What would the torque setting for a 86 corolla head bolts and cam bolts thank you Jason

The torque specification for the head bolts on a 1997 Toyota Corolla is usually between 26 and 30 foot-pounds. It's important to note that the torque specification can vary depending on the specific engine and head bolt type, so it's always best to consult a service manual or other reliable source for the most accurate and up-to-date information.

It's also important to follow the proper tightening sequence when installing the head gasket. The tightening sequence is usually specified in the service manual and is designed to ensure that the head bolts are tightened evenly and to the proper torque specification.

I recommend using a torque wrench to ensure that the bolts are tightened to the proper torque specification. It's also important to use a torque angle gauge to ensure that the bolts are tightened to the proper angle.

I hope this helps! Let me know if you have any other questions.

This manual has everything but cam torque

http://www.championbrands.com/aera-torquespecs.pdf

(1) Apply a light coat of engine oil to the threads and under the heads of the cylinder head set bolts.
(2) Using several steps, uniformly install and tighten the 10 cylinder head set bolts and plate washers with a 10 mm bi-hexagon wrench in the order shown in the illustration. Torque:
70 N·m {714 kgf·cm, 52ft·lbf} (c) Mark the front of the cylinder head bolts with paint.

(d) Further tighten the cylinder head bolts 90° as shown in the illustration.
(e) Check that the paint mark is now at a 90° angle to the front. cam bearing caps; Using several steps, uniformly tighten the 10 bearing cap bolts in the sequence shown in the illustration.

Torque:
No. 2 Bearing cap -
30 N·m {301 kgf·cm, 22ft·lbf}
No. 3 Bearing cap -
9.0 N·m {92 kgf·cm, 80in·lbf}

Torque setting Toyota Land-cruiser 80 Series 4.5 1995-98
Engine code: 1FZ-FE, 1HD.
Stage 1: 20 Nm (Start tightening bolts from center to outwards)
Stage 2: 39 Nm
Stage 3: Rotate each bolt by 90 Degrees.
Stage 4: Further rotate each bolt by 90 Degrees

A Chiltons/Haynes repair manual from your local auto parts store that covers your year/make/model has all of your answers under the "engine rebuild" heading.

Commonly Asked Torque Specs in foot pounds
The main bolts have a torque of 76 lb.-feet and the cylinder head bolts have 62 lb.-feet of torque. The cylinder head studs have 70 foot-lbs of torque, the cam timing gear have lb.-feet of torque, and the cam bearing bolt has 14 lb.-feet of torque.

Crankshaft Torque Specs

• The stock rod bolts have 46 lb.-feet of torque and the ARP rod bolts have 50 lb.-feet of torque. The crankshaft pulley has 116 lb.-feet of torque, while the flywheel has 80 lb.-feet of torque.
  

Other Torque Specs

• The intake manifold and exhaust manifold have 33 lb.-feet of torque each and the oil pan bolts have 9 lb.-feet of torque. The cam timing gear has 58 lb.-feet of torque and the cam bearing bolt has 14 lb.-feet of torque. One set of timing cover bolts have 9 lb.-feet of torque and another set has 29 lb.-feet of torque
  

1. Tighten head bolts using the following procedure:
2. Tighten all bolts to 22 ftlbs.
3. Tighten all bolts 59 ftlbs .
4. Loosen all the bolts completely.
5. Tighten all bolts 18 to 25 ftlbs .
6. Turn all bolts 86 to 91 degrees.If an angle wrench is not available, mark all cylinder head bolts on the side facing the engine front. Then, turn each cylinder head bolt 86 to 91 degrees.

There you are as asked for.
Thank you for using FixYA
KL

cam caps 8nm ,cam gear bolt --use a locktite product and tighten tight

The head bolt torque is 48ft. pounds and the camshaft bolts are 16ft. pounds thats for a 1.5L S.O.H.C motor.

The 98 Corolla has a "torque-to-distance" spec.

First, torque all 10 bolts to 36 ft lbs (49 NM or 500kgf-cm), in a clockwise fashion, starting with the 2 center bolts.

Second, mark the bolts with a paint mark, and then torque each of the 10 bolts an additional 90 degrees.

Hope this helps, and thanks for choosing FixYa.