I own 1994 Acura Integra with a 5 speed manual transmission that recently started to develop a gear whine between shifting 1st to 2nd gears and 3rd gears--less so between 4th and 5th gears. What do you think is the cause? Have I run low on manual transmission fluid? Where is the filler bolt? Thanks, Chester Brezniak

Go for the manual they are easier ti repair.

How to adjust 3 speed column shifter - YouTube

? 9:53
https://www.youtube.com/watch?v=2TCHzIvAvRQ
Mar 6, 2014 - Uploaded by luke Fugate
This is a video to show you how to adjust a Three speed on the column to ... It's great not having to wind the engine and transmission just to take off in 2nd or 3rd gear. ... It was ALWAYS getting stuck between 1st and 2nd gear. .... 1977 c10 3 On The Tree ' How to Drive a 3 Speed Column Shift - Duration: ...

Diagnose Automatic Transmission

www.aa1car.com/library/2002/bf90222.htm

All they know is that they put their gear selector in "D" for Drive and their vehicle ... But when internal problems cause the transmission to act up, it takes a fair amount .... In Chrysler three-speed automatics, changing the fluid to ATF+3 can also help ...kickdowns to get the transmission to downshift to 1st from 2nd or 3rd gear.

Manual transmission - Wikipedia, the free encyclopedia

https://en.wikipedia.org/wiki/Manual_transmission

Wikipedia1 Overview; 2 Unsynchronized transmission; 3 Synchronized transmission; 4 Internals.... gear speeds by blipping the throttle when shifting from 2nd into 1st. ... In a synchromesh gearbox, to correctly match the speed of the gear to that of the ... Even in transmissions that do not feature direct drive, it's an advantage for the ...

When do you use the 1,2,3 gears on an automatic car ...

https://www.reddit.com/.../when_do_you_use_the_123_gears_on_..

05 Chrysler pacifica is a 4 speed automatic, next time buy a car with a 5 speed automatic

shot the tranny need vw bug or viper

Sounds like your transmission is in limp mode. This is a fault mode in which the transmission either loses electrical power or the PCM deactivates all of the electronics. The transmission will default to max line pressure. The driver will have Reverse and 3rd, with manual 2nd available by putting the gearshift in 2 or 1 (doesn't matter). 1st, 4th, and TCC lockup will not be available. It will not hurt the car to drive it like this for short periods, but use manual 2nd to get the car moving, and be aware that the trans will generate more heat than normal while operating in limp-home mode due to increased torque converter slippage during 2nd gear starts and no lockup in 3rd gear.

The other from what you described, trans shifts 2nd to 3rd by itself in D or OD and locks the converter : ShiftA solenoid failed. Easy fix in the pan. Or a wiring problem from PCM to trans.. or PCM.

Thank you for using fixya and have your Safari scanned for the DTC codes that would indicate what issues your transmission is having to put you in to limp mode.

yes you are right but they do not sell the pieces ,dealer only and exchange gearbox been their done it ,no teashirt just scrapped the car

that is a linkage problem

What you need to check is the transmission release bearing because if there is a clearance on the release bearing you will encounter this problem and also check the transmission oil.

I’m happy to assist further over the phone at https://www.6ya.com/expert/ramy_d9e7ebea3891f482

The 1st thing to do is have a test run on the transmission control module to see if any trouble codes are present, next have you ever serviced the transmission, fluid and filter change, should be done at 60,000 miles, on occasion this can cure problems like yours.