2000 s-10 ZR2 3sp w/Od automatic transmission shifts hard from 1st to 2nd on hot days or after driving 30+ miles. Been this way for 4 years or better. Now has 141,000 miles. I know these transmissions are known to break around 100K or more. What part of the transmission is actually the trouble ( weak )? I would like to fix it myself. Thanks

You more than likely need to have the transmission overhauled

Governor pressure controls the 1st and 2nd shifts. After that is the 3 and 4 solenoids. you would need to look at the pressure when driving(takes a scanner). pressure is 20 to 30 PSI from 1st to 2nd, depends on acceleration. After that the pressure will jump to 100+ psi. Did you replace the governor solenoid and sensor? They are on the passenger side of the transmission and sit in a block that detaches from the valve body.

05 Chrysler pacifica is a 4 speed automatic, next time buy a car with a 5 speed automatic

Well go get your car fixed by a mechanic or it something might be jammed inside

Hello
The Engine and Automatic Transmission (not applicable to manual transmissions) in this vehicles drive train are fully electronically controlled by a computer called the PCM and TCM (Power Train Control Module, Transmission Control Module). When a problem like this or other drive-ability related problems occurs the computer stores a record of the problem (there are of course some exceptions to this, like the fuel pump, engine coolant temperature sensor and MAF sensor for instance) in the form of a fault code in its memory, to read these fault codes you must have the systems memory scanned with a special tool. Once the fault code(s) are read you then must perform the appropriate diagnostic testing to find and resolve the problem(s) DO NOT REPLACE ANY PARTS UNTIL A TRAINED TECHNICAIN HAS DIAGNOSED THE PROBLEM TO AVOID SPENDING YOUR HARD EARNED MONEY ON PARTS THAT MAY NOT CORRECT THE PROBLEM. Also always check fuel pressure for correct spec for your make and engine type.

For Automatic transmission problem,click the link below:---- Automatic transmission troubleshooting:----

http://howtobyme.blogspot.com/2011/11/automatic-transmission-will-not-go-into.html

---------
Automatic transmission shift lever issues?-------

http://technoanswers.blogspot.com/2012/01/automatic-transmission-shift-lever-hard.html

-----------
AUTOMATIC TRANSMISSION FLUID LEVEL? --

http://schematicsdiagram.blogspot.com/2011/07/how-to-check-automatic-transmission.html

--------------

AUTOMATIC TRANSMISSION FLUID AND FILTER?

http://schematicsdiagram.blogspot.com/2011/07/how-to-change-automatic-transmission.html

-----------
Transmission fault light on car dash?

http://schematicsdiagram.blogspot.com/2011/12/transmission-fault-light-on-car-dash.html

--------
Transmission shifting problem?

http://schematicsdiagram.blogspot.com/2012/01/transmission-shifting-problem-on-toyota.html

--------
Transmission Slips out of 2nd gear?

http://repairhelpcenter.blogspot.in/2012/02/transmission-slips-out-of-2nd-gear.html

-----------
OD light flashing and transmission fluid leaking?

http://repairhelpcenter.blogspot.in/2012/02/od-light-flashing-and-transmission.html

----------
Why Transmission fluid leaks near radiator?

http://repairhelpcenter.blogspot.in/2012/02/transmission-fluid-leaks-near-radiator.html

----------
Transmission fluid leaking?

http://technoanswers.blogspot.in/2012/02/ford-windstar-transmission-fluid.html

-------------
****** wont go in reverse?

http://technoanswers.blogspot.in/2012/02/dodge-neon-wont-go-in-reverse.html

-------------
Automatic transmission will not go into reverse?

http://technoanswers.blogspot.in/2012/02/dodge-automatic-transmission-will-not.html

----------
Transmission is making buzzing noise?

http://technoanswers.blogspot.in/2012/02/transmission-is-making-buzzing-noise.html

-----------

This will help.

Thanks.

1-2 shift is delayed and harsh, may not shift into OD: Check TPS for smooth and linear electrical response over the entire range of motion. If not, replace or EPC (Electronic Pressure Control) solenoid failed. Easy fix in pan. Fix as soon as possible or hard parts will eventually break. Start with the simple and check the transmission fluid level and condition.Secondly, put a line pressure gauge (or visit a local trans shop) on the pressure test port and go for a drive to verify proper line pressure. Base pressure at idle in P,N,OD should be around 70psi and around 140psi in R. Max line pressure should be at least 190psi at WOT in 1st or 2nd, 225psi is optimum. If base pressure is low, trans or pump is worn out. If max pressure is low, check EPC solenoid. If reverse is slow to engage, and line pressure does not come up to at least 130psi in reverse, replace the boost valve with a Transgo 0.500" boost valve (easy fix in pan).
No 1st or 4th available; trans shifts 2nd to 3rd by itself in D or OD and locks the converter : ShiftA solenoid failed. Easy fix in the pan. Or a wiring problem from PCM to trans.. or PCM.

Good luck and keep me posted.

That should be the L60-4 truck version
Have the sedan version, 93 Caprice.
That was the first year of the new electronic shifting transmission.
Especialy when cold she will shift hard, but it's normal.
But that depends on what you call normal.
I have gotten used to it over the last 17 years.

make sure you maintain trans fluid, may be low or very dirty. get serviced,

you should first check gear box oil ,level and clean filter.lee