Doors were shut last fall and we cant open them - how do we get the key lock to relase and open? the Key turns but no clicking etc.. have to get door open to work on it so whats the best way

I've had a strange issue with my drivers door the last week. I go out and unlock my door with wireless clicker. Then I reach in put the key in the ignition start the truck, make sure the defrost is on. Then I step away and slam the door, 'bump',,, I look back, the door did not click shut, again I slam the door 'bump'..it does not click shut. Bump Bump Bump...I try to shut it...then I reach in and push the lock/unlock button , lock/unlock...lock/unlock...on the door..click..click...it does beep or the horn toots..remember trucks key is in ignition , truck running, and I'm clicking the button on the inside of the door. Finally the door will shut and hold closed , once it was not locked,,,once it was shut and locked. I had to get my other set of keys to unlock the door.

The actuator/latch is bad. Basically a spring in it is not tight enough to close it.

Locking/Unlocking the doors from the outside
This is done using the RENAULT Card; see the "RENAULT Card" information in Section 1.
In certain cases, the RENAULT card may not work:
- if the RENAULT card battery is weak, flat, etc.
- if equipment operating on the same frequency as the card (mobile phones, etc.) is used;
- vehicle located in a high electromagnetic radiation zone.
It is then possible:
- to use the key integrated into the card to unlock the front left-hand door;
- to lock each of the doors manually;
- to use the interior door locking/unlocking control (refer to the following pages).
Using the key integrated in the RENAULT card
Insert key 1 into the lock in the driver's door and lock or unlock. Locking the doors manually
Turn screw 2 with the door open (using the end of the key) and close the door.
This means that the doors are then locked from the outside.
The doors may then only be opened from the inside or by using the key in the front left-hand door. Interior locking/unlocking door control
Switch 3 controls the doors, boot and, depending on the vehicle, the fuel filler flap simultaneously.
If a door or the tailgate is open or not closed properly, the doors and tailgate lock/unlock quickly.
If you need to transport objects with the boot open, the other opening elements can still be locked: with the engine stopped, press switch 3 for more than five seconds to lock the other opening elements.
Locking the doors without the RENAULT card
For example, in the event of a discharged battery or the RENAULT card temporarily not working, etc.
With the engine switched off and an opening element (door or boot) open, press and hold switch 3 for more than five seconds.
When the door is closed, all the doors and the tailgate will be locked.
Unlocking the vehicle from the outside is only possible with the RENAULT card in the vehicle's access zone or using the key integrated in the RENAULT card.
Door and tailgate status indicator
With the ignition on, the warning light integrated in switch 3 informs you of the locking status of the opening elements:
- indicator light on, the doors and tailgate are locked,
- indicator light off, the doors and tailgate are unlocked.
When you lock the doors, the indicator light remains lit and then goes out.

The clicking you hear is the vehicle asking for the program sequence to reprogram the locking system. Apparently something threw it out of sequence, ( a battery change , jumpstart, voltage spike , etc). The programming sequence that mazda uses is really kinda crazy. I was able to locate the sequence to try. If it does not work have the dealership flash the pcm, (another word for reprogram the powertrain control module). Here is the sequence:
1) Get in MPV with ignition key, and all fobs for the vehicle.
2) Close all doors and remove ignition key if it is in ignition.
3) Open driver's door
Note: Steps 4 and 5 must be completed in under thirty seconds.
4) Repeat the following three times
a) Insert ignition key
b)Turn ignition switch to on and then to lock
c) Remove ignition key
5) Repeat the following three times
a) Close driver's door
b) Open driver's door
Locks should all lock and then unlock within a couple of seconds--you'll hear the clicking sound
6) Press any button two times within five seconds on fob being programmed.
Locks should again lock and unlock
7) Repeat step 6 for all other fobs being programmed. When done with last fob, wait a few seconds and then you should be done with the reprogramming. Each fob should now work for this vehicle.

