1994 Jeep Grand Cherokee Logo
Anonymous
Anonymous Posted on Dec 28, 2009
Answered

How do I check the fluid in the bell housing on a 1994 Jeep Grand Cherokee?

Answer This Question

1 Answer

Anonymous

Level 2:

An expert who has achieved level 2 by getting 100 points
All-Star:

An expert that got 10 achievements.
MVP:

An expert that got 5 achievements.
Vice President:

An expert whose answer got voted for 100 times.

  • Expert 265 Answers
  • Posted on Dec 28, 2009
Anonymous
Expert
Level 2:

An expert who has achieved level 2 by getting 100 points
All-Star:

An expert that got 10 achievements.
MVP:

An expert that got 5 achievements.
Vice President:

An expert whose answer got voted for 100 times.

Joined: Nov 27, 2009
Answers
265
Questions
5
Helped
104187
Points
791

The fluid that is inside of your torque converter, which is located in the bell housing is your transmission fluid.. If your tranny fluid level is good, then the fluid inside of your torque converter is good...Now if you are leaking fluid from that area, it could be either your front seal that is inside the bell housing, or your rear main oil seal......

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

0helpful
1answer

Where us the crank shaft sensor and how do I replace it on a 1994 grand jeep Cherokee 5.2 lt
The sensor is located under the hood, rear engine area, passenger side of transmission bell housing, mounted on bell housing. The sensor extends into the housing where it uses the flywheel teeth to sense crankshaft position. Here is a picture of the sensor.



25919504-xy2b1ep4azxtiqpd5mnkcpdl-4-0.jpg
Read full answer
Oct 22, 2015 • Jeep Cars & Trucks
0helpful
1answer

Bell House Bolts on a 94 Jeep Grand Cherokee
Check your motor mounts on the sides of the engine. Make sure the mount brackets on the engine block are still in place.
Read full answer
Dec 11, 2012 • 1994 Jeep Grand Cherokee
0helpful
1answer

2002 jeep grand cherokee wont reverse when in gear. hear it get into gear but wont move...
first check fluid is full by starting the engine have it blocked put in in nutral( to fill the bell houseing ) then check fluid level, more than likely you need to add fluid exspecally if your checking it in park with engine on or off park gives you a false reading on the dip stick
Read full answer
Jul 31, 2011 • 2001 Jeep Grand Cherokee
0helpful
2answers

My 1996 jeep limited grand cherokee wont start up. It turs over, but wont start
Fuel, fire and exhaust. Pull a plugwire and check for spark. If it is firing check fuel system for pressure.
Read full answer
Jun 24, 2011 • 1996 Jeep Grand Cherokee
0helpful
1answer

1994 jeep cherokee turns over , no spark and won't start???
90% of the time it will be the crankshaft sensor, the sensor sit on top on the transmission bell housing, you can get to it from the drivers side under the hook, there will be a harness running to it from the top over by the injector' rail, going down the back.
Read full answer
Aug 23, 2010 • 1994 Jeep Grand Cherokee
2helpful
1answer

Will not start but turns over! replaced fuel pump and relay.
check to see if you have any spark at the spark plugs. if not then it may be the crank sensor, it's located in the back of the engine at the bell housing
Read full answer
Apr 20, 2010 • 1994 Jeep Grand Cherokee
1helpful
1answer

1993 Jeep Grand Cherokee - V6 engine with a Automatic 4-speed Transmission. Unit will not shift out of 1-2 speed into 3-4 gear. I have checked shift linkage - is OK & TV linkage OK. Is there a vacuum...
The only thing that you can do is check the trans fluid.Start car,run it through all gears and end in neutral.Handbrake on.Now check the trans fluid level.Make sure engine is warm.If needed add fluid.If this is not the problem,a tranny expert is the go.There is not a lot anyone can do with an auto trans at home.Hope this helps
Read full answer
Jan 13, 2010 • 1993 Jeep Grand Cherokee
5helpful
2answers

What oil is used in a 1994 Jeep Grand Cherokee
Use Dexron® II or ATF Plus/Type 7176 automatic transmission fluid (or their superceding fluid type).
Read full answer
Jun 06, 2009 • 1994 Jeep Grand Cherokee
1helpful
1answer

93 Jeep Grand Cherokee Won't start
The crankshaft position sensor was seriously problematic in those old jeeps. It's located towards the top of the bell housing slightly to the driver's side I think.
Read full answer
Apr 15, 2009 • 1994 Jeep Grand Cherokee
0helpful
1answer

1994 jeep grand cherokee. put in gear will not move.
torque converter
Read full answer
Apr 06, 2009 • 1994 Jeep Grand Cherokee
Not finding what you are looking for?

View Most Popular

1994 Grand Cherokee

  • Cars & Trucks

Related Question

Where us the crank shaft sensor and how do I replace it on a 1994 grand jeep Cherokee 5.2 lt

  • Jeep Cars & Trucks

Related Topics

288 views

Ask a Question

Usually answered in minutes!

Popular Questions

GAUGES GO CRAZY AND SOMETIMES VEHICLE WON'T START

2002 Jeep Grand Cherokee

2007 JEEP GRAND CHEROKEE. TRANSMISSION OVER TEMP

2007 Jeep Grand Cherokee Overland

Fuse panel diagram for 2002 Jeep Grand Cherokee

2002 Jeep Grand Cherokee

2007 Jeep Grand Cherokee won't CRANK - battery is fine.

2007 Jeep Grand Cherokee Overland

Firing order for a Jeep

Jeep Grand Cherokee Cars & Trucks

Check Out the Latest Top Trucks Report!
Check Out the Latest Top Trucks Report!

View all Fixya Reports

Top Jeep Experts

ZJ Limited
ZJ Limited

Level 3 Expert

17989 Answers

Thomas Perkins
Thomas Perkins

Level 3 Expert

15088 Answers

john h

Level 3 Expert

29494 Answers

Are you a Jeep Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

JPG Manual
94audionoamp.jpg. user-manual-1994...

1994 Grand Cherokee

Loading...