How difficult is it to replace ignition cylinder lock. Cylinder was ripped out

Our Professional Tech Jeff provides the answer

• Jeff Armer Nov 03, 2023
• you need a new key an lock cylinder .
• 
  Jeff Armer Nov 03, 2023
  https://www.partsgeek.com/catalog/2004/s...
  

It is a known issue

Ignition cylinder replacement DIY? - SaturnFans.com Forums

SaturnFans.com http://www.saturnfans.com > ... > Vue Tech
Sep 27, 2009 - I have run into the very common notchy/sticy ignition cylinder problem on a 2004 Vue. ... $60 for the Saturn lock cylinder on the Vue is starting ...

2007 Vue--ignition, new housing and keys - SaturnFans.com
Sep 30, 2019
Ignition lock cylinder removal question.... - SaturnFans.com
Mar 5, 2006
Free ignition lock cylinder fix.... - SaturnFans.com Forums
Jul 30, 2010
Ignition Lock Cylinder Replacement 2004 Saturn Ion
Mar 20, 2013
More results from www.saturnfans.com

Saturn Vue Ignition Lock Cylinder Replacement Cost

RepairPal.com https://repairpal.com > estimator > ignition-lock-cylind...
The average cost for a Saturn Vue Ignition Lock Cylinder Replacement is between $139 and $174. Labor costs are estimated between $65 and $82 while parts are ...

Videos

From memory, all ignition locks have a small catch to make removal difficult. There is a small hole you have to press a paper clip or similar into it to release the catch.

Videos. Ignore door locks.

https://www.google.com/search?q=2005+tundra+replace+ignition+lock+cylinder

..

you don't need a video //// on the bottom of the plastic shroud that covers the steering column you will see a hole & inside is a shiny metal button if you don't have the keys you must drill out that button then you will be able to twist the lock cylinder forward to remove it make sure the battery has been disconnected before you rotate the cylinder because the truck will start////// to replace the cylinder you must put the key in the new one and rotate it so the tip fits into the shaped hole in the column also the steps on the outside of the cylinder must fit into place then you can turn it back and the cylinder will lock itself in when the shiny button has popped into place

the tip you see here above ^ and the steps on the side

now you should understand that's the button you drilled out on top that locks the cylinder in the bottom of the column have fun it won't take to long or be to hard to do but that button will not let go till it is drilled past the hole in the column o.k. so get a nice sharp and greased bit for cooling and rip it up

Sounds like the ignition switch has gone kaput. The ignition switch come in two pieces, an electrical switch and a mechanical switch.

The switch electrical portion can be replaced separatly from the mechanical portion (tumbler that the key engages). It is not a real difficult repair but requires some mechanical knowlege of how the column is assembled.

This can be verified with electrical test equipment prior to buying a new electrical switch.

The ignition switch on Mercury Sable is integrated into the ignition cylinder. When this switch fails, you may need to purchase a special switch from a Ford dealership if the switch used a wireless transponder.


Instructions for NON Functional Cylinder (Cylinder will Not Turn or No Keys ):
1. Disconnect the negative battery cable.
2. Remove the steering wheel.
3. Using locking pliers, twist the cylinder cap until it separates from the lock cylinder.
4. Using a 3/8 in. (10mm) diameter drill bit, drill down the middle of the ignition lock key slot approximately 13/4 in. (44mm) until the lock cylinder releases from its breakaway base. Remove the lock cylinder and drill shavings from the lock cylinder housing.
5. Remove the retainer, washer, ignition switch and actuator. Thoroughly clean all drill shavings and other foreign materials from the casting.
6. Inspect the lock cylinder housing for damage from the removal operation. If the housing is damaged, it must be replaced.

To install:
1. Replace the lock cylinder housing, if damaged.
2. Install the actuator and ignition switch.
3. Install the trim and electrical parts.
4. Install the ignition lock cylinder.
5. Install the steering wheel.
6. Connect the negative battery cable, then check the lock cylinder operation.


Instructions for Functional Cylinder ( Cylinder will Turn with Key):
1. Disconnect the negative battery cable.
2. Turn the lock cylinder key to the RUN position.
3. Using a 1/8 in. (3mm) diameter wire pin or a small drift, depress the lock cylinder retaining pin through the access hole in the upper steering column shroud (under the ignition lock cylinder) while pulling out on the lock cylinder. Remove the lock cylinder from the column.

To install:
1. Install the lock cylinder by turning it to the RUN position and depressing the retaining pin. Insert the lock cylinder into its housing. Make sure the cylinder is fully seated and aligned in the interlocking washer before turning the key to the OFF position. This will permit the cylinder retaining pin to extend into the cylinder housing.
2. Rotate the lock cylinder using the lock cylinder key, to ensure correct mechanical operation in all positions.
3. Connect the negative battery cable.


