Wondering where the windshield washer fluid pump is its not pushing fluid out

There is a electric motor that pumps washer fluid . Located in the bottom of the washer fluid tank .
Wash Operation (Front and Rear Wipers)
The front and rear washer systems use the same windshield washer fluid pump. When either the front or rear wiper is in the washer position voltage will be supplied to one side of the windshield washer fluid pump (depending on whether it is front or rear), while the other side of the pump is grounded.
At this point, the windshield washer fluid pump sprays solvent onto the windshield. When the front or rear washer is activated, the BCM receives an input from the switch that is activated. The BCM will control the wipers while in the WASH mode. The BCM will control either the front wiper relay or the rear wiper relay to turn on the wipers. The windshield wipers operate at low speed for 3 swipes and returns to the park position.

When turning on the washers do you hear the motor run ? Have some one try it while you listen at the washer fluid tank ! These pump motors do go bad .
turn OFF the ignition.
Disconnect the harness electrical connector of the windshield washer fluid pump.
Connect a test lamp from the windshield washer pump control circuit to a good ground .
Turn ON the ignition, with the engine OFF.
Press the front washer switch.
Does the test lamp illuminate?
YES or NO !

A washer pump in a car's windshield wiping system moves washer fluid from a reservoir through hoses. The motorized pump pressurizes the fluid to allow it to be squirted from the hoses through nozzles onto the front and/or rear windshield of a car. The washer fluid helps windshield wipers get rid of rain, dirt, or other objects that can interfere with a driver's visibility. If your washer fluid is not being sent out when activated, the solution could simply be filling the washer system's reservoir with more fluid or cleaning the nozzles and hoses. In more severe cases, the washer pump may need to be replaced. Here are steps to troubleshoot a windshield-washer pump.

Try this link in case you are stuck:

How to Troubleshoot Windshield Washer Pump

Here is another YT video for a similar purpose:

Windshield Washer Pump and System Diagnosis

Did they connect the power to the pump?
yes it could be a fuse.

Is your wiper fluid level good?Look for leaks at pump,it's connected to container,also check your hoses leaving pump to windshield,could be loose or binding.

you say the pump is good,. so its pumping? if so the washer hose may be broken? nozzles clogged?

dirt could have gotten in the lines. take a needle and poke in the holes the washer fluid comes out . to be sure, take the line off the pump and try it. if the pump shoots washer fluid- the line is clogged. if not, the pump could be clogged

Are you getting power to the pump if not check your fuse if you are check the hose to the windsheild if cut or clogged

Probably need to replace the pump. Separate pumps for front and rear. Check with a test light to see if there is power to the pump. If it has power but won't work, replace the pump. If no power, you have a wiring issue. Be sure to turn the switch on and have someone push the washer button when you are checking for power. There won't be any until you push it to "wash".

the pump motor likely is bad. get a used washer fluid reservoir at a pick n pull yourself or at car-part.com. page with * is lowest cost.

Pump and Reservoir, Windshield Washer Removal

1. Disconnect the battery ground cable (14301).
   
2. Raise and support the vehicle.
   
3. Remove the RH wheel (1007).
   
4. Remove the RH front fender splash shield (16103). Refer to Section 01-02 for the removal procedure.
   
5. Remove the windshield washer reservoir top bolt.
   
   
6. Disconnect the windshield washer reservoir fluid level sensor electrical connector.
   
7. Disconnect the rear window washer pump electrical connector from the rear window washer pump.
   
8. Disconnect the windshield washer pump electrical connector from the windshield washer pump (17664).
   
9. Place a suitable drain pan under the windshield washer reservoir (17618) and drain the washer fluid.
   
10. NOTE: The rear window washer hose end is color-coded, matching the connector on the rear window washer pump. Match the colors to ensure proper installation.
    
    Disconnect the washer hoses from the windshield washer pump and the rear window washer pump on the windshield washer reservoir.
    
    
11. Loosen the two windshield washer reservoir side bolts.
    
12. Remove the windshield washer reservoir by sliding it out of the side slots.
    
13. Remove the windshield washer pump.
    
    Installation

To install, reverse the removal procedure. Tighten the lug nuts (1012) to 98-118 Nm (72-87 lb-ft).

not likely that fuse blew but check fuse box for wiper fuse and see if blown, when u fill fluid, turn ignition on but not running hit squirter and listen for pump noise if noise is present then hit repeatedly and look if there is any leakage dripping and trace leak, if no noise check resivor for debrie floating (posisible blockage) last thing is check for power at pump with wire probs