What is the oil pan bolts torque spec for a 2002 jaguar X-type V-6

12-13 foot pounds

Pontiac Engine Torque Specs

Butler Performance https://butlerperformance.com > p-34888-pontiac-engi...
Pontiac Engine Torque Specs ; Oil Pump Cover Bolts, Engine Oil, 15 ft-lbs. ; Windage Tray, Engine Oil, 15 ft-lbs. ; Oil Pan, Engine Oil, 12 ft-lbs. ; Camshaft ...

Oil and Transmission Pan Bolts. How much torque?

GMForum.com https://www.gmforum.com > ... > 1992-1999
Jun 12, 2003 - the Torque Specifications for the Xmission Oil Pan Bolts are 12-13 Ft. Lbs. Works for me.

Transmission pan Torque spec
Apr 28, 2017
4T65E-HD transmission pan bolt torque values
Feb 8, 2008
More results from www.gmforum.com

2004 Pontiac Sunfire 2-dr Transmission Pan Gasket ...

MyCarSpecs https://www.mycarspecs.com > pontiac > sunfire > 2004
The transmission pan gasket helps to seal in transmission fluid and keep it from leaking everywhere. This will degrade over time and need replacement, ...

..

Bobby, oil pan bolt torques for 4.0 Wrangler. Oil Pan Bolts 1/4 84 in-lbs Oil Pan Bolts 5/16 132 in-lbs As far as sequence, see last link, start in center, criss cross pattern tighten snug all, then repeat to torque spec.
Check the attached links,instruction and guides, Good luck
"I hope this helped you out, if so let me know by pressing the helpful button. Check out some of my other posts if you need more tips and info."
Oil Pan Gasket leaking
http://jeephorizons.com/tech/99_40l_torque_specs.html
98 jeep 4 0 oil pan bolt torque sequence specs Google Search

SOHC V6 Torque Specifications - Ford Explorer and Ranger Forums ...

https://www.explorerforum.com/forums/showthread.php?t=406687

Apr 25, 2014 - SOHC V6 Torque Specifications Under the Hood. ... related to the Ford SOHC V6 4.0L engine used in Explorers, Mountaineers, Mustangs and Rangers. .... Oilpan (sheet metal) to crankcase reinforcement section bolts: 80 lb-in (E/MWM) ....Ranger Mountaineer - Sport thru '03 - 2nd Generation, 2002 - 2005 ... Transmission pan drop
5 posts
May 7, 2012
SOHC V6 Timing Chain Inspection & Repair
19 posts
Aug 10, 2010
Another transmission won't go after fluid change
19 posts
Mar 14, 2009
Help with 4.0 SOHC timing
15 posts
Mar 12, 2006
More results from www.explorerforum.com

[PDF]SPECIFICATIONS > TORQUE SPECIFICATIONS

www.askatech.com/askatechlive/forums/resourcehandler.ashx?a=5581

Jan 6, 2014 - TORQUE SPECIFICATIONS ... ENGINE - 4.0L SOHC. 2002 FordExplorer Sport Trac 4.0L Eng. (1). (2) ... Oil Pan Ladder Frame Bolts (Inside).

Torque Specifications - AutoZone

To install: Place a 3mm bead of RTV sealant on the oil pan sealing flange.
Install the oil pan and torque the 1 inch bolts to 6-9 ft. lbs. (8-12 Nm) and the 1.5 inch bolts to 14-22 ft. lbs. (19-29 Nm).
Install the starter assembly.
Install the flywheel and clutch housing cover.
Lower the vehicle and refill the crankcase with the specified engine oil.
Start the engine and check for oil leaks.

Here's a link to the oil pan bolt specs.

Here's a link to the oil pan removal guide with pan bolt torque specs.

It sounds like you have the seal crimped which is a common issue. Pull and clean the old seal off both the pan and the transmission. Apply a thin steady bead of Form-A-Gasket to the pan and the transmission where the seal makes contact and then carefully replace the pan with the seal in place and tighten all the bolts to 20 lbs torque. Then to 30 lbs torque, be careful not to strip any bolts by over tightening. Let this setup for at least 30 minutes. When you put the bolts back in place, start with one in the center of the pan at 12 o'clock, then 6 o'clock, then 3 then 9 then replace the corners and fill in the rest working from side to side until they are all in place.

OIL PAN OR TRANSMISSION PAN BOLTS TORQUE ABOUT 7 FT LBS. CAN GET SPECS ON BOLTS SIZES. IF BOLTS SIZES IS 13M I4M 15 M TORQUE BOLTS ABOUT 55 TO 80 FT LBS

OIL PAN BOLTS TORQUE IS 96 - 120 INCH POUNDS

torque specs for these bolts can be found in a Haynes or Chilton manual availiable from your local parts store, or maybe at your local library, however these bolts are usually no more than 14 ft pounds, unlike cylinder head bolts, the bolts do not need to have any stretch factor to hold the oil pan gasket in place or sealed.