Door Lock:
When a lock cylinder must be replaced, replace both sides as a set to avoid carrying an extra set of keys.
1. Remove the door trim panel and watershield.
2. Remove the clip attaching the lock cylinder rod to the lock cylinder.
3. Pry the lock cylinder out of the slot in the door.


To install:
1. Work the lock cylinder assembly into the outer door panel.
2. Install the cylinder retainer into the slot and push the retainer onto the lock cylinder.
3. Connect the lock cylinder rod to the lock cylinder and install the clip. Lock and unlock the door to check for proper operation.
4. Install the watershield and door trim panel


Hope this helps.

There is a TSB on this issues if your having ignition lock issues.
Service Information
2009 Chevrolet Cobalt | Cobalt, G5 (VIN A) Service Manual | View All Bulletins | Document ID: 2325129
#09-02-35-005: Ignition Key Difficult to Remove, Ignition Key Binds or Sticks in Cylinder (Replace Ignition Cylinder) - (Aug 10, 2009)

Subject: Ignition Key Difficult to Remove, Ignition Key Binds or Sticks in Cylinder (Replace Ignition Cylinder)

Models: 2008-2009 Cadillac CTS (Built Prior to VIN Breakpoint 90163371)

2005-2009 Chevrolet Cobalt (Built Prior to April 14, 2009)

2006-2009 Chevrolet HHR (Built Prior to April 14, 2009)

2007-2009 Chevrolet Equinox (Built Prior to July 2008)

2005-2006 Pontiac Pursuit (Canada Only)

2006-2009 Pontiac Solstice (Built Prior to April 14, 2009)

2007-2009 Pontiac G5 (Built Prior to April 14, 2009), Torrent (Built Prior to July 2008)

Attention: This bulletin only applies to vehicle equipped with automatic transmission.

the key might be woren or one of the tumblers has broken, might need a new key cyclinder

BMW ignition lock replacing.

According to manual no special tools needed. here procedure!

1. Ignition elec switch. Disconnect battery. 2. remove trimpanel from lower leftside of instrument panel. remove screw retaining lower steering column and remove cove. 3. remove slotted screws on both side of switch. 4. relase tabs and remove switch from elec harnass and remove sealer.. note: before mating new ignition elec switch check that switch is in correct position. seal screws again.
2. Ignition lock cylinder replacing. 1. insert master key and turn 60 deg to radio position. 2. inset piece of stiff wire into opening in lock cylinder and pull cylinder out. (Note early models up to 10/95 turn lock cylinder back 12 deg to release)

for 98 contour issue. TSB 98-21-14 not covered by warranty

This TSB article is being republished in its entirety to include the 1999 Cougar . ISSUE: The ignition key may be difficult to insert or remove and/or key chimes may sound with the ignition key removed and driver's door open on some vehicles. This may be caused by internal design characteristics in the ignition lock cylinder increasing insertion/removal efforts which may allow the lock cylinder to stick.
ACTION: Install a revised ignition lock cylinder. The revised ignition lock cylinder should reduce the possibility of high insertion/removal efforts and ensure proper chime function. Refer to the following Service Procedure for details.
SERVICE PROCEDURE

1. Verify customer concern.
2. Observe the ignition lock cylinder as the key is removed. If the lock cylinder snaps outward to the non-depressed position and the chimes stop sounding, continue to Step 3. If it does not snap outward, replace the ignition lock cylinder with the appropriate cylinder by referring to the Parts Block in this article.
3. Insert and remove the ignition key from the lock cylinder. If binding or high efforts are encountered, replace the ignition lock cylinder.
4. From the Parts Block, select a lock cylinder with a part number suffix identical to the center character of the key code of the vehicle. The suffix must match the center key code character to maintain a single key system.
5. Install the replacement lock cylinder, by referring to the 1998 Contour/Mystique Workshop Manual, Section 211-05 or the 1999 Cougar Workshop Manual, Section 211-04. NOTE: KEYS INCLUDED WITH NEW IGNITION LOCK CYLINDERS ARE CUT FOR THE IGNITION ONLY. IN ORDER FOR THE KEYS TO FUNCTION IN THE DOOR LOCKS, THE KEYS MUST BE CUT TO THE DOOR CODE OF THE ORIGINAL LOCKSET. THE KEY CODE WILL CHANGE UPON INSTALLATION OF THE REPLACEMENT LOCK CYLINDER (FIGURE 1).
   
   
   Figure 1 - Article 98-21-14
   
   NOTE: ADVISE THE CUSTOMER TO DISCARD ALL KEYS THAT WERE CUT TO THE ORIGINAL IGNITION LOCK CYLINDER.
   
