Torque on 3.0 ford taurus head bolts

the torque sequence for head bolts on a 1969 Ford 3000 tractor is as follows: front ' 7 3 1 5 ' ' 8 4 2 6 '. The torque values for the cylinder head bolts are step 1: 55 ft-lb, step 2: 65 ft-lb, step 3: 85 ft-lb

Go to autozones website and make a free account, Log in and put in your make, model and year. Then look for free repair guides

I'm not sure what engine you have in your 95 grand am SO I will give you both the 4cyl and 6cyl Specs. Also you didn't ask for the torque sequence. I will include that as well for both. 2.3 DOHC Quad 4cyl: Torque sequence---> front ' 7 3 1 5 9 ' of engine ' 8 6 2 4 10 ' Step 1: torque bolts 1 thru 6 (26 Ft/Lbs & 90 degree turn) Step 2: torque bolts 7 & 8 (15 Ft/Lbs & 90 degree turn) Step 3: torque bolts 9 & 10 (22 Ft/Lbs & 90 degree turn) Recheck final torque in sequence *** CAUTION *** This engine uses "Torque To Yield" (TTY) head bolts that means they permanently stretch during the initial installation. New head bolts must be used when cylinder head is replaced or re-installed in order to obtain proper torque. 3.1 liter V6 Torque sequence--> ' 6 2 3 7 ' ' 5 1 4 8 ' Step 1: torque bolts in sequence to 33 Ft/Lbs Step 2: turn an additional 90 degrees Recheck final torque in sequence *** CAUTION *** This particular engine uses "Torque To Yield" head bolts(TTY) (that means the bolts permanently stretch during the initial installation.) You MUST use NEW head bolts when replacing or reinstalling the cylinder head in order to obtain the proper torque.

If you need further help, reach me via phone at https://www.6ya.com/expert/tasa_06404e20147f8840

2002 ford Taurus se v-6 head bolts torque and sequence

hope this helps,

Torque sequence --------- front ' 6 1 3 7 ' of ' ' engine ' 8 4 2 5 ' --------- Step 1: torque bolts in sequence to 37 Ft/Lbs Step 2: torque all bolts in sequence an additional 120 degrees Step 3: torque bolts 1,2,3, & 4 an additional 30 degrees recheck final torque in sequence *** CAUTION ***engine uses Torque To Yield head bolts (TTY) thatpermanently stretch during the initial installation.New head bolts must be used when cylinder head isreplaced or re-installed to obtain proper torque.
always torque from center
Tighten each bolt an additional 90° in sequence.

These are the torque valies and sequences for your engine
Torque in 2 steps [1st (33-41 ft-lbs),
2nd (63-73 ft-lbs)]


Torque sequence: (for each bank)
------------
6 4 2 8

5 1 3 7
------------
Good luck and please rate this solutuon

Torque sequence: ----------------- there are two rows of fasteners and you need to start with the middle 2 fasteners first and then work your way toward the front and back in steps. Step 1: torque head bolts #1,2,3,4,5,6,7, & 9 in sequence to 10 Ft/Lbs Step 2: torque head bolts #1,2,3,4,5,6,7, & 9 in sequence to 20 Ft/Lbs Step 3: torque head bolts #1,2,3,4,5,6,7, & 9 in sequence to 29 Ft/Lbs Step 4: turn all head bolts in sequence an additional 90 degrees Step 5: turn all head bolts in sequence an additional 90-degrees recheck final torque in sequence. Fasteners are supposed to be replaced if they are removed since they are torque-to-yeild fasteners.

7 - 5 - 1 - 3 - 10
front
9 - 4 - 2 - 6 - 8

Head Bolts
Torque sequence --------- ' 6 2 3 7 ' ' 5 1 4 8 ' --------- Step 1: torque in sequence to 33 Ft/Lbs Step 2: turn an additional 90 degrees recheck final torque in sequence *** CAUTION ***engine uses Torque To Yield head bolts (TTY) that permanently stretch during the initial installation.New head bolts must be used when cylinder head is replaced or re-installed to obtain proper torque.Always coat bolt threads with the proper sealant.
The Intake Bolt Torque 10 Foot pounds (Final torque)
Note:to torque bolts & nuts, start in center using crisscross pattern working outward

1978 - 1980 FORD FESTIVA 1.6L 65-70 Foot pounds (Final torque)
Torque sequence 9 3 1 5 7 8 6 2 4 10 Step 1: torque to 5 Ft/Lbs Step 2: torque to 20-30 Ft/Lbs Step 3: torque to 50-55 Ft/Lbs Step 4: torque to 65-70 Ft/Lbs Recheck final torque in sequence


1988 - 1993 F0RD FESTIVA 1.3L Torque sequence front of engine 8 4 1 5 9 7 3 2 6 10 Step 1: torque to 35-40 Ft/Lbs Step 2: torque to 56-60 Ft/Lbs Recheck final torque in sequence

2011 FORD FESTIVA 1.6L NO TORQUE SPECS AVAILABLE THERE IS NO FORD FESTIVA MANUFACTURED IN 1998 ALSO NO FORD FESTIVA MANUFACTURED WITH A 1.5L ENGINE
HOPE THIS HELPS YOU

Torque sequence:
------------
6 4 2 8

5 1 3 7
------------
Step 1: Torque from 47-53 Nm (35 to 39 Ft/Lbs)
Step 2: Back off all bolts 360
Step 3: Torque from 27 -33NM (20 to 24 Ft/Lbs)
Step 4: Torque rotate 85-95
Step 5: Torque rotate additional 85-95