Driver side window isnt working but the rest

Check the fuse. If fuses are good, check the battery in the remote. If that is good, try unhooking the negative battery cable for 10 seconds and reconnecting it.

hummm strange
does the master switch have a other door lock button

so central locking and windows dont work as they should

driver side window motor faulty

individual door lock actuator motors not getting power


it is possible the central locking module wont work unless reset to the other cars electronics with the correct scanner

So the passenger side window isnt working ,have you checked for power to the motor and power to the switch ,could the fault be in the rubber boot from the door frame to the door ? damaged cable unless you check these things out first and then explain i cannot possibly tell you what to do

First, if the driver's window is working, there is no need to waste your time looking for fuses. ALL of the windows are powered by the SAME fuse.

The first thing I recommend checking is the window "lock" switch on the master switch. If it is in the "lock" position, none of the other windows will work (it is designed to do that)

Other than that, you need to check for power and ground at all of the other door switches. The BLUE/BLACK wire at each of the switches should have battery voltage anytime the ignition switch is in the ON position. If they do not, the wire is broken between the splice near the driver's door and the right front door. Both the RED and the GREEN wires at each switch should have continuity to ground anytime the master switch is at rest with the "lock" switch in the unlock position (the lock switch breaks these grounds to "lock" the windows and prevent them from being operated).

Just did this procedure I got from coloradofans.com forums:

"any type of power/voltage change seems to trigger this issue

The most common symptom is power locks fail and only the driver window quits, however that is on the extended cab.

Steps to fix and it works every time.

take door panel off driver's door
Disconnect the wiring attached to window and power lock control unit
disconnect battery cables
connect the negative to the positive cable(((NO BATTERY CONNECTED)))
This will act to short residual voltage in the system

5 minutes later
place the key in the ignition and turn to the run position
connect the wiring to the window/lock controller
connect the negative cable to the battery
then the positive
open drivers side door
turn key to the off position((do not remove yet)) you should get a series of dings through speakers telling you the key is still in the ignition
once it begins dinging pull the key out and you should hear the door lock solenoids trigger and the windows should work." - Coloradofans.com forums

Just figured it out and replicated it 3 times..

any type of power/voltage change seems to trigger this issue

The most common symptom is power locks fail and only the driver window quits, however that is on the extended cab.

Steps to fix and it works every time.

take door panel off driver's door
Disconnect the wiring attached to window and power lock control unit
disconnect battery cables
connect the negative to the positive cable(((NO BATTERY CONNECTED)))
This will act to short residual voltage in the system

5 minutes later
place the key in the ignition and turn to the run position
connect the wiring to the window/lock controller
connect the negative cable to the battery
then the positive
open drivers side door
turn key to the off position((do not remove yet)) you should get a series of dings through speakers telling you the key is still in the ignition
once it begins dinging pull the key out and you should hear the door lock solenoids trigger and the windows should work.

Three years and a very unhappy girlfriend who owns the truck. but she's happy now.

It may seam extremely complex this problem however its likely vary simple.What you need to do is fine out what works and what dose not . Dose the keyless work on other doors the battery is G or NG. You also mention the remote starter stopped working and D and P position no longer works correctly with the controls /switches in the drivers side door only' not the other doors ..
The control panel for the locks and window switches are on the arm rest drivers door it tends to get wet rain snow window open over time bad connections /switch contact and that is the point you need to look at first . Get some electrical contact cleaner spray into the switches not to much spillage use a tube or it may damage trim materials .
Then use the controls back and forth if you see any improvement of function starts /then stops any change you found the problem .Its in the door.

you may need to have the body control module reprogramed. I think the dealership is the only ones that can do that.

check for broken wires between door and front fender

THIS REALLY WORKS****** Saved atleast $600 easy
Ok so when you open your driver door there is a black boot that goes from the body of Jeep to the door (inside the Jam when you open door-its visable) Take this loose...inside there is a wire bundle...there was a black and orange wire in there that were both broken....All we did was strip these and reconnect them w/ connector....Voila..windows all roll up and down..interior lights come on and the locks work and the power mirrors....I AM SO HAPPY THAT THIS WORKED SAVED ME SO MUCH $$$$