Battery installation - exactly how do you reach the battery?

There could be several reasons why your Corsa Lite is refusing to start when the weather is hot. Here are some possible causes:

1. Weak battery: High temperatures can cause the battery to lose its charge quickly, and if the battery is already weak, it may not be able to provide enough power to start the engine.
2. Faulty starter motor: If the starter motor is faulty, it may struggle to turn the engine over, especially when the engine is hot.
3. Clogged fuel filter: A clogged fuel filter can prevent fuel from reaching the engine, which can cause starting problems.
4. Vapor lock: In hot weather, the fuel in the fuel lines can vaporize, causing a vapor lock, which can prevent fuel from reaching the engine.
5. Ignition problems: If the ignition system is not functioning properly, the engine may not start, especially in hot weather.

To determine the exact cause of the problem, you may want to take your car to a qualified mechanic who can run a diagnostic test and identify the issue. They can then make the necessary repairs to get your car up and running again.

In newer cars battery is installed in the Trunk/Wheel well/under rear seat/under cover and so not possible to reach it directly to check them. Connection from these batteries is brought to a convenient location/Junction box which is what called Conjunction Box.

I’m happy to assist further over the phone at https://www.6ya.com/expert/uttamjeet_2f3adc18600f8ede

Open the hood of your vehicle and disconnect the battery's negative-terminal cable with a socket wrench.
Remove the cover from the fuse block and locate the high-beam headlamp fuse. Most vehicles have two, one for the right headlamp and one for the left headlamp. For the exact location of the fuse, check through your vehicle's user's guide.
Use a fuse puller tool to remove the high-beam headlamp fuse and install a replacement fuse in its place. Reattach the cover to the fuse block.
Reach behind the high-beam headlamp and disconnect its electrical connector by pulling it straight out. Rotate the old bulb counterclockwise and pull it out to remove it.
Install a replacement bulb and reattach the electrical connector to the headlamp. Consult your vehicle's user's guide for the exact type of bulb to use. Close the hood when done.
V15 GDS VCI Diagnostic Tool for Hyundai and Kia

remove battery cables at exactly noon lol or just use the 2 small button just beside the clock.. hold and they will flash the #s push button for hour & then minute until reach proper time

sounds like your going to need new positive and negative cables also if they are too short to reach battery, If they can reach battery posts you need new battery cable ends installed.need more help email me

What size of motor, do you have a/c and which belt are you replacing? Not sure about your engine size since you did not list it so please pick the applicable motor:

Sebring Coupe And Avenger (2.5L VIN N Engine)

1. Disconnect the negative battery cable.
   
2. Loosen the tension pulley locknut.
   
3. Rotate the adjusting bolt to decrease the belt tension.
   
4. Remove the drive belt from the engine.
   

To install:

1. Position the replacement belt around the pulleys, making sure the belt routing is correct.
   
2. Adjust the belt by rotating the adjusting bolt until the correct tension is reached. Refer to the procedure earlier in this section for belt adjustment.
   
3. Once the desired tension is reached, secure the locknut. Recheck the belt tension.
   
4. After the belt is installed and adjusted properly, tighten the locknut to 17 ft. lbs. (23 Nm).
   
5. Connect the negative battery cable.
   

2.0 DOHC

Power Steering Pump And A/C Belt

1. Disconnect the negative battery cable.
   
2. Loosen the tension pulley locknut.
   
3. Rotate the adjusting bolt to decrease the belt tension.
   
4. Remove the drive belt from the engine.
   

To install:

1. Position the replacement belt around the pulleys, making sure the belt routing is correct.
   
2. Adjust the belt by rotating the adjusting bolt until the correct tension is reached. Refer to the procedure earlier in this section for belt adjustment.
   
3. Once the desired tension is reached, secure the locknut. Recheck the belt tension.
   
4. After the belt is installed and adjusted properly, tighten the locknut.
   
5. Connect the negative battery cable.
   

If you cannot reach the actual terminals on the battery, there usually is an alternate way of accessing its power. Being that I don't exactly know this specific car, bring it to a mechanic and ask them to take a look for you. They won't charge you anything. Ask him the same thing you're asking us.

http://www.autozone.com/shopping/repairGuide.htm

new battery should be fairly close physically to the original. Terminals must match, especially if cables don't reach!!! Bring it back and get the right one. If you cannot for some reason, you can get longer cables and remove the lip on the battery tray in most cases to make it fit. But, do you really want to do that???

Was this starter from a discound retail parts store? well most times those cheap starters are no rebuilt very well you get what you pay for, Try this when it won't start reach and hit the starter with whatever you can a good sharp hit not too hard if it starts after you tap on it I have always had it be the starter the small wire goes on the "S" terminal and the big battery wire goes on the stud on the solonoid any other fuse link wires with the same size eyelet should also go on the same stud.