Serpentine belt diagram for a 4.3 engine

Question edited for clarity, spelling and add maker.

Shown in the link

https://www.google.com/search?q=2007+Ford+Mustang+V6+serpentine+belt+diagram

Service manual

https://cardiagn.com/2005-ford-mustang-service-repair-manual-pdf/

..

search online for diagrams, avail yourself of internet search. Diagram is usually found under hood. found less than 10 seconds


2010 FORD Fusion Serpentine Belt Diagram for 4 Cylinder 2 5 Liter Engine...

1992 Mercedes 300SD 3 4 liter engine serpentine belt diagram Google Search

Diagram reference number 1 in the image below:
"" Fitment: 2006 SUBARU B9 TRIBECA - 4 door

Application Notes:

Category: Electrical. Charging and Starting

SubCategory: Alternator / Generator and Related Components

Position: General

Part Number: 809221090


This is a Serpentine Belt that fits the 2006 SUBARU B9 TRIBECA - 4 door with the EZ30D engine. The Serpentine Belt is designed by SUBARU to be part of the Electrical. Charging and Starting-Alternator / Generator and Related Components. The Serpentine Belt has a position on the vehicle of General. The 2006 SUBARU B9 TRIBECA Serpentine Belt is a factory made SUBARU OEM part and it comes with a 12 month 12.000 mile warranty (parts only). Do not be fooled by an aftermarket SUBARU B9 TRIBECA Serpentine Belt! Buy a factory SUBARU part and receive peace of mind!
This factory part has a part number of 809221090. "

Pop the hood of the car and locate the serpentine belt routing diagram. The diagram on the 2003 Chevrolet Impala is on top of the fan shroud. The diagram will be a picture of all of the accessory pulleys and how the serpentine belt is routed among the pulleys. This diagram will give you the exact direction for routing the new belt onto the pulleys. If you cannot find a serpentine belt routing diagram, take a notepad and pen and draw out the exact routing diagram of the old belt across the pulleys.

2 Locate the serpentine belt tensioner. It is located below the alternator on the left front side of the engine. The tensioner on the 3.4 liter, 3.5 liter and the 3.9 liter engines will require a 3/8 ratchet to release the belt tensioner. The 3.8 liter engine will require a ratchet and a 15 mm socket for the belt tensioner. Rotate the belt tensioner clockwise to loosen and remove the belt from the belt tensioner pulley.

3 Slide the old belt from the belt tensioner pulley. Remove the belt from the remaining pulleys and pull the belt from the engine compartment.

4 Route the new belt across the crankshaft pulley first. The crankshaft pulley is the big pulley on the bottom of the engine in the center. Then route the serpentine belt across the remaining pulleys as directed by the serpentine belt routing diagram. Leave the belt tensioner pulley for last.

5 Rotate the belt tensioner clockwise again to relieve the tension and slide the new belt across the top of the belt tensioner pulley. Release the belt tensioner and the belt will tighten up as the tensioner applies pressure to the belt. Make sure the new belt is properly seated in all the pulleys.

6 Crank the engine and inspect the belt again to make sure that it stays seated in the pulleys.

Read more: How to Replace a Serpentine Belt on a 2003 Chevrolet Impala ' eHow.co.uk http://www.ehow.co.uk/how_6120665_replace-belt-2003-chevrolet-impala.html#ixzz1Yi6QLAjb

1. 1 Check to ensure the Sienna's engine is cold, then make sure the Sienna is in park, the ignition is in the off position and the key is removed from the ignition to prevent any possibility of the engine engaging during the serpentine belt replacement.
   
2. 2 Open the hood and locate the serpentine belt routing diagram sticker on the side of the engine casing. Study it for a moment before removing the existing belt. It is essential the new belt be installed exactly as the diagram indicates.
   
3. 3 Find the tensioner pulley, the main pulley that controls the serpentine belt, and fit a 1/2-inch socket wrench over the self-tensioner on the outside of the pulley.
   
4. 4 Pull the wrench to the left to move the pulley forward, which loosens the belt, then remove the belt.
   
5. 5 Compare the old serpentine belt with the new, replacement belt for length, width and number of grooves on the belt's underside. Be certain the replacement belt is the right part.
   
6. 6 Fit the new belt on to each pulley according to the serpentine belt routing diagram on the manufacturer's sticker, or according to the drawing made prior to removing the old belt. Fit the new belt on to the tensioner pulley last, again applying pressure on the pulley's self-tensioner with the half-inch socket wrench to loosen the pulley.
   
7. 7 Release the pressure on the self tensioner and allow the tensioner pulley to ease back into place, thereby tightening the new serpentine belt with the appropriate tension.
   
8. 8 Remove the wrench and close the hood.
   

Thank you and good luck,
Lee

You didn't list your motor size so please pick the applicable diagram:


Accessory serpentine belt routing—4.8L, 5.3L & 6.0L engines


Accessory serpentine belt routing—5.7L engines with A/C


Accessory serpentine belt routing—5.7L engines without A/C


Accessory serpentine belt routing—6.5L Diesel engines


Accessory serpentine belt routing—7.4L engines


Accessory serpentine belt routing—8.1L engines

Good morning! I am enclosing a serpentine belt routing diagram to aid in the installation of your serpentine belt. There are 4 different engine possibilities but i have enclosed all. The serpentine belt tensioner is released by rotating in a clockwise direction as shown in the diagrams. Engine configuration will determine what tools you need but the installation is relatively easy to do. Have a great day!

Here are links to the diagram...

If your engine is the 2.3L 4 cyl... http://www.gates.com/common/part_locator/view_diagram.cfm?id=S7042

If your engine is the 3.0L V6... http://www.gates.com/common/part_locator/view_diagram.cfm?id=S6036