Rear wheel bearing replacement - 1996 Toyota Avalon

replacing bearing involves removing axle your not replacing a hub but tearing apart axle 99 04 F250 Sterling Rear axle bearing replacement Pt 2 2006 Ford F250 rear hub axle seal replacement F250 Rear Brakes Axle Hub Removal Install 03 07 Powerstroke

Wheel Bearings

Print
Adjustment

2002-05 Models

1. Before servicing the vehicle, refer to the precautions at the beginning of this section.
2. Remove or disconnect the following:
   
   Rear wheel Brake drum Hub cover Cotter pin Lock nut cover
3. Adjust the locknut to achieve wheel bearing play of 0.001-0.006 inches (0.025-0.152 mm).

Removal & Installation

2002-05 Models

1. Before servicing the vehicle, refer to the precautions at the beginning of this section.
2. Remove or disconnect the following:
   
   Rear wheel Brake drum Hub cap Cotter pin Lock nut cover Lock nut Wheel bearing retainer washer and the outer wheel bearing Hub assembly Grease seal Inner wheel bearing
3. Clean and inspect the wheel bearings and races for unusual wear or damage. Replace parts as necessary.

To install:

1. Pack the wheel bearings with grease for assembly.
2. Install or connect the following:
   
   Inner wheel bearing Grease seal Hub assembly Lock nut. Adjust the locknut to achieve wheel bearing play of 0.001-0.006 inches (0.025-0.152 mm). Lock nut cover Cotter pin Hub cap Brake drum Rear wheel
   

Go to YOU TUBE and put in replacing wheel bearing hubs for
nissan altima & watch

There is a lot to see even if on a different vehicle

I doubt you have the tools to do the job

Remove the rear wheel, then the bearing cap. Then remove the split pin out, the crowed washer and bearing nut & washer. Now remove the outer tapered bearing, and the brake disk ...

A Front Wheel Drive Vehicle Can Have Two Types Of Rear Wheel Bearings: Serviceable Bearings, Or Nonserviceable, Sealed Bearings. When Sealed Bearings Fail, The Bolts Holding The Bearing And Hub To The Axel Or Control Arm Must Be Removed. When Installing The New Bearing Assembly, Torque The Bolts To Specifications.Some Manufacturers require The Use Of New Fasteners When Rear Bearings And Hubs Are Replaced.

When A Serviceable Wheel Bearing Is Used, The Bearing Can Be Disassembled And Packed With Grease.It Is Serviced Like A Front Wheel Bearing On A Rear-wheel-Drive-Car.

bearing needs to be replaced.

The rear wheel bearing on a toyota camry is replaced by replacing the wheel bearing and hub as a unit. this is a design change as compare to older models with two piece wheel bearings. Scotch drive wheels. Remove rear wheel. Remove rear brake drum. (note: if emergency brakes are applied you will not be able to remove brake drum) Remove dust cap and hub retaining nut. Hub should slide off as unit. Replace hub with new unit. Installation is reverse of removal.

What year miata?

here is how to replace it on a 2 wheel drive please do not forget to rate and comment about your experience today. 2-Wheel Drive

1. Before servicing the vehicle, refer to the Precautions Section.
   
2. Remove or disconnect the following:
   
   • Negative battery cable
     
   • Rear wheel
     
   • Rear brake drum
     
   • Wheel hub nut
     
   • Wheel hub
     
   • Inner wheel bearing race from the hub
     
   • Snapring
     
   • Wheel bearing outer race from the knuckle
     
3. 
   

To install:

1. Install or connect the following:
   
   • Wheel bearing in to the knuckle
     
   • Snapring
     
   • Wheel hub into the wheel bearing
     
   • Wheel hub nut. Torque the nut to 214 ft. lbs. (290 Nm).
     
   • Brake drum
     
   • Rear wheel
     
   • Negative battery cable
     

REAR WHEEL BEARING/ HUB

Removal Procedure

1. Raise the vehicle. Refer to Vehicle Lifting in General Diagnosis.
2. Remove the wheel and the tire. Refer to Tire and Wheel Removal and Installation in Wheels, Tires and Alignment.
   1. Remove and support the brake caliper. Refer to Brake Caliper Replacement (Front) or Brake Caliper Replacement (Rear) in Brakes.
   2. Remove the brake rotor. Refer to Brake Rotor Replacement in Disc Brakes.
   3. Remove the ABS sensor wire connector.
   4. Remove the four bolts from the control arm.
   5. Remove the hub and bearing from the control arm.
   6. Remove the brake shield from the control arm.
   7. Clean the control arm face and the bore before installing the hub and the bearing.
   Installation Procedure
   
   Notice: Refer to Fastener Notice in Service Precautions.
   
   1. Install the brake shield and the hub and the bearing to the control arm with the four bolts. Be careful not to drop the hub and the bearing, as it could be damaged. Reconnect the ABS sensor. Tighten the hub and bearing bolts to 70 Nm (52 ft. lbs.).
   2. Install the brake rotor. Refer to Brake Rotor Replacement in Disc Brakes.
   3. Install the brake caliper. Refer to Brake Caliper Replacement (Front) or Brake Caliper Replacement (Rear) in Disc Brakes.
   4. Install the wheel and the tire. Refer to Tire and Wheel Removal and Installation in Wheels, Tires and Alignment. Tighten the wheel nuts to 140 Nm (100 ft. lbs.).
   5. Lower the vehicle.