Power steering pump removal 2001 sunfire gt , do

sounds like you should junk it,so many questions, 1997 sunfire gt shifter cable Bing images

--get your complete install cd-ebay -I have a 2001
You'll probably need it $6 mine

First you need to remove the belt and check all the pullies to include the acceseries (A/C, Power Steering pump, Alt.) If they are all free moving and not worn then replace the belt and check the tention. Also if a belt is wet or has oil on it this will cause noise as well.

1. Remove serpentine belt

2. loosen power steering pressure and return hoses

3. Remove nut from pressure line mounting on alternator bracket

4. remove power steering pump mounting bolts.

5. Lift pump assembly from engine mounting and remove hoses.

6. Reverse order to install. Fill and bleed system.

NOTE: A new or rebuilt power steering pump will most likely not come with a pulley attached. You will need a power steering pulley remover/installer tool to transfer the pully from the old pump to the new one.

4.2L Engine

1. Remove the air cleaner assembly.
   
2. Remove the drive belt.
   
3. Install a drain pan under the vehicle.
   
4. Disconnect the power steering pressure hose from the power steering pump.
   
5. Disconnect the power steering cooler hose from the power steering pump.
   
6. Disconnect the wiring harness from the wiring loom on the power steering pump.
   
7. Remove the power steering pump mounting bolts.
   
8. Remove the power steering pump.
   
9. Remove the power steering pump pulley.
   
10. Remove the power steering pump pulley using Power Steering Pump Pulley Remover tool no. J 25034-C, or equivalent.
    

The procedure is as follows:--- 1) Locate the power steering pump on the driver's side of the motor, which is mounted in front of the engine, near the top.2) You will see a fill spout coming out of the pump with a cap on it that says "power steering fluid."
3) Remove the negative battery cable from the battery
4) Remove the cap from the power steering pump,allow the fluid to drain into the pan.
5) Loosen the bolts that hold the power steering pump to the engine block with a socket wrench. Once the pump is loose, remove the belt from the pulley on the power steering pump. Remove the pump from the engine compartment.
6) Insert new power steering pump in reverse. 7) Reattach the power steering hoses and verify they are secure. Fill the new power steering pump with fluid to the full line shown on the dipstick on the back of the cap for your power steering pump. Place the cap back on the power steering pump.

Thanks. Keep updated for any more query. You can rate this solution and show your appreciation

take everything around your water pump of and use a metric 10 box end wrench

Removal & Installation

1.6L Engine
A/C Compressor Belt

1. Disconnect the negative battery cable.
2. Loosen the A/C compressor mounting bolts.
3. Pivot the A/C compressor towards the engine in order to relieve the tension on the belt.
4. Remove the A/C compressor drive belt from the pulleys.

To install:

1. Properly route and install the A/C compressor drive belt on the A/C compressor, the power steering (if equipped), and the crankshaft pulleys.
2. Adjust the A/C compressor drive belt to obtain 6-9 mm (0.24-0.35 in) deflection.
3. Tighten the A/C compressor mounting bolts to 13-20 f t. lbs. (18-28 Nm).
4. Connect the negative battery cable.

Alternator Belt

1. Disconnect the negative battery cable.
2. Remove the power steering pump and the A/C compressor drive belt.
3. Loosen the generator mounting bolts.
4. Pivot the generator towards the engine and remove the accessory drive belt.

To install:

1. Properly route and install the generator drive belt on the pulleys.
2. Adjust the alternator drive belt to obtain 6-8 mm (0.24-0.32 in) deflection for a used belt or 5-6 mm (0.20-0.24 in) deflection for a new belt.
3. Tighten the generator mounting bolts to 17 ft. lbs. (23 Nm).
4. Install the power steering and the A/C compressor drive belt.
5. Connect the negative battery cable.

Power Steering Pump Belt

1. Disconnect the negative battery cable.
2. Loosen the power steering pump mounting bolts.
3. Pivot the power steering pump towards the engine in order to relieve the tension on the belt.
4. Remove the power steering pump drive belt from the pulleys.

To install:

1. Properly route and install the power steering pump drive belt on the power steering pump and the crankshaft pulleys.
2. Adjust the power steering pump drive belt to obtain 6-9 mm (0.24-0.35 in) deflection.
3. Tighten the power steering pump mounting bolts to 22 ft. lbs. (30 Nm).
4. Connect the negative battery cable.

yes

REMOVAL

1. Remove ground terminal from battery.
2. Remove pulley belt cover bracket.

1. Loosen lock bolt and slider bolt and remove power steering pump drive V-belt.
2. Disconnect connector from power steering pump switch.

1. Disconnect pipe C and suction hose from oil pump. CAUTION:

• Do not allow fluid from the hose end to come into contact with pulley belt.
• To prevent foreign matter from entering the hose and pipe, cover the open ends of them with a clean cloth.

1. Remove bolts which install power steering pump bracket.

1. Place oil pump bracket in a vise, remove two bolts from the front side of oil pump. CAUTION: Do not place oil pump bracket directly in the vise; use soft pads and hold oil pump lightly to protect the pump.

1. Remove socket from oil pump.
2. Remove bolt from the rear side of oil pump.