6. Record the new key code on the repair order and provide to the customer. Advise the customer to record the new key code in a permanent location and to discard all references to the original key code. NOTE: REPLACEMENT IGNITION LOCK CYLINDERS ARE SHIPPED WITH NON-PASSIVE ANTI-THEFT SYSTEM (PATS) KEYS. IF THE VEHICLE IS EQUIPPED WITH PATS, OBTAIN TWO (2) ROTUNDA KEY BLANKS (OR OTHER FORD AUTHORIZED BLANKS, SUCH AS: ILCO, STRATTEC, CURTIS, HUF, OR VALEO) AND CUT TO THE REVISED KEY CODE. USE OF OTHER UNAUTHORIZED KEYS MAY CAUSE ERRATIC OPERATION OF THE PATS SYSTEM.
   
7. Program PATS keys using one of the two following methods:
   

(1) For vehicles with Integrated PATS (IPATS), function built into the Powertrain Control Module (PCM) and built beginning:

• 2/2/98 Kansas City (Contour/Mystique)
• 2/16/98 Mexico (Contour/Mystique)
• All 1999 Cougars

Using the New Generation Star (NGS) Tester equipped with Service card (green) level 3.0 or higher:

1. From NGS menu, select:
   • Service Bay Functions
   • PCM
   • Enter Security Access (10 minute delay)
   • Ignition Key-Code-Erase
2. Disconnect Data Link Connector (DLC).
3. Cycle the first non-programmed key in the ignition to run position for at least 3 seconds and then turn to the off position.
4. Cycle the second non-programmed key in the ignition to run position. The theft indicator should prove out for 3 seconds.
5. Verify the vehicle will now start using both keys.
   

(2) For Contours/Mystiques with Stand Alone PATS and built before:

• 2/2/98 Kansas City
• 2/16/98 Mexico

Using the New Generation Star (NGS) Tester equipped with Service card (green) level 1.0 or higher:

1. From NGS menu, select:
   • Service Bay Functions
   • PATS
   • Ignition Key-Code-Erase (this process may take up to 8 minutes to complete )
2. Disconnect DLC.
3. Cycle first unprogrammed key in the ignition to run position. First key will program and allow vehicle to start.
4. Again cycle first programmed key to run position. Within 15 seconds, remove original key and turn new unprogrammed key to run position. The theft indicator should prove out for 2 seconds. New key will start vehicle.
5. Repeat this process for additional key programming. NOTE: THE FOLLOWING SHOULD BE NOTED FOR THE PART NUMBER BLOCK:
   • Part Number suffix will match center character in key code
   • Logo on key is Ford for Contour models
   • Logo on key is Mercury for Mystique and Cougar models
   
   

PART NUMBER PART NAME F5RZ-11582-A Ignition Lock Cylinder (Contour) F5RZ-11582-B Ignition Lock Cylinder (Contour) F5RZ-11582-C Ignition Lock Cylinder (Contour) F5RZ-11582-D Ignition Lock Cylinder (Contour) F5RZ-11582-E Ignition Lock Cylinder (Contour) F5RY-11582-A Ignition Lock Cylinder (Mystique, Cougar) F5RY-11582-B Ignition Lock Cylinder (Mystique, Cougar) F5RY-11582-C Ignition Lock Cylinder (Mystique, Cougar) F5RY-11582-D Ignition Lock Cylinder (Mystique, Cougar) F5RY-11582-E Ignition Lock Cylinder (Mystique, Cougar)

this is for 98, but may apply if yours is late 97 build.

Article No.
98-21-14

• IGNITION SWITCH - HIGH EFFORT IGNITION KEY INSERTION/REMOVAL AND/OR KEY CHIMES SOUND WITH DOOR OPEN AND IGNITION KEY REMOVED

Publication Date: OCTOBER 15, 1998
FORD: 1998 CONTOUR LINCOLN-MERCURY: 1998 MYSTIQUE
1999 COUGAR
This TSB article is being republished in its entirety to include the 1999 Cougar . ISSUE: The ignition key may be difficult to insert or remove and/or key chimes may sound with the ignition key removed and driver's door open on some vehicles. This may be caused by internal design characteristics in the ignition lock cylinder increasing insertion/removal efforts which may allow the lock cylinder to stick.
ACTION: Install a revised ignition lock cylinder. The revised ignition lock cylinder should reduce the possibility of high insertion/removal efforts and ensure proper chime function. Refer to the following Service Procedure for details.
SERVICE PROCEDURE

