Torque for 2006 chevy 2500hd cv axle nut - 2006 Chevrolet Silverado 2500HD 2WD

o replace the front passenger CV axle on a 2001 Chevy Venture, you'll need a set of basic tools. Here's a list of tools you might require for this job:

1. Jack and Jack Stands:
   • Used to lift the vehicle safely and provide support during the repair.
2. Wheel Chocks:
   • Ensures that the vehicle stays in place while lifting one end.
3. Lug Wrench:
   • To loosen and remove the lug nuts securing the wheel.
4. Socket Set and Wrenches:
   • Various sizes to remove bolts and nuts securing the CV axle.
5. Pry Bar or Crowbar:
   • Helps in removing components like the wheel hub.
6. Pliers:
   • Used to remove cotter pins and other small components.
7. Hammer:
   • May be needed to tap or gently persuade parts loose.
8. Torque Wrench:
   • Necessary for tightening nuts and bolts to the manufacturer's specifications.
9. Pry Tool or Flathead Screwdriver:
   • Useful for prying apart certain components.
10. Hub Puller (Optional):
    • Sometimes required to remove the wheel hub from the CV axle.
11. CV Joint Clamp Pliers:
    • If your CV axle is secured with clamps, you'll need pliers designed for CV joint clamps.
12. Catch Pan:
    • To catch any transmission fluid that may leak during the process.
13. New CV Axle:
    • Ensure you have the correct replacement part for your specific vehicle.
14. Wheel Bearing Grease:
    • Used to lubricate the CV joint and ensure smooth operation.
15. Service Manual:
    • A repair manual specific to your vehicle can provide step-by-step instructions and torque specifications.

Always follow safety precautions and consult your vehicle's service manual for specific instructions related to your Chevy Venture. If you're not comfortable with the repair process, it's advisable to seek professional assistance.

use the new nut supplied with the CV shaft and torque to new nut Spec.

To change the CV (constant velocity) axles on a 2010 Dodge Avenger with a 4-cylinder engine, you will need to follow these steps:

1. Gather the necessary tools and materials. You will need a jack and jack stands, a lug wrench, a torque wrench, a pry bar, a hammer, and a replacement CV axle.
2. Raise the vehicle and secure it on jack stands. Use the jack to lift the vehicle and place jack stands under the frame for support. Make sure the vehicle is stable and secure before continuing.
3. Remove the wheel. Use the lug wrench to loosen the lug nuts on the wheel and remove it.
4. Remove the CV axle nut. The CV axle nut is located on the inside of the hub. Use a socket wrench or a lug wrench to remove it.
5. Remove the CV axle. Use a pry bar or a hammer to gently pry the CV axle out of the hub. It may be necessary to tap the end of the CV axle with a hammer to loosen it.
6. Install the new CV axle. Slide the new CV axle into the hub and secure it with the CV axle nut. Tighten the nut to the manufacturer's recommended torque specification.
7. Install the wheel. Put the wheel back on the hub and tighten the lug nuts to the manufacturer's recommended torque specification.
8. Lower the vehicle. Use the jack to lower the vehicle off the jack stands and remove them.

Note: If you are not familiar with automotive repair or are not comfortable working on your vehicle, it is recommended to have the CV axles replaced by a professional mechanic.

118 hub nut !!hub bolts are 96 ftlbs.177 and even 144 is to high,you can find them on line to be sure,

Here are the front axle nut torque specs for the 2004 Chevy Silverado 2500HD:
• Axle Shaft nut - 177 ft-lb
• hub and bearing assembly to steering knuckle bolts - 133 ft-lb

80-100 torque and be sure to replace the cotter key/ hammer the crush slot.

Fastener Tightening Specifications 140 foot pounds for the wheels all the way around. Application
Specification
Metric
English
Spare Tire Hoist Retaining Bolt
40 N·m
30 lb ft
Wheel Nuts
190 N·m
140 lb ft

174-231 ft lbs. I would stay closer to 174.

the center bolt for cv axle!103ft-lbs,hub bearing assembly bolts!77ft-lbs

Hi..
On your 05 Chevy 4X4 2500HD.
The Pinion Yoke Nut, 9.75" Axle. the torq spec. is 370 Nm. -- 273 Lb ft.

I hope this help on your question.

Thank you for use fixya...