Reverse lights only work sometimes on isuzu wizzard

Question 1

0helpful

1answer

4wd switch stays on

sometimes after using four wheel drive the light stays on you can put in reverse and it usually goes out if not the sensor maybe bad its located on the front axel mine had a broke wire

Apr 18, 2014 • 2004 Isuzu Rodeo

1helpful

1answer

Turn signals reverse lighs dont work need a wire diagram for this 1997 izuzu rdeo 4x4

Reverse light are operated by the range selector switch on the side of transmission aka. gear selector lever. A problem with the t/s lights would be in the turn signal combo switch.

Jan 11, 2011 • 1997 Isuzu Rodeo

0helpful

1answer

Back up lights won't work on 2004 Isuzu Rodeo. Bulbs and fuses are all good.

check the reverse switch which is connected to the back of transmission. it may be disconnected or have a broken switch.

Jan 05, 2011 • 2004 Isuzu Rodeo

0helpful

1answer

I own an Isuzu Wizzard (1998, diesel, automatic, fuel injection). One morning I started the car and I heard a slow, heavy stuttering. The gas pedal only reacted after 30 seconds. When driving, the car...

these are diagnostic charts that the dealer used back then hope it helps

Dec 13, 2010 • 1998 Isuzu Rodeo

0helpful

1answer

I have a 2003 isuzu rodeo. Sometimes it is hard to put into reverse. I can usually get it to work in 1 or 2 tries. the abs light came on a couple of times. what could make this happen?

I do not think shifting gears ,putting your car in reverse has nothing to do whit whit the abs to come on and off ,my isuzu rodeo did the same thing and it was a dirty sensor ABS on front wheels , There is a ring on the inside of the front disc's that works together with the ABS sensor to send information to the car computer when braking ,and must have a distance of about 1/8 of an inch between ring and sensor ,,they must not touch ,what happens is that over time dirt starts to build between sensor and ring ,and ring and sensor begin to touch ,and if they do touch ABS light will start be on and off while driving ,,most of the time the problem is the sensor and not necessarly a bad sensor ,,only a durty sensor and dirty ring ,a broken or loose wire also will activate the ABS light ,,,and about car hard to put into reverse ,you'll probably need a new clutch ,,good luck

Sep 18, 2010 • 2003 Isuzu Rodeo

0helpful

1answer

2004 isuzu rodeo check engine light stays on and reduced power light goes on and off but when on car looses speed. When reduced power light goes off, vehicle lunges forward and runs fine. My mechanic and...

I tried the DIY service and repair manuals from a website and it actually helped me repair transmission problem in my jcb 3cx site-master. it wont move forward or reverse, engine is good both solenoids for
forward and reverse work.
I don't have much technical knowledge but I just followed it step-wise, and works perfect! got it from www.reliable-store.com

Feb 25, 2018 • 2004 Isuzu Rodeo

0helpful

2answers

Check trans light on....no power

My brake lights are out, the back, reverse, and head lights all work. My steering is fine as well as my brakes. But the warning lights for brake and ABS light up on my dash board

Feb 17, 2010 • 1992 Isuzu Trooper

0helpful

1answer

1995 Isuzu Rodeo 4X4 3.2 5 speed manual, reverse lights on in 1st

the wiring on the gear box is connected to switches wrong, there bullet head connectors red to red wiring and blue to blue from switch to loom is correct
both wires on one switch are red connect these to the 2 red wires one has colour trace on it also. the other switch blue wires to blue wire on loom with possibly another colour wire but they are together. you cant go wrong the connectors are male on one wire and female on the other on each switch(detent switch)

Nov 22, 2009 • Isuzu Rodeo Cars & Trucks

8helpful

2answers

Hi I HAVE A ISUZU WIZZARD 3.0 WITH 4jx1 engine,it hard to started,diesel knock when it idle,engine light stay on with a code p10193 or p1393,already replace fuel filter,engine oil,train and renew a diesel...

Hi, you problem is the rail oil pressure sensor having a high voltage input - P0193 code set . This will also cause your faults .
Change the sensor which is under the cam cover and the smaller of the two there and it will run ok .
You need the sensor set up on a tech II after fitting to run at its best.