1. Verify customer concern.
2. Observe the ignition lock cylinder as the key is removed. If the lock cylinder snaps outward to the non-depressed position and the chimes stop sounding, continue to Step 3. If it does not snap outward, replace the ignition lock cylinder with the appropriate cylinder by referring to the Parts Block in this article.
3. Insert and remove the ignition key from the lock cylinder. If binding or high efforts are encountered, replace the ignition lock cylinder.
4. From the Parts Block, select a lock cylinder with a part number suffix identical to the center character of the key code of the vehicle. The suffix must match the center key code character to maintain a single key system.
5. Install the replacement lock cylinder, by referring to the 1998 Contour/Mystique Workshop Manual, Section 211-05 or the 1999 Cougar Workshop Manual, Section 211-04. NOTE: KEYS INCLUDED WITH NEW IGNITION LOCK CYLINDERS ARE CUT FOR THE IGNITION ONLY. IN ORDER FOR THE KEYS TO FUNCTION IN THE DOOR LOCKS, THE KEYS MUST BE CUT TO THE DOOR CODE OF THE ORIGINAL LOCKSET. THE KEY CODE WILL CHANGE UPON INSTALLATION OF THE REPLACEMENT LOCK CYLINDER (FIGURE 1).
   
   
   Figure 1 - Article 98-21-14
   
   NOTE: ADVISE THE CUSTOMER TO DISCARD ALL KEYS THAT WERE CUT TO THE ORIGINAL IGNITION LOCK CYLINDER.
   
6. Record the new key code on the repair order and provide to the customer. Advise the customer to record the new key code in a permanent location and to discard all references to the original key code. NOTE: REPLACEMENT IGNITION LOCK CYLINDERS ARE SHIPPED WITH NON-PASSIVE ANTI-THEFT SYSTEM (PATS) KEYS. IF THE VEHICLE IS EQUIPPED WITH PATS, OBTAIN TWO (2) ROTUNDA KEY BLANKS (OR OTHER FORD AUTHORIZED BLANKS, SUCH AS: ILCO, STRATTEC, CURTIS, HUF, OR VALEO) AND CUT TO THE REVISED KEY CODE. USE OF OTHER UNAUTHORIZED KEYS MAY CAUSE ERRATIC OPERATION OF THE PATS SYSTEM.
   
7. Program PATS keys using one of the two following methods:
   

(1) For vehicles with Integrated PATS (IPATS), function built into the Powertrain Control Module (PCM) and built beginning:

• 2/2/98 Kansas City (Contour/Mystique)
• 2/16/98 Mexico (Contour/Mystique)
• All 1999 Cougars

Using the New Generation Star (NGS) Tester equipped with Service card (green) level 3.0 or higher:

1. From NGS menu, select:
   • Service Bay Functions
   • PCM
   • Enter Security Access (10 minute delay)
   • Ignition Key-Code-Erase
2. Disconnect Data Link Connector (DLC).
3. Cycle the first non-programmed key in the ignition to run position for at least 3 seconds and then turn to the off position.
4. Cycle the second non-programmed key in the ignition to run position. The theft indicator should prove out for 3 seconds.
5. Verify the vehicle will now start using both keys.
   

(2) For Contours/Mystiques with Stand Alone PATS and built before:

• 2/2/98 Kansas City
• 2/16/98 Mexico

Using the New Generation Star (NGS) Tester equipped with Service card (green) level 1.0 or higher:

1. From NGS menu, select:
   • Service Bay Functions
   • PATS
   • Ignition Key-Code-Erase (this process may take up to 8 minutes to complete )
2. Disconnect DLC.
3. Cycle first unprogrammed key in the ignition to run position. First key will program and allow vehicle to start.
4. Again cycle first programmed key to run position. Within 15 seconds, remove original key and turn new unprogrammed key to run position. The theft indicator should prove out for 2 seconds. New key will start vehicle.
5. Repeat this process for additional key programming. NOTE: THE FOLLOWING SHOULD BE NOTED FOR THE PART NUMBER BLOCK:
   • Part Number suffix will match center character in key code
   • Logo on key is Ford for Contour models
   • Logo on key is Mercury for Mystique and Cougar models
   
   

PART NUMBER PART NAME F5RZ-11582-A Ignition Lock Cylinder (Contour) F5RZ-11582-B Ignition Lock Cylinder (Contour) F5RZ-11582-C Ignition Lock Cylinder (Contour) F5RZ-11582-D Ignition Lock Cylinder (Contour) F5RZ-11582-E Ignition Lock Cylinder (Contour) F5RY-11582-A Ignition Lock Cylinder (Mystique, Cougar) F5RY-11582-B Ignition Lock Cylinder (Mystique, Cougar) F5RY-11582-C Ignition Lock Cylinder (Mystique, Cougar) F5RY-11582-D Ignition Lock Cylinder (Mystique, Cougar) F5RY-11582-E Ignition Lock Cylinder (Mystique, Cougar