Question about 1991 Ford Mustang

2 Answers

I HAVE AN ADJUSTABLE CLUTCH ON MY 91 MUSTANG AND WHEN I LET OUT THE CLUTCH THE CAR REVS HIGH AND TAKES A MINUTE TO GO DO YOU KNOW WHAT CAN BE CAUSING THIS?

Posted by on

  • Anonymous May 11, 2010

    The clutch isn't mechanically capable of increasing the engine's RPM. It's just a symptom of an engine problem. Clarify for me: When you push and hold the clutch pedal all the way down, the engine runs normally but when you release it, it revs up?

×

Ad

2 Answers

  • Level 1:

    An expert who has achieved level 1.

    New Friend:

    An expert that has 1 follower.

  • Contributor
  • 3 Answers

Sounds to me like the clutch disc is shot. Make sure there is a little bit of play in the pedal at the top of travel. If you put your foot on the pedal and there isn't any play at the top then the clutch may not be engaging all the way (and you may have burned up the clutch from the slippage). Good Luck,...ZMANRACINGI HAVE AN ADJUSTABLE CLUTCH ON MY 91 MUSTANG AND - 663a3f6.jpg

Posted on Dec 05, 2009

Ad

  • Level 1:

    An expert who has achieved level 1.

    New Friend:

    An expert that has 1 follower.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Contributor
  • 5 Answers

You can try to adjust the clutch cable... But from what I recall it should have an automatic clutch adjuster... (could be mistakened) Honestly, when clutch slips it time to replace the worn clutch...

Posted on Nov 28, 2009

Ad

1 Suggested Answer

6ya6ya

6ya staff

  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Smoke from bonnet high revs per minute and burned out smell inside - going into gear inside but car not going anywhere...clutch??


possibly but check out the hydraulics or clutch cable first
if it is a cable then it is possible that the cable is jammed and not fully engaging the clutch
if it is hydraulic it is possible that the compensating port in the clutch master cylinder is blocked and not allowing full clutch engagement

Oct 25, 2015 | Vauxhall Cars & Trucks

2 Answers

1998 Honda accord manual transmission revs high, car barely accelerates. What would cause this problem? the clutch was replaced 2 years ago.


You know the clutch is slipping
& continue to drive & ruin that

Now you can do another clutch
service, while your finding the answer
to what your asking

Next car get an automatic & just change
the fluid every 3 years

Mar 07, 2013 | Cars & Trucks

1 Answer

1989 mustang gt starts revs really high then dies


Sounds like the idle control valve. The same thing happened to my Mustang and that was my problem.

1_15_2013_4_59_36_pm.jpg

Jan 15, 2013 | 1989 Ford Mustang

2 Answers

Is clutch adjustable? Engine revs,but barely moves


it's not if you have hydraulic system.
check to see if the clutch pedal is firm and has pressure
start your engine, depress the clutch pedal and put it in gear
if it goes in gear easily and the car won't move then you need clutch

Apr 21, 2010 | 1996 Ford Explorer

1 Answer

2001 Tiburon high rev problem.


Throttle position sensor or idle control sensor. Try cleaning the map or maf and throttle body first.you can get the cleaner at parts stores or walmart. Takes about half an hour.

Sep 13, 2017 | 2001 Hyundai Tiburon

1 Answer

Gears slip


the transmission is fine its the springs in the preasure plate that have shrunk and the clutch needs to be replaced.
I hope this advice helps.
can u rate the advice please

Feb 26, 2009 | 1996 Ford Mustang

1 Answer

91 Explorer revs up but won't go


your clutch is burned out, replace clutch. will it pull in 4 low?

Feb 25, 2009 | 1991 Ford Explorer

1 Answer

My '01 Mustang V6 revs high when in neutral/when changing gears.


sounds more like the IAC, Idle air control valve.. they can be cleaned with carb and choke cleaner gently...

Nov 17, 2008 | 2001 Ford Mustang

1 Answer

CLUTCH ISSUES


you are referring to the clutch master cylinder it takes brake fluid. it is closer to the fender by master cylnder. sounds like you have a release bearing going bad

Sep 15, 2008 | 2004 Ford Mustang

Not finding what you are looking for?
1991 Ford Mustang Logo

Related Topics:

296 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

Marvin
Marvin

Level 3 Expert

85206 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22484 Answers

gerry bissi

Level 3 Expert

4388 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...