Passenger door panel removal Saturn L300 - 2006 Saturn L300

SOURCE: 2001 tahoe door panel

THE COUTESY LAMP IS HOT DUE TO THE DOOR BEING OPEN WHILE THIS PROCEDURE IS DONE!!!! First: Remove the triangle panel at the top of the door (behind the mirror). This is held in with two metal clips about half way down the panel. Do not pry at the bottom as there are two tabs that slide in to keep the module in place. I pulled the top of the triangle out by hand then could see the clips and used a straight screw driver to carefully pry from under the triangle panel so as not to scar the visible part after re-assembly. Once these two clips are disengaged the triangle should pull straight up and be free. Second: Carefully pry out the door lock insert. There are no significant tabs to worry about here. Again a straight screw driver and care should not leave any scars. The lock insert has no mechanical connection but simply is used to slide the lock rod. Re-installing you will need to align the slot for the rod in the lock or unlock position depending on the rod position. Third: Carefully pry out the insert that is located at the door handle. Start at the rear of the insert as this is where the clips are located and once the rear is out pull open the door handle and pull the insert to the rear so as not to break off the two front tabs. You will find two small screws (mine were black). One near the front and one at the rear of the door handle module. Both are 7 mm and are the only ones that need to be remove in the process. (I understand some door panels have an other screw at the very bottom of the door as well; guess you'll have to check you door. Fourth: Pry up the control panel for the automatic windows and unplug the wires. Here again start from the rear and once the rear is free pull the module to the rear and it should come free. There are tabs at the front that you do not want to break off. To unplug the wires - First remove the clips (mine were blue) that hold the plug in place. There is also a push catch on the plug that must be depressed to release the plug from the control panel. Fifth: My door had no push in 'buttons' or clips to hold the door panel in place. It simply lifted up and became free with the exception of the numerous wires attached to things like the speakers, the remote mirrow and courtesy light. Unplug these wires by first taking off any retaining clips (usually blue) and then unplug the wires. The courtesy light pulls straight out (toward the front) and watch your fingers as this is one hot little bulb. The door panel can then be totally removed and set aside. You may find it easier to remove the courtesy light lens by prying out the rear first and then pulling it toward the back of the door so as not to break the two front clips. I found it easier to do this and then install the bulb in the lens and then install the lens back in place. Six: I'm sure I don't need to say it but here goes - ' reverse the procedure to re-assemble'. Remember to poke the courtesy light wire out the hole and re-connect the remote mirror and speaker wires before the door is put in place. The wires to the window and electronic lock module can be installed after the door is back in place. Working by myself made the door difficult to handle during re-installation so I took a 'light' bungy cord and placed some protection over the top of the door and hooked the bungy into the opening were the door handle was to come through. This allowed me to steady the door and do the electrical connections as required. PS - we were replacing the power window motor and were able to 'force' the cable into the gears of the new motor by turning the motor and this saved a lot of further disassembly. The contacts on the new motor were reversed so I removed the pins from the plug going into the motor and reversed them - presto.

SOURCE: Instrument panel lights don't work on a 2001

try first your dimmer switch and second fuses
look your manuel for locations

gl G

SOURCE: remove door panel

Disconnect your negative battery cable. Locate and remove the screws that hold your interior door handles in place (they may be hidden by snap in, or snap on clips). Remove the interior door handles, then disconnect the wire clips to the switches. Your panel is held in place by snap in clips; use a small pry bar to pull them from the door (try to get as close to, or directly under the clips to prevent them from tearing out of the door panel). Once the clips are pulled, pull the panel upward to remove it from the door.
Install in reverse.

SOURCE: How do I remove the filter on my saturn l300, all it wants to do is turn, but not come off

This may sound stupid, but I will ask anyway.... did you "pull" on it after you loosened it? Been there...

SOURCE: How do I remove mt right front door panel and

A saturn is not like other cars you have to remove the outside door panel to get inside the door it has screws holding it on