01 dodge dekota 4.7L misfire on cylinder one only

If you're still experiencing a cylinder 2 misfire in your 2013 Dodge Avenger 3.6L V6 after replacing the coils, spark plugs, and wires, there are a few potential causes to consider: 1. Fuel Injector Issue: A malfunctioning or clogged fuel injector can cause a misfire in a specific cylinder. Check the fuel injector for cylinder 2 and ensure it is functioning properly. It may require cleaning or replacement. 2. Compression Problem: Low compression in cylinder 2 can lead to a misfire. Perform a compression test to check the compression levels in all cylinders. If cylinder 2 shows significantly lower compression, it may indicate issues with the valves, piston rings, or cylinder head gasket. 3. Ignition Timing: Incorrect ignition timing can cause misfires. Ensure the ignition timing is set correctly according to the manufacturer's specifications. 4. Vacuum Leak: A vacuum leak near cylinder 2 can disrupt the air-fuel mixture and lead to a misfire. Inspect the vacuum lines and intake manifold for any leaks or loose connections. 5.Engine Control Module (ECM) Issue: A faulty ECM can incorrectly trigger a misfire code. Consider having the ECM scanned for any error codes or anomalies related to cylinder 2.

Question edited for clarity.
Question moved from 'Speed Computers', to Pontiac G5.

The way to find which item is faulty is easy.

Clear the code

Move the plug from cylinder 2 and put it in cylinder 4. Run the car. Is the misfire still on 2 or has it moved to 4. Yes? the plug is faulty. No? Next test.

Clear the code
Move the coil pack from cylinder 2 and put it in cylinder 4. Run the car. Is the misfire still on 2 or has it moved to 4. Yes? the coil pack is faulty. No? Next test.

Same test for the injector.

If the misfire remains on 2 you need an auto-electrician with a pro grade scan tool computer which analyses every sensor and every module.

MA2304 - 5 injectors 4 solenoid valve, low voltage
Best I can do.

neither if if ran fine for a few days after your repairs
misfires are more likely from problem injectors, low fuel pressures or injector wiring problems
use a couple of vans of quality injector cleaner first

2005 Dodge Grand Caravan 3.8L engine misfire on cylinder 5.

answers.edmunds.com > Edmunds Answers

Aug 14, 2012 - MIL on; cylinder 5 misfire; most noticeable at idle in gear ... This could be caused by an EGR valve that is sticking partly open and not closing ...

OBD-II Trouble Code: P0305 Cylinder 5 Five Misfire Detected

www.obd-codes.com/p0305

A P0305 code means that the the car's computer has detected that one of the engine'scylinders is not firing properly. In this case it's cylinder #5.

ODB Code P0305- Misfire in #5 Cylinder - 2008 Dodge ...

repairpal.com > ... > Grand Caravan > 2008 Dodge Grand Caravan

Feb 22, 2011 - ... do something with a misfire in the #5 cylinder of my V6 4.0L engine. ... ODB Code P0305- Misfire in #5 Cylinder on 2008 Dodge Grand Caravan .... My2005 dodge grand caravan jerks when it shifts into gear what could it be.

My Dodge Grand Caravan has a Cylinder 5 Misfire,? ' Yahoo An

If you had code P0305, I don't know why they would have done anything to the #2 cylinder but if they have already replaced the plugs, wires and injector; here are a few more items to check:
1) Check connections from ECM. Look for any corrosions or bent/broken pins.
2) Check the fuel line pressure
3) Check the engine compression
4) And if the above are good, then you will probably have a defective ECM

Try swapping the coil packs around - like swap #1 with #2, and swap #6 with #5, see if the misfires MOVE with the coil packs swapped to the new cylinders or if they stay with the cylinders. If they move with the coil packs, the new coil packs are bad. If they stay with the cylinders, there's a problem with those cylinders. You DID replace that camshaft sensor, right?

Have you checked your #1 and #6 injectors?

For engine misfiring problem check the help links mentioned below. Click the link below to go through the troubleshooting procedure :---- No pulse to injectors? http://technoanswers.blogspot.com/2012/01/no-pulse-to-injectors.html
---------How to Test and Replace Fuel Injectors? http://repairhelpcenter.blogspot.com/2011/11/how-to-test-and-replace-fuel-injectors.html
---------

How to Replace a Fuel Injector
http://schematicsdiagram.blogspot.com/2011/07/how-to-replace-fuel-injector.html
--------
Engine misses and truck jumps? Hard to down shift? Issue with high gear only? http://technoanswers.blogspot.in/2012/02/engine-miss-and-truck-jumps-hard-to.html

-----------
Bad miss at idle?

http://technoanswers.blogspot.com/2012/01/bad-miss-at-idle.html

-----------
While stop engine idles like cylinder missing?

http://schematicsdiagram.blogspot.com/2012/01/while-stop-engine-idles-like-cylinder.html

------------
Engine Misfire codes for car?

http://schematicsdiagram.blogspot.com/2011/12/engine-misfire-codes-on-chevrolet.html
Engine Misfire codes?

http://schematicsdiagram.blogspot.com/2011/12/engine-misfire-codes-on-chevrolet.html

--------------
Misfire on cylinder 4?

http://schematicsdiagram.blogspot.com/2011/12/misfire-on-cylinder-4.html

-----------
Oil on spark plugs and car misfires?

http://technoanswers.blogspot.in/2012/02/oil-on-spark-plugs-and-car-misfires.html

----------

This will help.

Thanks.

All these codes indicate you have a misfire on cylinder number 5.
P1399/P0300 - Random/Multiple Cylinder Misfire Detected
P0305 - Cylinder #5 Misfire Detected

Causes:
- Improper spark plug at cylinder #5
- Insufficient compression at cylinder #5
- Incorrect fuel pressure
- The injector circuit is open or shorted at cylinder #5
- Fuel injector #5 may be faulty
- Intake air leak at cylinder head

Solutions:
- Perform Injector Service
- Replace Spark Plug #5
- Replace Injector #5
- Replace Ignition Coil #5

CODE 27 - Injector Control Circuit, output driver does not respond properly to the control signal

Code 27 MIL light options: OBDII
P0201 - Injector #1 Control Circuit
P0202 - Injector #2 Control Circuit
P0203 - Injector #3 Control Circuit
P0204 - Injector #4 Control Circuit
P0205 - Injector #5 Control Circuit
P0206 - Injector #6 Control Circuit

CODE 43 - Cylinder Misfire, or Ignition Primary Circuit

CODE $# MIL options: OBDII
P0300 - Multiple Cylinder Misfire
P0301 - Cylinder #1 Misfire
P0302 - Cylinder #2 Misfire
P0303 - Cylinder #3 Misfire
P0304 - Cylinder #4 Misfire
P0305 - Cylinder #5 Misfire
P0306 - Cylinder #6 Misfire
P0351 - Ignition Coil #1 Primary Circuit
P0352 - Ignition Coil #2 Primary Circuit
P0353 - Ignition Coil #3 Primary Circuit