Question about 1992 Toyota Xtracab

1 Answer

Toyo dyna 92 break lights not working , is there a fuse for this or is it hard wired bulbs ,work fine , ?

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Expert
  • 233 Answers

There is a fuse for the brake lights. Check fuse and replace if blown. If the fuse is not blown, check the bulbs themselves. If the bulbs are good, then the next step is to replace the brake light switch located under steering column attached to brake pedal rod.

Posted on Feb 16, 2010

Ad

1 Suggested Answer

6ya6ya

6ya staff

  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

On my 2004 expedition one of the break lights is not working. the parking light work fine, but when I press the break the passenger side break light does not come on. I changed the bulb and that did not...


check the electrical contacts within the bulb fixture for oxidation or damage. Check also the wires and wire harness for damage or connection problems.

Oct 26, 2010 | 2004 Ford Expedition

1 Answer

Only left tail light does not work. left break light works fine. All other lights work. New bulb, good fuse, and new connector that the bulb plugs into. I can ground the middle wire going into the...


poor ground, check the wire harness, this is the one that comes from front of vehicle to the rear and plugs into the wires that go to the rear lights. trace the wire coming out of the light itself and eventually you will see that it comes to a connector that attaches to the wiring harness.

Sep 03, 2010 | Ford Windstar Cars & Trucks

1 Answer

2001 GMC Jimmy break lights not working but all


Check the brake light switch should be a orange wire with 12v then a white wire with 12v when the pedal is pressed.If htat cks good then ck the hazard switch by moving it up and down and wiggeling the knob with the brake pedal pressed if they start working then your multifunction switch is bad and needs to be replaced.

Feb 20, 2010 | 2001 GMC Jimmy

1 Answer

2006 Chevrolet Silverado 2500HD tail lights stopped working


I am having the same problem on an 04 2500hd there isa 15 amp stop light fuse inside the cab on the side of the instrument panel and a 25 amp stop light fuse under hood. you could also have a break switch issue the switch is located up on the break pedal linkage you should have power on the white wire when you push the pedal in (check with a test light) in my case I have a broken wire along the frame rail in the harness it is a light blue wire,

Mar 08, 2009 | 2006 Chevrolet Silverado 2500HD 2WD

2 Answers

Lower brake lights on 92 camry wont work


YOU MAY NEED A LIGHT FAILURE SENSOR WHICH IS LOCATED IN THE TRUNK ON THE DRIVERS SIDE

Feb 11, 2009 | 1992 Toyota Camry V6

1 Answer

1995 Mercury Tracer Rear lights not working


does the Center brake light work ? I think your looking at replacing the brake light switch !

Dec 19, 2008 | 1995 Mercury Tracer

Not finding what you are looking for?
1992 Toyota Xtracab Logo

170 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

Marvin
Marvin

Level 3 Expert

85216 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22485 Answers

Jonah Oneal

Level 3 Expert

14092 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...