Ignition switch will not turn off aux position, key turns to on position but will not turn on or anything off, had to disconnect the battery, please help?

Check the kick starter!!!!

Disconnect the negative battery cable from the terminal on the battery. Remove the upper and lower steering column covers by unscrewing or unclipping them.

2 Remove the steering wheel by lifting off the center cover, disconnecting the horn wire and removing the retaining nut and washer. Make a mark on the steering wheel spline and the wheel itself so you can line it back up precisely. Pull the steering wheel straight back to remove from the shaft.

3 Take off windshield wiper and turn signal switches by pulling them off as you did the steering wheel and disconnect the wiring. Slide the spacer sleeve off of the steering column.

4 Unscrew the ignition switch mounting screws. Pull out the ignition switch. Disconnect the wiring connector from back of the ignition switch. Simply loosen the tabs and pull it out.

5 Insert your key into the ignition. Turn the ignition switch to the locked position. Depress the retaining pin with a small screwdriver and turn the key to the Off position to free the cylinder. Once it is free, turn the key to lock position and remove the key and key cylinder.

6 Install your old key cylinder into the new ignition switch assembly. Make sure the contacts in the cylinder and assembly line up. Reattach wiring to ignition switch, slide it into place, screw in mounting screws and reassemble steering wheel and switches.

the actuator inside the sterring column that the lock cylinder turns is boken, this is a very complex job and is not for the home tech without a factory service manual.

disconnect negative battery cable.place the ignition lock in the off lock position. remove the 2 switch mounting screws.disconnect the switch from the rod.disconnect the wiring and remove the switch.TO INSTALL.ignition switch installation for non tilt columns.move the the ignition switch slider to the off unlocked position move the slider all the way down.then back 2 clicks.the remote rod hole in the ignition switch slider should now be centered.insert the remote rod in the ignition switch slider hole and install the ignition switch on the steering column.tighten the attaching screws to 35 inch lbs.ignition switch installation for tilt columns.insert the ignition key in the lock cylinder and turn the cylinder to the off unlock position.move the ignition switch downward to eliminate any slack and tighten the attaching screws to 35 inch lbs.

TWO THINGS TO TRY... FIRST DISCONNECT BATTERY. LEAVE DISCONNECTED FOR TWENTY MINUTES, WHILE DISCONNECTED TURN THE IGNITION KEY TO THE RUN POSITION AND LET SIT...AFTER 20 MINUTES TURN KEY OFF RECONNECT BATTERY.. THEN TRY IF STILL NOTHING, THEN TRY TURNING KEY TO THE RUN POSITION AND LEAVE FOR 10 MINUTES.. THEN TRY IF STILL NO THEN GET BACK WITH ME FOR FURTHER INFO

Try these steps...

Step 1 Disconnect the negative battery cable from the terminal on the battery. Remove the upper and lower steering column covers by unscrewing or unclipping them.
Step 2 Remove the steering wheel by lifting off the center cover, disconnecting the horn wire and removing the retaining nut and washer. Make a mark on the steering wheel spline and the wheel itself so you can line it back up precisely. Pull the steering wheel straight back to remove from the shaft.
Step3 Take off windshield wiper and turn signal switches by pulling them off as you did the steering wheel and disconnect the wiring. Slide the spacer sleeve off of the steering column.
Step4 Unscrew the ignition switch mounting screws. Pull out the ignition switch. Disconnect the wiring connector from back of the ignition switch. Simply loosen the tabs and pull it out.
Step5 Insert your key into the ignition. Turn the ignition switch to the locked position. Depress the retaining pin with a small screwdriver and turn the key to the Off position to free the cylinder. Once it is free, turn the key to lock position and remove the key and key cylinder.
Step 6 Install your old key cylinder into the new ignition switch assembly. Make sure the contacts in the cylinder and assembly line up. Reattach wiring to ignition switch, slide it into place, screw in mounting screws and reassemble steering wheel and switches.

Thanks
Smith

Hi. I've put together a guide that will help you with the replacement of this ignition switch.


Step1 Disconnect the negative battery cable from the terminal on the battery. Remove the upper and lower steering column covers by unscrewing or unclipping them. Step2 Remove the steering wheel by lifting off the center cover, disconnecting the horn wire and removing the retaining nut and washer. Make a mark on the steering wheel spline and the wheel itself so you can line it back up precisely. Pull the steering wheel straight back to remove from the shaft. Step3 Take off windshield wiper and turn signal switches by pulling them off as you did the steering wheel and disconnect the wiring. Slide the spacer sleeve off of the steering column. Step4 Unscrew the ignition switch mounting screws. Pull out the ignition switch. Disconnect the wiring connector from back of the ignition switch. Simply loosen the tabs and pull it out. Step5 Insert your key into the ignition. Turn the ignition switch to the locked position. Depress the retaining pin with a small screwdriver and turn the key to the Off position to free the cylinder. Once it is free, turn the key to lock position and remove the key and key cylinder. Step6 Install your old key cylinder into the new ignition switch assembly. Make sure the contacts in the cylinder and assembly line up. Reattach wiring to ignition switch, slide it into place, screw in mounting screws and reassemble steering wheel and switches.You have just completed the task.Good job:)


Please rate and god bless.

Step1 Disconnect the negative battery cable from the terminal on the battery. Remove the upper and lower steering column covers by unscrewing or unclipping them. Step2 Remove the steering wheel by lifting off the center cover, disconnecting the horn wire and removing the retaining nut and washer. Make a mark on the steering wheel spline and the wheel itself so you can line it back up precisely. Pull the steering wheel straight back to remove from the shaft. Step3 Take off windshield wiper and turn signal switches by pulling them off as you did the steering wheel and disconnect the wiring. Slide the spacer sleeve off of the steering column. Step4 Unscrew the ignition switch mounting screws. Pull out the ignition switch. Disconnect the wiring connector from back of the ignition switch. Simply loosen the tabs and pull it out. Step5 Insert your key into the ignition. Turn the ignition switch to the locked position. Depress the retaining pin with a small screwdriver and turn the key to the Off position to free the cylinder. Once it is free, turn the key to lock position and remove the key and key cylinder. Step6 Install your old key cylinder into the new ignition switch assembly. Make sure the contacts in the cylinder and assembly line up. Reattach wiring to ignition switch, slide it into place, screw in mounting screws and reassemble steering wheel and switches.

You have to use a pin or paper lip to insert in hole in igmition switch to release the lock cylinder. The key has to be in "on" position I think.

Removal

1. Disconnect battery ground cable (14301) .

1. Turn lock cylinder key to RUN position.

1. Place a 3.17mm (1/8-inch) diameter wire pin or small drift punch in hole in upper steering column shroud (3530) under ignition switch . Press retaining pin while pulling out on ignition switch to remove it from lock cylinder housing (22074) .

Installation

1. Install ignition switch by turning it to RUN position and pressing retaining pin. Insert ignition switch into lock cylinder housing . Ensure ignition switch is fully seated and aligned in interlocking washer before turning key to OFF position. This will permit cylinder retaining pin to extend into lock cylinder housing hole.

1. Rotate ignition switch, using lock cylinder key, to ensure correct mechanical operation in all positions.

1. Connect battery ground cable.
   

Neutral safety switch on the tranny?