Oct 02, 2009 • Isuzu Trooper Cars & Trucks

0helpful

1answer

My 2000 isuzu trooper reverse lights always stay on no matter what gear I am in. I need to know where to find the reverse light switch.

usually only 2 places it can be,,,under the car near the gear shift.....or under the centere consol inside the car, where the gear shift is, need to remove part of the centre consol to get to it

Jul 30, 2009 • 2000 Isuzu Trooper

Question 2

Anonymous

Master 642 Answers
Posted on May 31, 2010

Anonymous

Master

Joined: Dec 09, 2009

Answers

642

Questions

0

Helped

293830

Points

1939

Manual gearbox: check on right hand side of gearbox. There's an electrical switch(looks like large nut nut) with 2 wires coming out of it These wires have connectors toward the top of the gearbox, diconnect them.
The wires that this switch was connected to, conect them to each other. ie the reverse light switch has been bypassed. Put the vehicle in reverse. Turn on the ignition. DO NOT START. Check the reverse lights. If on the switch is faulty and needs to be replaced. If not measure the voltage across each of the wires and a good earth point. (Gearbox casing will do fine. ) One of the wires should read < 12V.
If 12V then

Globes are faulty(Replace)

wiring to the globes are faulty - unlikely -(This can be repaired by simply running a new wire to the globes)

If no 12V then the wiring to the fusebox is faulty. A quick fix is to run a new wire from the fusebox to the switch(Connect to fuse C-3, indicated as "turn, back")

Related Topics:

Trustworthy Expert Solutions

Reverse lights only work sometimes on isuzu wizzard

1 Answer

Anonymous

Add Your Answer

Attachments: Added items

Related Questions:

4wd switch stays on

Turn signals reverse lighs dont work need a wire diagram for this 1997 izuzu rdeo 4x4

Back up lights won't work on 2004 Isuzu Rodeo. Bulbs and fuses are all good.

I own an Isuzu Wizzard (1998, diesel, automatic, fuel injection). One morning I started the car and I heard a slow, heavy stuttering. The gas pedal only reacted after 30 seconds. When driving, the car...

I have a 2003 isuzu rodeo. Sometimes it is hard to put into reverse. I can usually get it to work in 1 or 2 tries. the abs light came on a couple of times. what could make this happen?

2004 isuzu rodeo check engine light stays on and reduced power light goes on and off but when on car looses speed. When reduced power light goes off, vehicle lunges forward and runs fine. My mechanic and...

Check trans light on....no power

1995 Isuzu Rodeo 4X4 3.2 5 speed manual, reverse lights on in 1st

Hi I HAVE A ISUZU WIZZARD 3.0 WITH 4jx1 engine,it hard to started,diesel knock when it idle,engine light stay on with a code p10193 or p1393,already replace fuel filter,engine oil,train and renew a diesel...

My 2000 isuzu trooper reverse lights always stay on no matter what gear I am in. I need to know where to find the reverse light switch.

Not finding what you are looking for?

1998 Trooper

4wd switch stays on

Ask a Question

Check Out the Latest Top Trucks Report!

Top Isuzu Experts

ZJ Limited

Thomas Perkins

Ronny Bennett Sr.

Are you an Isuzu Expert? Answer questions, earn points and help others

Manuals & User Guides

Related Topics:

Trustworthy Expert Solutions

Reverse lights only work sometimes on isuzu wizzard

1 Answer

Anonymous

Add Your Answer

Attachments: Added items

Related Questions:

4wd switch stays on

Turn signals reverse lighs dont work need a wire diagram for this 1997 izuzu rdeo 4x4

Back up lights won't work on 2004 Isuzu Rodeo. Bulbs and fuses are all good.

I own an Isuzu Wizzard (1998, diesel, automatic, fuel injection). One morning I started the car and I heard a slow, heavy stuttering. The gas pedal only reacted after 30 seconds. When driving, the car...

I have a 2003 isuzu rodeo. Sometimes it is hard to put into reverse. I can usually get it to work in 1 or 2 tries. the abs light came on a couple of times. what could make this happen?

2004 isuzu rodeo check engine light stays on and reduced power light goes on and off but when on car looses speed. When reduced power light goes off, vehicle lunges forward and runs fine. My mechanic and...

Check trans light on....no power

1995 Isuzu Rodeo 4X4 3.2 5 speed manual, reverse lights on in 1st

Hi I HAVE A ISUZU WIZZARD 3.0 WITH 4jx1 engine,it hard to started,diesel knock when it idle,engine light stay on with a code p10193 or p1393,already replace fuel filter,engine oil,train and renew a diesel...

My 2000 isuzu trooper reverse lights always stay on no matter what gear I am in. I need to know where to find the reverse light switch.

Not finding what you are looking for?

1998 Trooper

4wd switch stays on

Related Topics

Ask a Question

Popular Questions

Isuzu 320 KB v6 camshaft timing diagram posted to wrong forum.

Isuzu bighorn diesel 4jg2 engine timing diagram

Isuzu Trooper (Bighorn) 4JX1 Engine Common rail

2002 ISUZU TROOPER, TOD CHECK LIGHT IS FLASHING,

My ABS light on my Isuzu trooper remain on how can I reset

Check Out the Latest Top Trucks Report!

Top Isuzu Experts

ZJ Limited

Thomas Perkins

Ronny Bennett Sr.

Are you an Isuzu Expert? Answer questions, earn points and help others

Manuals & User Guides