SOURCE: p0051 code, where is the sensor located, where is
Bank 2 is passenger side, sensor 1 is the one up closest to the exhaust manifold. Plug in type (just remove old and plug back into the wiring harness connector) is about $90 at Autozone. You can get a cheaper one that you splice but it's confusing to understand which wires to splice together. Don't forget to buy the special socket, $10, to remove and install the sensor. It's split up the side for the wires. Forget trying to use an open end wrench, socket is best.
SOURCE: Replacing bank 1 sensor 2 and bank 2 sensor 1 oxygen sensors
BANK ONE IS THE REAR BANK OF CYLINDERS AND TWO THE FRONT BANK
SOURCE: location of a o2 sensor 2001 nissan maxima
bank 1 refers to the side of the engine that #1 cylinder is on , and sensor 2 refers to downstream , after the catalytic converter. , this link shows bank 1 on a 2001 nissan maxima V6 being on the firewall side . if you had a 4 cylinder it would be downstream after the catalytic converter .
http://www.autozone.com/N,26200242/shopping/specsSelect.htm
SOURCE: where is the bank 2 sensor 1 located.
Oxygen sensors are always numbered like this:
Bank 1 sensor 1
Bank 2 sensor 1
Bank 1 sensor 2
Bank 2 sensor 2
some manufacturers use a kind of shorthand that reads different, but means the same thing:
Sensor 1/1 or O2s 1/1
Sensor 2/1 or O2s 2/1
Sensor 1/2 or O2s 1/2
Sensor 2/2 or O2s 2/2
Bank 1 is always the side of the engine where cylinder number 1 is located and, of coarse, Bank 2 is the opposite side.
On a 4 cylinder engine, there is only 1 bank and it is always referred to as Bank 1.
Sensor 1 is always the upstream sensor (The one located BEFORE the catalytic converter)
Sensor 2 is always the downstream sensor (the one that is located AFTER the catalytic converter.
Most GM engines have #1 cylinder located on the left bank, (or Driver's Side) of the engine,
So, the answer to your question would be that you are looking for the sensor located before the catalytic converter on the right (or Passenger Side) of the truck.
SOURCE: location of the bank 1 sensor 2 O2 sensor on a 2001 ford escape
B1 means the sensor is located on the same bank of the engine that has the #1 cylinder. B2 is located on the opposite bank.
S1 means the sensor is located BEFORE the catalytic converter
S2 means the sensor is located AFTER the catalytic converter
You didn't say which engine you have, so I've included the diagrams of both 4 cyl and 6 cyl so you can see the banks
Fig. Fig. 3: Oxygen sensor-4.3L engines
Fig. Fig. 4: Oxygen sensor-5.0L and 5.7L engines
Fig. Fig. 5: Oxygen sensor-7.4L engines
Oxygen sensors are always numbered like this:
Bank 1 sensor 1
Bank 2 sensor 1
Bank 1 sensor 2
Bank 2 sensor 2
Some manufacturers use a kind of shorthand that reads different, but means the same thing:
Sensor 1/1 or O2s 1/1
Sensor 2/1 or O2s 2/1
Sensor 1/2 or O2s 1/2
Sensor 2/2 or O2s 2/2
Bank 1 is always the side of the engine where cylinder number 1 is located and, of coarse, Bank 2 is the opposite side.
On a 4 cylinder engine, there is only 1 bank and it is always referred to as Bank 1.
Sensor 1 is always the upstream sensor (the one located BEFORE the catalytic converter)
Sensor 2 is always the downstream sensor (the one that is located AFTER the catalytic converter.
Hope helps (remember to rate this).
3,966 views
Usually answered in minutes!
What side ? Driver side or passenger side
×