2001 Hyundai - reverse gear is inoperative. The

There are a few steps you can try to get your Hyundai H100 out of reverse gear:

1. Shift the transmission into neutral: Try shifting the transmission into neutral by moving the gearshift lever to the neutral position. If the lever is stuck or difficult to move, you may need to apply more force or use a tool to lever it out of place.
2. Check the linkage: The linkage between the gearshift lever and the transmission can sometimes become disconnected or damaged, causing the transmission to get stuck in one gear. If the linkage is the problem, you may need to have it repaired or replaced.
3. Check the transmission: If the transmission is the problem, you may need to have it serviced or replaced. This is a more serious issue and should be addressed by a mechanic.
4. Check the brake system: If the brake system is not functioning properly, it may be preventing the transmission from coming out of reverse gear. Check the brake fluid level and inspect the brake system for any leaks or other issues.

If you are unable to get your Hyundai H100 out of reverse gear using these steps, it is recommended to have it inspected by a mechanic. They will be able to diagnose the problem and recommend the appropriate repairs.

the brake light switch controls the shift lockout solenoid. perhaps this brake light switch is ajar or misaligned or inoperative. check to see if brake lights are working. there is an override to the shift lever lockout.

5th and reverse gears are on the same selector rail. It is possible that the selector fork has come loose for the 5th gear or reverse. Remove the gear lever turret section of the box and see if the selector rail is moving gears or the rail itself.

Sounds like the shift cable is off the transmission under the hood. Raise the hood and check to see if the cable is moving the linkage going into the transmission when the shift lever is moved in the car. Be sure to have park brake on.

when you put it in reverse,first thing you feel a spring.after tthat you lift,
a security plate,this plate prevent you from going reverse into 1 gear.
cause the axel turn a little further when you allreddy has stop the car.
this takes two sec.thats why when putting it in reverse after you feel the spring you wait two seconds,then puch al the way in reverse.

The linkage may be out of adjustment preventing the shifter from moving into reverse or park.
One way to test this is to disconnect the linkage and manually move the lever on the transmision making sure that it can be set into park. Also try moving the lever counting each click from park to low gear to make sure it is clicking into each gear. If this works then the linkage is probably out of adjustment.
On the link cable there is typically a bolt in an oval shaped metal near the transmission shift lever.
1)Detach the shift cable from the transmission shift lever
2)Put the transmision shift lever in the park position, and also the shifter in the cab
3)Loosen the adjustment bolt
4)Reattach the cable to the lever
5)Tighten the adjustment bolt in place
6)Confirm that you can shift through all of the gears
Hope this helps

There can be play inthe shift levers, play in the connecting links.
One there is play then the levers will not move firmly and so it will not have the postion correct to shift the notches inthe gearr box.
So you may have to see if there is any nylon washers or links that are loose and needs a tightening, if the shift lever shows a wobble then it needs this correction.

The first thing to check is the linkage. Sometimes the linkage will slip, Block the wheels on the car (both front and rear) to prevent rolling. Locate the shift linkage on your transmission, and loosen the nut. You should be able to move the shift lever through all the gears, including "P" and "R". Place the transmission shift lever in "Park" (on the transmission) then move the shift lever (inside the car) in the "P" position and tighten the nut (not a bad idea to use a new locking nut here) You should now be able to shift through all gears. If this does not work, you have a more serious problem that may include a worn or broken belt or broken parking pawl inside the transmission.

Things haven't changed much...look on top of the transmission in the engine compartment and look at the shifting linkage. Look for anything that could be interfering with the shifting. One linkage is the cable to the Shift Lever and Rod that goes down into the transmission. Remove the cable adjustment screw.
Move the shift lever rod towards the front of the Van into the Park Indent Position. Place the Driver's Position (Dash) Shift Lever into Park and then reconnect the Cable to the Shift Lever and tighten down the cable adjustment screw to 70 in-lbs.
Check operation's
Let me know if this helped, or if you have any additional information, questions of problems, Feel free to contact me at FixYa.com!

I have a Dodge Charger 06 model and the gear wont move from Park to reverse. everything else works as far as gas, brake light, etc but my gear wont shift can i get soem help