Question about 2000 Chevrolet Venture

1 Answer

I want to un program my keyless entry remote on my 2000 chevy so that i can program it to my 2004 chevy truck how do i do that

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    New Friend:

    An expert that has 1 follower.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Contributor
  • 13 Answers

Do you still have both cars? If not, you don't have to un-program the remote to use it on another car.

If so, then simply reprogram the remotes you want to use on the 2000 chevy and then when you are done only the ones u just programmed will work on it, then simply repeat the process on the 2004 chevy truck.

Posted on May 03, 2010

Ad

1 Suggested Answer

Anonymous

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I went through programing as far as lock recycling but wont go any further


Remote Transmitter Programming NOTE: All keyless entry remote transmitters must be programmed at the same time.
NOTE: Programming (or reprogramming) the keyless entry remote transmitters into the central security module can be accomplished using a diagnostic tool or by carrying out the following steps.
  1. Turn the ignition switch from OFF to RUN eight times within 10 seconds, ending in RUN. If the module has successfully entered program mode, it will lock and then unlock all doors.
  1. Within 20 seconds, press any button on a keyless entry remote transmitter, and the doors will lock and then unlock to confirm that each keyless entry remote transmitter has been programmed. Repeat this step for each transmitter.
  1. If the door locks do not respond for any keyless entry remote transmitter, wait several seconds and press the button again. If the door locks still fail to respond, refer to Inspection and Verification.
  1. Turn the ignition switch to the OFF position, or wait up to 20 seconds after Step 2, to exit program mode. If a keyless entry remote transmitter has been programmed (or reprogrammed), the doors will lock and unlock one last time to confirm.

Mar 18, 2016 | 2004 Ford F150

1 Answer

Is there a way to reset keyless entry for 04 endeavor?


Search Results

    2004 Mitsubishi Endeavor Key Fob Remote Programming ...

    blog.keylessentryremotefob.com/.../04/2004-mitsubishi-endeavor-key-fo...
    Apr 25, 2013 - 2004 Mitsubishi Endeavor Key Fob Remote Programming Instructions ... you might have visit us at Keylessentryremotefob.com You can also ...

    Mitsubishi - Free Keyless Remote Fob Entry programming .

    How To Replace Mitsubishi Endeavor Key Fob Battery 2004 ...

    ? 2:04
    www.youtube.com/watch?v=yeQRdre7O0Q
    Oct 31, 2014 - Uploaded by Keyless Entry Remote Inc
    ... will show you How To Replace Mitsubishi Endeavor Key Fob Battery 2004 2005 To Order This Remote ...

Nov 01, 2015 | Cars & Trucks

1 Answer

Programming keyless entry key fob for 2000 chevy


you need to call the nearest chevy dealer with you vin, and get the part number from them, there are 2 numbers on the back of the remote, see if they match what the dealer tells you. Have an automotive locksmith program, should cost about 75.00 to do.

Jan 27, 2010 | 2000 Chevrolet Malibu

1 Answer

How to program a keyless entry for land rover


MOST OF THE TIME WHEN YOU HAVE PROBLEMS IN THE REMOTE AND KEYLESS ENTRY.THE DEALERSHIP HAS TO REPROGRAM IT.BUT FIRST CHECK ALL THE FUSES AND RELAYS.IF THEY ARE OKAY.THEN DEALERSHIP HAS TO FIX.

Sep 16, 2009 | 2004 Land Rover Discovery

1 Answer

How do i reset the the keypad for the keyless entry on the door


how to program keyless remote on chevy malibu 2004

Jun 18, 2009 | 2002 Ford Explorer

2 Answers

Program fob


Instructions to program a keyless entry remote for a Chevy Silverado. They also work on 2003, 2004 and 2006 Suburbans.
  1. Close all the vehicle doors.
  2. Insert the ignition key into the ignition lock cylinder.
  3. Press and hold the DOOR unlock switch.
  4. While holding the DOOR lock switch in the unlock position, cycle the ignition ON, OFF, ON, OFF.
  5. Release the DOOR unlock switch. The doors will lock and unlock to confirm the program mode.
  6. Press and hold the LOCK button and the UNLOCK button simultaneously on one keyless remote. After a delay of approximately 15 seconds, the doors will lock and unlock to confirm the programming of that transmitter.
  7. Repeat the previous step to program up to four transmitters.
  8. Turn the ignition switch to the RUN (one more click forward) position in order to exit the keyless entry transmitter mode.
  9. Operate the transmitter functions in order to verify correct system operation

Apr 19, 2009 | 1999 Chevrolet Silverado 1500

2 Answers

My remote for the keyless entry does not work.


does trunk button work? panic button?
here's 2003 info:


  • The doors do not lock/unlock using the remote transmitter
  • Remote transmitter.
  • Driver door module (DDM).
  • Go To Pinpoint Test G .

SECTION 501-14: Handles, Locks, Latches and Entry Systems 2003 Town Car Workshop Manual
GENERAL PROCEDURES Remote Transmitter Programming
  1. Cycle the ignition from OFF to RUN four times within three seconds. The locks will then lock and unlock, confirming that the program mode has been entered.
  1. NOTE: When the first keyless entry remote transmitter is programmed, all other keyless entry remote transmitters are erased.
    Press any button on the transmitter to be programmed.
  1. If additional keyless entry remote transmitters are to be programmed, repeat Step 2 within 7.5 seconds.
  1. To exit program mode, turn the ignition to START or wait 7.5 seconds.
--------------------------------------------------------------
report back

Mar 22, 2009 | 2004 Lincoln LS

1 Answer

How can I program my replacement remote


Check your owners manual. You might be able to do it through the controls on the radio.

Dec 04, 2008 | 2000 Chevrolet Impala

1 Answer

2000 dodge neon alarm


This is what i found but you need one fob.

here is another way if you can get it done( i bevlieve) There is a box under the dash of your can it says keyless entry if you have the right box and the fab just plug and play.

Make sure you get the screws in the defrost vent there is some screws and then it there is snaps


http://shopping.msn.com/specs/keyless-entry-remote-fob-clicker-for-2004-dodge-neon-with-do-it-yourself-programming-requires-1-wor/itemid1124228415/?itemtext=itemname:keyless-entry-remote-fob-clicker-for-2004-dodge-neon-with-do-it-yourself-programming-requires-1-wor

Nov 15, 2008 | 2002 Dodge Neon

2 Answers

How do you program a new keyless enrty remote for a 2004 chevy cavalier ls sport


How can I Program my Keyless remote for my 2004 Chevrolet Cavalier?My E-Mail address is Johnhegedus@ptd.net

Oct 16, 2008 | 2004 Chevrolet Cavalier

Not finding what you are looking for?
2000 Chevrolet Venture Logo

235 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

Marvin
Marvin

Level 3 Expert

85223 Answers

Jonah Oneal

Level 3 Expert

14092 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22485 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...