Engine service light

Reset oil service light Honda Pilot. From years: 2003, 2004, 2005, 2006, 2007, 2008, 2009, 2010, 2011, 2012.
How do you reset oil service light Honda Pilot. From years: 2003, 2004, 2005.

1. Turn off the engine. Press and hold the SELECT/RESET button in the instrument panel and turn the ignition switch to run (one position before starting).
2. Hold the button for at least 10 seconds, until the indicator resets.
3. Turn the ignition off and then start the engine to verify the indicator has been reset.

How to reset oil service light Honda Pilot. From years: 2006, 2007, 2008, 2009, 2010, 2011, 2012.
Resetting the Engine Oil Life Display if maintenance service is done by someone other than your dealer, reset the maintenance minder as
follows:

1. Turn the ignition switch to the ON (II) position.
2. Press the select/reset knob repeatedly until the engine oil life is displayed.
3. Press the select/reset knob for about 10 seconds. The engine oil life and the maintenance item code(s) will blink.
4. Press the select/reset knob for another 5 seconds. The maintenance item code(s) will disappear, and the engine oil life will reset to 100.

All information is taken from the Honda Pilot owners manual.

How to Reset the Change Oil Light

After changing the engine oil, the system must be reset.

With the ignition key to ON, push the RESET button

located in the driver's side instrument panel fuse block. The

CHANGE OIL light will start to flash, press and hold the

RESET button again. The reset is complete when you hear
the chimes sound and the CHANGE OIL light goes out.

there is no light for emissions testing on this vehicle. there is a ses light that can come on, indicationg a problem with the engine or transmission electronic system. this will require a scan tool to pull trouble codes. there is another light called oil life monitoring that needs to be reset after oil changes, which I suspect is what you are seeing. here is a picture of the light and the instructions for resetting.,

The Engine Oil Life System calculates when to change your engine oil and filter based on vehicle use. Anytime your oil is changed, reset the system so it can calculate when the next oil change is required. If a situation occurs where you change your oil prior to a CHANGE OIL SOON message being turned on, reset the system.
After changing the engine oil, the system must be reset as follows:

1. Turn the ignition to RUN, with the engine OFF.
2. Press the information and reset buttons on the Driver Information Center (DIC) at the same time to enter the personalization menu.
3. Press the information button to scroll through the available personalization menu modes until the DIC display shows OIL LIFE RESET.
4. Press and hold the reset button until the DIC display shows ACKNOWLEDGED. This will tell you the system has been reset.
5. Turn the key to LOCK.

If the CHANGE ENGINE OIL message comes back on when you start the vehicle, the Engine Oil Life System has not reset. Repeat the reset procedure.

FIRST press and release the setup button to display oil life= xxx
then press and hold the reset button for about 2 sec it should then display oil life set to 100%
--------------------------------
Just pressing the reset button when the change oil light comes on while driving will not reset the computer

TURN THE IGNITION KEY TO RUN WITH THE ENGINE OFF.FULLY PRESS AND RELEASE THE ACCELERATOR PEDAL THREE TIMES WITH IN FIVE SECONDS.YOU HAVE TO DO THIS MORE THAN ONE TIME.ITS NOT GOING TO RESET FIRST TRY BUT DO THIS PROCEDURE.UNTIL THE CHANGE ENGINE OIL LIGHT WILL FLASH WHILE THE SYSTEM IS RESETTING.TURN THE KEY TO OFF.WAIT A FEW SECONDS.START CAR UP TO SEE IF CHANGE OIL LIGHT COME BACK ON.IF YES YOU HAVE TO TRY THE RESET PROCEDURE AGAIN.

Press setup on message center,
press select for system check,
At oil life, press reset

bad to worn out oil pump or excessive oil passage clearances that allowing more oil to pass thru them at a lower pressure due to the bigger opening. It can be a sign of an emminant engine failure due to oil starvation.

Is it the "oil change req." light? Your owners manual will have the process for reseting the oil change light.
If it is "service engine soon" light, the vehicle will need to be scanned with a professional scanner.

Hi to reset the oil life monitor
turn the key on engine off
push the gas pedal to the floor 3 TIMES WITH IN 5 SECONDS
the light will flash then go out

THIS SHOULD BE IT.
How do I reset the Engine Oil life monitor and how does it work? TO reset To reset the Engine Oil Life monitor do the following:
Reset Oil life in NAV/DIC by (with car running) going to INFO>Oil Life>RESET
Press and HOLD until XXX turns to 100%
How does it work? The oil life monitor is a pretty sophisticated algorithm.

GM "The GM Oil Life System will automatically adjust the oil change interval based on engine characteristics, driving habits and the climate in which the vehicle is operated."