
Answers
834
Questions
0
Helped
899229
Points
3735

Most likely a drive belt tensioner bearing or idler pulley bearing is going out and that really should have been know at the time the old belts were removed, but if one of the belts has loosened up, either because of an adjustment hold down bolt not being tight enough to hold the belt adjustment, or sometimes a new belt will stretch after it has been ran on the engine and it will require that the belt be re-tightened, and your mechanic (well, any good mechanic) should not charge you to re-tighten the belt.

If the power steering bracket bolts have come loose and is causing the belt to be slack, then that is most certainly the mechanics fault and there should be no charge for that either.

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

0helpful
2answers

How do i replace the other belt on 2000 plymouth breeze

That belt would be for power steering,accessed from below would be easier, the pump bracket is the adjustment for it and the serpentine belt would need to be off to remove and install the other one.
2helpful
1answer

How to install a power steering pump for a 1997 chrysler seabring conv

Chrysler Cirrus/Stratus/Sebring/Avenger/Breeze 1995-1998
Power Steering Pump - REMOVAL & INSTALLATION

Cirrus, Stratus, Sebring Convertible and Breeze
(see Figures 1, 2, 3 and 4)
  1. Disconnect the negative battery cable from the left strut tower. The ground cable is equipped with an insulator grommet, which should be placed on the stud to prevent the negative battery cable from accidentally grounding.
  2. Siphon as much power steering fluid out of the reservoir as possible.
  3. Raise and safely support the vehicle.
  4. Remove the right front tire and wheel assembly.
  5. Remove the splash shield from the right front wheel well.
c901554.jpg

Fig. 1: Power steering pressure hose attachment to the pump-with Variable-Assist steering

8786c07.jpg

Fig. 2: Power steering pressure hose attachment to the pump-without Variable-Assist steering
  1. Disconnect the power steering pressure hose from the pump.
  2. Remove the hose connection on the power steering pump.
e7733b2.jpg

Fig. 3: Typical power steering pump front bracket attachment
  1. Remove the power steering adjusting bolt.
  2. Remove the power steering pump rear attaching bolt.
  3. If so equipped, remove the Anti-lock Brake System (ABS) hydraulic control unit heat shield.
  4. Remove the wheel speed sensor retainer bracket from the right inner fender.
  5. Remove the wheel speed sensor sealing grommet from the right inner fender.
  6. Disconnect the speed sensor wiring.
  7. Push the wiring through the hole in the inner fender.
If not equipped with anti-lock brakes, the hole will just have a sealing plug.
  1. Remove the bolt attaching the power steering front bracket to the mounting bracket. Access to the bolt is gained through the hole for the speed sensor wiring.
  2. Remove the power steering pump drive belt.
  3. Remove the power steering pump and the front bracket as an assembly.
To install:
  1. Install the power steering pump and bracket.
  2. Reinstall the bolt at the adjusting slot, but do not tighten.
  3. Reinstall the bolt mounting the power steering pump to the rear mounting bracket, but do not tighten.
  4. Reinstall the power steering pump top bolt, but do not tighten.
  5. Reconnect the power steering hoses.
b72b14a.jpg

Fig. 4: Install a new O-ring gasket on the hose fitting
Use a new O-ring when reinstalling the power steering pressure hose.
  1. Reinstall the drive belt.
  2. Adjust the drive belt and tighten the power steering pump bolts to 40 ft. lbs. (54 Nm).
  3. Reinstall the splash shield.
  4. Reinstall the tire and wheel assembly.
  5. Lower the vehicle.
  6. Reconnect the negative battery cable.
  7. Refill the reservoir and bleed the power steering system.


Sebring Coupe and Avenger
  1. Disconnect the negative battery cable.
  2. Remove (drain, suction pump, etc.) as much power steering fluid as possible.
  3. Disconnect the return fluid line. Remove the reservoir cap and allow the return line to drain the fluid from the reservoir. If the fluid is contaminated, disconnect the ignition high tension cable and crank the engine several times to drain the fluid from the gearbox.
Cover any components located underneath the power steering pump with a shop towel to protect them from damage due to power steering fluid spillage. For example, the A/C compressor or alternator, depending on vehicle and engine, is below the power steering pump, so cover the A/C compressor or alternator with a shop towel before removing any hoses.
  1. Loosen (but do not remove) the power steering pump mounting bolts and remove the drive belt.
  2. Remove the pressure switch connector from the side of the pump.
  3. Disconnect the pressure line.
  4. Unbolt and remove the pump from the mounting bracket.
To install:
  1. Clean all parts well. Inspect the pump pulley for cracks. Check the hoses carefully for cracks or signs of weakness.
  2. Install the pump, wrap the belt around the pulley and lightly tighten the mounting bolts.
  3. Replace the O-rings and connect the pressure line. Connect the pressure line so the notch in the fitting aligns and contacts the pump's guide bracket. Tighten the fitting to 13 ft. lbs. (18 Nm).
  4. Connect the return line and secure with the clamp.
  5. Fasten the pressure switch connector.
  6. Adjust the power steering belt for proper tension and tighten the adjusting bolts.
Use only MOPAR ATF PLUS automatic transmission fluid type 7176, ATF+3 automatic transmission fluid, or equivalent, in the power steering system of Sebring coupe and Avenger models.
  1. Refill the reservoir and bleed the power steering system.

Hope this help to solve it (remember comment and rated this). TY for using Fixya.
1helpful
2answers

Power steering

I would check the power steering belt, next the fluid and go from there!
1helpful
1answer

1998 plymouth breeze is hard to steer. The power steering fluid is fine.

I would expect teither the power steering pump or the steering rack has failed. The good fluid in the unit is just not being put to use.
I hope this may have helped,
Tom
2helpful
2answers

How do I replace the serpentine belt on my 2000 Plymouth Breeze 2.4l engine?

the tensioner is on the alternator there is usually a cover over it you need to loosen the 2 screws on the alternator and turn the "adjuster" screw till the belt is loose enough to come off note the whay it is run then install and tighten the new belt it must be very tight or it will slip
1helpful
1answer

Steering is hard

the steering rack and pinion unit is failing, that is why you are getting the symptoms u have.
0helpful
1answer

How do I change the serpentine belt on a 1998 Plymouth Breeze?

look around the power steering pump, (Under or maybe behind) you should see a belt tensioner, loosen it and any other brackets close to that have a sliding point, once loose, the belt should slip right6 off, pay close attichion to the way it comes off, you don't wanna put it back on backwards, or your water pump will run in the wrong direction and cause it to over heat
1helpful
1answer

1998 plymouth Breeze

Timing belt has nothing to do with fuel issue. If you're only running on 2 cylinders...you need to find out if spark is missing from those cylinders. Also possible that when the timing belt was replaced, it was not timed properly which can bend a valve, causing rough running.
Not finding what you are looking for?

275 views

Ask a Question

Usually answered in minutes!

Top Plymouth Experts

ZJ Limited
ZJ Limited

Level 3 Expert

17989 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6988 Answers

Thomas Perkins
Thomas Perkins

Level 3 Expert

15088 Answers

Are you a Plymouth Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...