Need a drawing of how to install a cv boot and axle in a 01 hyundai tiburon step by step fast

It can damage the parts that keep the tires on our car if you don't get the CV axles replaced. You should take your car to a mechanic to replace the axles.

Hello: Your best bet would be to go to Auto Zone or Advance Auto parts store and buy a manual for your HYUNDAI It will give you step by step instructions with illustrations, torque specs etc. The cost of the manual will be less than 25.00.

The RH axle is the long one.

u have to dismantle the drive shaft from the car. maybe u need little knock to the edge of the cv to split the shaft with the cv. then install the drive shaft in reverse order step.

the cv joint on the axle is bad

How to Replace a CV Boot
( DIY Complexity: Hard / Time: 3.2 hours )

Parts:
1. CV Boot
2. CV Boot Clamp Kit

Tools:
1. Mallet Hammer
2. 3/8 in. Drive Ratchet
3. Combination Wrench Set
4. Floor Jack
5. Flashlight
6. Flat Head Screwdriver
7. Socket Set
8. Tire Iron

Steps:
Step 1 Secure the vehicle on a level surface, making sure the vehicle will not roll or lean too much when jacked up.
o Tip: Safety Tip:Always wear safety glasses when working on your vehicle. Wear other personal protective equipment (PPE) when necessary, for example latex gloves or safety shoes.

Step 2 Lift up the front of the vehicle using a jack.
o Tip: Using an aftermarket floor jack, instead of the original equipment (OE) jack, can make the job easier and safer. Verify the condition of the floor jack before use.

Step 3 Secure the vehicle with jack stands on both sides for safety before starting any work. The pinch welds and the frame are the two best locations. Do not rely on the jack to hold the vehicle up while working.
o Tip: Try to find a flat, level, and strong surface to put the jack stands.

Step 4 Find the correct size socket and large ratchet or tire iron and turn the wheel lug nuts counter clockwise. Remove the front wheels.
o Tip: It is a good idea to try and break the lug nuts free before you jack the wheels off the ground. This way they you will not spin the front wheels or put stress on the transaxle.
o Tip: Lug nuts fasten the wheel to the hub and may be on very tight. To gain more leverage, use a breaker bar to loosen the nuts.

Step 5 Inspect the CV boot for damage.
o Tip: The CV joint may be worn if the boot is damaged. Thoroughly inspect the CV joint assembly before installing the new boot. If the CV joint is damaged, replace the entire CV joint axle assembly.

Step 6 Mark the axle for installation reference. Remove the CV joint axle assembly.

Step 7 Using a bench vise, hold the shaft of the CV joint secure so that you can separate the CV joint from the shaft. Remove the CV boot clamps.

Step 8 Slide the CV boot off the outer CV joint.

Step 9 Using a rubber mallet, knock the CV joint off of the axle shaft.

Step 10 Remove the old boot from the CV axle shaft and wipe off any old grease. Clean the sealing surface on the CV joint.

Step 11 Fill the CV joint with grease and get it ready to slide back onto the shaft.

Step 12 Slide the new boot onto the shaft but do not tighten the inner clamp yet. Install a new retaining clip before putting the joint and axle together.

Step 13 Slide the CV joint back onto the axle shaft completely.

Step 14 Pack the boot with grease and slide the boot over the CV joint housing. Secure the boot with new clamps.

Step 15 Install the CV joint and axle back into the vehicle in the reverse order that it was removed.

Step 16 Mount the wheel back onto the hub assembly.

Step 17 Tighten lug nuts in a star pattern and torque to suggested manufacturer specifications in the vehicle owner’s manual.

Step 18 Remove jack stands.

Step 19 Lower vehicle with jack until it is securely on the ground.

Step 20 Drive the vehicle to make sure that any noises are no longer present and that there are no indications of wearing parts. Before road testing, visually inspect the area you have worked on to make sure everything is tightened and assembled properly.

Hope help with this (remember rated and comment this help).

Perhaps the cv joint.

There are no instructions available except with the purchase of SOME boot kits. Depending on the CV joint design, you may not be able to remove the joint from the axle. However, most Hyundai CV joints can be removed from the axle by using a drift and a 2 pound hammer to knock the joint off the axle. Once you've done this, it's a simple matter of removing the old boot and installing the new one w/fresh grease and tension bands. Otherwise, you have to remove the DOJ from the other end of the axle and replace the boot that way.

Sounds like a Constant Velocity (or CV) joint on one of your front axles. If you can lift the car and look underneath, look at the axles coming from each tire and going into the transmission. These will have rubber boots in one or two places. If either of these boots are damaged, it's likely you will have to replace the axle. Hope this helps :)