Need torque for a 2000 Toyota Celicia GT 1.8L

Question edited for a lot more clarity.

Hino J08 engine specs, bolt torques

Barrington Diesel Club
https://barringtondieselclub.co.za > hino > hino-j08
Hino J08E, J08C specs and bolt torques with links to manuals ... Hino J08E Connecting Rod Bolts Step1 = 51 lb.ft ... main bearing cap bolts, connecting rod cap ...

Workshop Manual Hino J08C No.1 ' PDF

Scribd
https://www.scribd.com > document > WORKSHOP-MA...
... SPECIFICATIONS DIESEL ENGINE FOR INDUSTRIAL USE HINO) §=JO8C-T eannzn. ... bearing cap bolt are tightened to the specified torque. ... Connecting rod bearing 16.
"); background-repeat: repeat-x; display: inline-block; overflow: hidden; position: relative; background-size: 14px 11.4px; height: 11.4px; width: 68px;"> "); background-repeat: repeat-x; display: block; background-size: 14px 11.4px; height: 11.4px; width: calc(62px);"> Rating: 4.6 · ‎ 10 votes

Hino J08C Engine Torque Specs

JustAnswer
https://www.justanswer.com > Truck Repair
Sep 29, 2012 - Hi I'm Wayne I will help you with this. Good Morning Rod Bearings 51 FT/LBS + 90° + 45° Main Bearings 196-209 FT/LBS Head Bolts

Missing: connecting ‎' Show results with: connecting

HINO DIESEL ENGINE WORKSHOP MANUAL

jimcontent.com
https://s4b621f162e87bd31.jimcontent.com > name
PDF Cylinder head bolt, crankshaft main bearing cap bolt, connecting rod bearing cap bolt, etc. ! CAUTION. • Measure the overall length of the bolt before.

..

I need all the specs of Isuzu npr 4hg1 engine.Cylinder head bolts torque, crankshaft bolts torque, connecting rod caps bolts torque
.

Main Bearing Torque 67-74 ft lbs
Rod Bearings Torque 28 - 33 ft lbs

Torque settings for V-6 engine.
Main bearing cap bolts torque:
Torque: 27 N·m (275 kgf·cm, 20 ft·lbf)
Mark the front of the main bearing cap bolt with paint.
Re tighten the main bearing cap bolts by 90 degrees.
Check that the crankshaft turns smoothly.

Connecting rod cap bolts torque:
Torque: 24.5 N·m (250 kgf·cm, 18 ft·lbf)
Mark the front of the main bearing cap bolt with paint.
Re tighten the main bearing cap bolts by 90 degrees.
Check that the crankshaft turns smoothly.

Hi I have a Opel Corsa utility 1.7D I am doing the hole engine over but I need the setting for it 2000modle Corsa and the engineers are rebuilding the crank is that okay or risky

TORQUE SPEC FOR ROD BEARING BOLTS 19 - 24 FT LBS TORQUE SPEC FOR MAIN BEARING BOLTS 60 - 70 FT LBS, CRANKSHAFT PULLEY BOLT 85 - 100 FT LBS. MAIN BEARING OIL CLEARANCE .0005 - .0022 CONNECTING ROD OIL CLEARANCE .0008 - .0015 / SHAFT END PLAY .004 - .008 / AND ROD SIDE CLEARANCE IS .004 - .011 HOPE THIS HELP THIS INFORMATION I GAVE YOU IS INLINE 6 -200 AND INLINE 6 - 250 ENGINES

Main bearing caps are 44 Ft/Lbs final torque
Rod bearings are 18 Ft/Lbs and then an additional 1/4 turn.

Head bolts, 105-112 Foot pounds (Final torque)
Final torque must be reached in 3 equal steps. Recheck final torque in sequence.
Main Bearing Caps, Torque in sequence Step 1: torque to 50 Ft/Lbs Step 2: torque to 105 Ft/Lbs
Rod Bearing Caps, 45 Foot pounds (Final torque)

2002 2.0L Duratech.

Don't have 2004 2.3L

• NOTE: Use new connecting rod bearing cap bolts.
  NOTE: Do not fully tighten the connecting rod bearing cap bolts at this stage.
  Install the bearing caps.

• Rotate the crankshaft through 180 degrees and insert pistons 2 and 3.

• Position the corresponding bearing shells, clean and free of oil, into the connecting rod and the connecting rod bearing cap.

• Coat the inner side of the bearing shells with engine oil.

1. NOTE: The crankshaft must rotate freely, if necessary check and adjust the bearing clearances.
   Tighten the main bearing and connecting rod bearing bolts.
   1. Tighten the main bearing bolts in two stages.
      • Stage 1: 25 Nm.
      • Stage 2: 60 degrees.
   1. Tighten the connecting rod bearing bolts in two stages.
      • Stage 1: 35 Nm.
      • Stage 2: 90 degrees.