Cars & Trucks Logo

Related Topics:

Posted on Nov 19, 2009
Answered by a Fixya Expert

Trustworthy Expert Solutions

At Fixya.com, our trusted experts are meticulously vetted and possess extensive experience in their respective fields. Backed by a community of knowledgeable professionals, our platform ensures that the solutions provided are thoroughly researched and validated.

View Our Top Experts

Spinning sound when pushing gas peddle, sitting

Spinning sound in engine when pushing gas peddle, when sitting still or moving.

  • Anonymous May 11, 2010

    what year, model, engine, and where/what area spinning sound comes from?

×

2 Answers

Anonymous

Level 1:

An expert who has achieved level 1.

  • Contributor 1 Answer
  • Posted on Jan 16, 2010
Anonymous
Contributor
Level 1:

An expert who has achieved level 1.

Joined: Jan 16, 2010
Answers
1
Questions
0
Helped
199
Points
1

Mine was low oil, it was making this spinning sound, i added oil and it went away right away.

Anonymous

Level 2:

An expert who has achieved level 2 by getting 100 points

MVP:

An expert that got 5 achievements.

Sergeant:

An expert that has over 500 points.

Champion:

An expert who has answered 200 questions.

  • Expert 226 Answers
  • Posted on Nov 19, 2009
Anonymous
Expert
Level 2:

An expert who has achieved level 2 by getting 100 points

MVP:

An expert that got 5 achievements.

Sergeant:

An expert that has over 500 points.

Champion:

An expert who has answered 200 questions.

Joined: Dec 31, 2008
Answers
226
Questions
1
Helped
137566
Points
618

Try it with the belts off you can start it and see if the spinning noise goes away then it's accessory's like bad alternator or power steering pump but dont run it more than a minute or two or it will start to overheat. and if it still makes spinning noise make sure it's not coming from the transmission /use a broomstick against the engine block near each piston to hear the condition of the pistons if there scored real bad it makes noticable diff noise than a diff piston will make. check the front of the engin the water pump sometimes needs to be replaced because the bearing in it drys up and fails / there sealed bearings in a water pump than go make noise . good luck give you stuff to think about.

Ad

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

0helpful
1answer

Car wont move

Check your throttle cable . sounds like it might be broken
0helpful
1answer

Looses power under a load put in neutral give gas runs good

sound like fuel filter stopped up.if you have distributor type engine your idle speed could be too low and ignition timing off a little.
0helpful
2answers

I cant push my brake peddle down ?

sounds like the break booster or master cylinder. Also maybe a vacumm issue with the break booster make sure the line is hooked from the booster to the engine intake
5helpful
1answer

When push brakes you have to push really hard to make them go in then the truck barely stops. Replaced the MC and bled the brakes now every time push brakes truck acts like its going to die. Brake light...

Sounds like you will have to bleed your brakes again, but thats not the problem og hard brake peddle, need to check your power brake booster, sit right in back of master cylinder, check make sure it has vacum going to it, also to test it with engine off, press on brake peddle three time, then state engine with foot on peddle, peddle should go down a few inches, also with engine of peddle should feel soft for three pumps, if you have none of this , power brake booster is bad.
0helpful
1answer

Car won't start

try this, if the car wont start push the pedal all the way to the floor and hold it ther while you crank. It sounds like you are flooding the car some how. Pushing the pedal to the floor puts the car into clear flood mode and it shuts off the fuel flow. try and see just a suggestion
0helpful
1answer

96 Jeep Grand Cherokee wont go into reverse

chheck your tranny fluid. if it's ok, probably need tranny work done.
0helpful
1answer

I have a 95 Lincoln Continetal and I can't push the gas peddle down without force. When i pull the cable from the engine the peddle moves fine. Also when I try to move the throttle it will not move.

Hi if the cable is moving freely than it will be either the throttle body jammed or the throttle pedal has ceased, also check nothing has got jammed behind or above the pedal, hope this helps
0helpful
1answer

1999 rodeo 6 cyl

hello from what you explained i take it theres no check engine lights on what it sounds like is a basic increase on your idle screw get somone to help push pedal down underhood look to see where gas cable pulls back when gas pedals appled have them release slowly now watch where it stops against a set screw that is your adjustment rpm range should be somewhere between 750-900 rpm depending on vehicle if this doesnt solve most likely tps sensor{ throttle position sensor} goodluck
0helpful
1answer

Break/Gas peddles hit at same time

the Brake pedal is a huge Pedal. Move your foot over.. Be less lazy in your foot placement. Its an 08 so i'm assuming fairly new to you.. Its gotta be different from what your used too. Sit up straight, slide your seat up..move your foot over, and drive. Sleeping is for Beds..
Not finding what you are looking for?

209 views

Ask a Question

Usually answered in minutes!

Top Dodge Experts

ZJ Limited
ZJ Limited

Level 3 Expert

17989 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6988 Answers

Thomas Perkins
Thomas Perkins

Level 3 Expert

15088 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...