I accidently topped off my 2009 Ford Fusion coolant system with wipper fluid. Is this a serious problem?

those are not codes --before using a scanner read all the instructions on proper use -- rescan and the 7eB's are advising that you have a code and to continue to the next screen to get code[s]

WHAT IS A COMPASS ERROR FOR A 2009 FORD FUSION ...

www.fixya.com/cars/t16705785-compass_error_2009_ford_fusion

Feb 21, 2013 - WHAT IS A COMPASS ERROR FOR A 2009 FORD FUSION A MESSAGE COMES UP ON MY DASH SAYS COMPASS NO ... SOURCE: I HAVE A2009 FORD FUSION AND IT'S NOT GOING OVER 20 MPH ... Compass data error -- how do i determine my zone-- ... Jan 28, 2010 ' 2007 Ford Edge SEL Plus.

Compass - Ford Fusion Sport - Ford Fusion Forum

www.fordfusionforum.com/topic/9390-compass/

Jan 23, 2013 - Compass - posted in Ford Fusion Sport: 2011 Fusion SEL without navigation screen. Following windshield ... I have recalibrated and reset the compassaccording to the manual instructions (several times) but cannot correct the error. Can anyone help? ... picture of where it is: 2009-08-30_051718_2.gif.

2.3L Engine

Specific to:
Ford Fusion 2008-2009
Mercury Milan 2008-2009

1. Raise and safely support the vehicle.
2. Drain the cooling system.
3. Loosen the 3 coolant pump pulley bolts.
4. Remove the accessory drive belt.
5. Remove the 3 bolts and the coolant pump pulley.
   1. To install, tighten to 15 ft. lbs. (20 Nm).
6. Remove the 3 bolts and the coolant pump.
7. Remove and discard the O-ring seal.
   1. To install, tighten to 89 inch lbs. (10 Nm).
   
   

Fig. Exploded view of the water pump-2.3L engine


To install:

1. To install, reverse the removal procedure.
2. Lubricate the O-ring seal with clean engine coolant.
3. Fill and bleed the cooling system

3.0L Engine

Specific to:
Ford Fusion 2008-2009
Mercury Milan 2008-2009

1. Raise and safely support the vehicle.
2. Drain the cooling system.
3. Remove the coolant pump belt.
4. Using Special tool 303-S455, or equivalent, remove the coolant pump drive pulley.

Fig. Using Special tool 303-S455, or equivalent, remove the coolant pump drive pulley

5, Disconnect the heater hose from the coolant pump.
6. Disconnect the coolant pump-to-engine hose and position aside.
7. Remove the 3 bolts from the coolant pump assembly.
8. Reposition the coolant pump-to-thermostat housing hose clamp and remove the coolant pump and hose as an assembly.



Fig. View of the water pump and related components-3.0L engine

To install:

1. Connect the coolant pump-to-thermostat housing hose and reposition the clamp.
2. Position the coolant pump assembly and install the 3 bolts:
   1. Tighten to 89 inch lbs. (10 Nm).
   2. Tighten the 3 bolts an additional 90 degrees.
3. Connect the coolant pump-to-engine hose and the heater hose.
   NOTE
   Install the coolant pump drive pulley flush with the end of the camshaft.
4. Using Special tools 211-185 and 303-S455, or equivalent, install the coolant pump drive pulley.

Fig. Using Special tools 211-185 and 303-S455, or equivalent, install the coolant pump drive pulley

5. Install the coolant pump belt.
6. Fill and bleed the cooling system.

All warning lights must be taken serious. Even when the light goes on, because the sensor is defect. Ignoring it and not repair this, makes you also get no warning when the system really fails.
Why the light goes on? could be a real error in the ABS system, could be a sensor problem. Impossible to see from here. Please let a tech check what is wrong and don't wait here for an answer like leave it, or remove the bulb, because that would be ridiculous and irresponsible.

you door handle is broken ! 2009 Ford Fusion Replacing inside door handle Happens all the time on newer vehicles , made of plastic !

You never need to top off fluids

If you do- you have a leak to be repaired

Check the vehicles systems for codes,
then google those codes to see the problem

TYPE: OBD & your code

It is going into ETC Failsafe or something

Do not use it at all,you may have converter ruining
cylinder misfires, from bad ignition coils

You add NO WATER to any vehicle

Distilled water & coolant only

Is it green or red? Will not start if the coolant level is too low, you might have a serious cooling system leakage, just fill the cooling system up with water see if it starts, if it does, still need to find the leak, bring it to a mechanic.

Have you checked for vacuum leaks?

You are not driving in first gear are you? Is the park brake on?