2003 Acura RSX Logo

Related Topics:

Posted on Mar 18, 2010

I replaced the serpentine belt on my 2002 accura rsx type s it sqeaks and seems loose, is there any way to tighten it....tks

1 Answer

Anonymous

Level 1:

An expert who has achieved level 1.

All-Star:

An expert that got 10 achievements.

MVP:

An expert that got 5 achievements.

Vice President:

An expert whose answer got voted for 100 times.

  • Contributor 431 Answers
  • Posted on Mar 18, 2010
Anonymous
Contributor
Level 1:

An expert who has achieved level 1.

All-Star:

An expert that got 10 achievements.

MVP:

An expert that got 5 achievements.

Vice President:

An expert whose answer got voted for 100 times.

Joined: Mar 09, 2010
Answers
431
Questions
1
Helped
137132
Points
45

I don't Have a manual for this. But in most cases with A serpentine belt the belt trencher is automatic and could be Warren out other then that look see if a pulley bearing could be getting bad .it is also possible you got a defective belt Hope this helps.

  • brtom Jun 11, 2011

    What is a belt trencher?

×

1 Related Answer

Anonymous

  • 5 Answers
  • Posted on Jul 13, 2010

SOURCE: I replaced the serpentine belt on my 2002 accura

The tentioner should keep the belt at the right tention. Are you sure its the belt? I had some squeaking in my 05' RSX and replaced the Tentioner Pulley and the squeaking went away. Maybe this could be the same case. Hope this helps.

Ad

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

0helpful
2answers

Belt slip

Tighten your serpentine belt.
5helpful
1answer

Replace serpentine belet on 2002 santa fa

Below is the diagram you will need to replace the belt. The diagram is for a 6cyl. 2.7 engine (most common for that year). Once the tensioner pulley is loose, route the new belt as diagrammed and while applying pressure, tighten the tensioner pulley.
2002 Hyundai Santa Fe 2.7L with A/C
greg_margo_2.jpg
0helpful
1answer

Replace alternator belt

  • Locate the two belts on the left side (passenger side) of your Mitsubishi Lancer. The outer belt is a serpentine belt, operating four pulleys and the inner belt is your alternator belt.

  • 2

    Follow the serpentine (outer) belt to the three pulleys lined up vertically near the front of the engine compartment. Locate the middle pulley, which is the tension pulley for the belt.

  • 3

    Loosen the bolt on the middle pulley with a socket wrench by turning counter-clockwise. Do not remove the bolt, just turn it a couple of times. Loosen the tensioner bolt on the side of the of the pulley, facing the front of the vehicle.

  • 4

    Remove the serpentine belt and then loosen the bolt on the alternator. With the alternator loose, move it forward so that the alternator belt loosens up and then remove belt from the pulleys.

  • 5

    Install the new alternator belt by placing it over both inside pulleys. Tighten the tension on the alternator belt by moving the alternator back and keeping tension on it by holding it back with a long screwdriver. While the alternator belt is tight, use a socket wrench to tighten up the bolt on the alternator.

  • 6

    Place the serpentine belt back on the pulleys and then use a socket wrench on the bolt on the front of the tension pulley. Once the serpentine belt is tight, tighten up the bolt in the middle of the tension pulley.

  • 7

    Start the Mitsubishi Lancer's engine to test the alternator belt and make sure it is working properly. Once you have verified it is working, turn the engine off.

  • 1helpful
    2answers

    How do you check your timing belt and replace it for 02 acura rsx

    There is no timing belt on the K20. It's a Chain.
    the Belt you see is only the Serpentine Belt. It's attached to a Crank pully so it'll turn the pullies on the AC and Power Stering Pumps, and also the Alternator. This is NOT the "timing belt" as it has nothing to do with the timing or running of the engine.
    visit www.clubrsx.com for more information and forums to solve your problems.
    0helpful
    3answers

    I replaced the serpentine belt on my 2002 accura rsx type s it sqeaks and seems loose is there any way to tighten it....tks

    The tentioner should keep the belt at the right tention. Are you sure its the belt? I had some squeaking in my 05' RSX and replaced the Tentioner Pulley and the squeaking went away. Maybe this could be the same case. Hope this helps.
    2helpful
    1answer

    How do you tighten the serpentine belt?

    if your car has a serpentine belt,which is 1 belt that controls everything,then there is no adjustment.if your belt is loose,then you will need to replace your belt tensioner in order for your belt to tighten.another reason could be that it is time to replace your serpentine belt.hope this info helps.take care and good luck, manny
    2helpful
    1answer

    How to tighten serpentine belt

    if the belt is loose you might have the wrong belt installed on, or the serpentine belt tensioner must to be replaced, they adjust automatic, with spring loaded belt tensioner
    and i will apreciate the ranking to my answer thanx
    Not finding what you are looking for?

    249 views

    Ask a Question

    Usually answered in minutes!

    Top Acura Experts

    ZJ Limited
    ZJ Limited

    Level 3 Expert

    17989 Answers

    Ronny Bennett Sr.
    Ronny Bennett Sr.

    Level 3 Expert

    6988 Answers

    Thomas Perkins
    Thomas Perkins

    Level 3 Expert

    15088 Answers

    Are you an Acura Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides

    Loading...