hi jerome
I have the procedure for Toyota auto lock, is worth to try it
AUTOMATIC LOCK SETTING
1) Step in the vehicle and make sure that all doors are closed completely
2) Insert the key into the ignition key cylinder.
3) Wait for more than 5 seconds.
4) After turning the key to the ACC position, turn the key from the ACC to the
ON position 5 times within 10 seconds (Last position : ON).
? Status Monitor LED will illuminate for 30 seconds.
Note : In case you implement 6 times or more by mistake,
action steps 6)-8) you made will be canceled.
Please retry from step 2).
5) While the LED is illuminated :
• Open and close the driver's door 2 times.
• Turn the key to the ACC position.
? LED will continue illuminating.
? Indicator lights will flash 2 times.
Ignition controlled door lock ON :
6) While the LED is illuminated:
• Open and close the driver's door 1 time.
• Turn the key ACC-ON-ACC 1 time (Last position : ACC).
? Indicator lights will flash 1 time.
? LED will extinguish.
Ignition controlled door lock OFF :
6) While the LED is illuminated :
• Open and close the driver's door 2 times.
• Turn the key ACC-ON-ACC 1 time (Last position : ACC).
? Indicator lights will flash 2 times.
? LED will extinguish.

put key in ignition turn key to number 2 lights on dash battery etc. then press the fob. till the doors lock then it is rest.

ummm use a key...if that doesn't work call AAA

1. sitting in driver seat, with driver's door OPEN, press lock/unlock button ON THE DRIVERS DOOR to lock all doors, then manually unlock driver door only.
2. Insert YOUR key in ignition, DO NOT TURN, then remove key.
3. Using the same lock/unlock button ON THE DRIVERS DOOR, slowly press lock-unlock in 5 cycles
4. Shut door.
5. Open door.
6. Using the same lock/unlock button ON THE DRIVERS DOOR, again slowly press lock-unlock in 5 cycles
7. With the door open insert your key into the ignition, turn to 'on' position (DON'T START), wait 5 seconds. Turn off and remove key.
8. Locks should cycle once (Car will lock and then unlock once by herself). If they don't cycle or they cycle more than once, do steps 1-7 over.
9. Now using the remote, push lock button, hold for one second, then release the button. The locks should cycle once. If not, start over and go slower.
10. Close the door.
11. Open the door.
12. Press the lock button on the remote. The locks should do a lock-unlock cycle.
13. Close the door
14. Press the lock button on the remote, the doors should lock.
15. Press unlock button and the doors should unlock.

Long beep to follow if successful.

Program your factory keyless entry functions
For 2001+ Tacomas equipped with a factory alarm or keyless entry, here are some programming options that allow you to adjust the way your locks work.
The first programming option allows you to set the entry unlock to: (A) unlock the driver door with one push, and the remaining doors with a second push OR (B) unlock all of the doors with a single push.

• Open the driver's door. Remove the key from the ignition switch.
  
• (Complete these steps within 40 seconds)
  
  1. Insert the key into and remove it from the ignition switch 2 times.
     (IN - OUT - IN - OUT)
     
  2. Close, then open the driver's door 2 times.
     (SHUT - OPEN - SHUT - OPEN)
     
  3. Insert the key into and remove it from the ignition switch 1 time.
     (IN - OUT)
     
  4. Close, then open the driver's door 2 times.
     (SHUT - OPEN - SHUT - OPEN)
     
  5. Insert the key into the ignition switch and leave it in.
     
  6. Close the driver's door.
     
  7. Turn the key from LOCK to ON 4 times, ending at LOCK
     (LOCK - ON - LOCK - ON - LOCK - ON - LOCK - ON - LOCK)
     
  8. Wait for the locks to stop, then remove the key from the ignition switch.
     
• On the key fob, press and release both LOCK and UNLOCK buttons at the same time.
  
  1. [For all doors unlock] press and release the UNLOCK button.
     
  2. [For driver door unlock] press and release the LOCK button.
     
• Open the driver's door. The programming is complete. If programming did not occur, start over.