Replacing drivers side low beam headlamp

PAWEL IS A BOT. HE POSTS GENERIC ANSWERS. AND OVERLAYS NAME OF YOUR CAR. 82 GENRIC ANSWERS HIM
AND LIES ABOUT IGN SWITCH.
NOW YOUR CAR.! FACTS, ONLY, 1 CAR
LEARN TO USE THE DMM , CORRECTLY;
HEAD LAMPS ON.(SWITCH) NO KEY IS NEEDED FOR HL.
IS DRIVER LEFT OR RIGHT,? IN USA LEFT.
IS HIGH AND LOW BEAMS DEAD LEFT? No TOLD AT ALL.
PUT METER BLACK LEAD TO THE BATTERY NEG LUG
THEN PROBE RED TO ALL WIRES OF DEAD LAMP 1 BY 1.
12VDC IS GOOD 0 BAD
IF LAMP GROUND PIN READS 12VDC <<< GROUND FAILS.

LEFT LAMP USES GROUND LUG G101. IF R

CAR HAS DRL. SO DRL AND MANUAL LAMPS FAIL
HIGH , LOW , AND FLASH HIGH>? NOT TOLD
DOES ENGINE RUN? OMG NOT TOLD.
THIS CAR RUN HL RELAYS BY BCM CONTROLLER BRAIN


FUSE ARE ON THE OUTPUT OF ALL HL RELAYS
SO IF ALL FUSES INPUT(TOP) ARE DEAD,THAT MEANS
BCM IS FAILING. OR THE SWITCH TO IT.
OR FUSES BLOW TO BCM
WE SCAN THE PCM/BCM TO SE WHY.


HEAD LAMPS ON THE 4 FUSES ALL 4 RIGHT SIDE ARE
12VDC, IF NOT BCM IS MESSED UP, OR RELAY DEAD.
HE LOW BEAM RELAY RUNS BOTH SIDE
SAME WITH BEAM. A RELAY FOR IT.
DRL HOT ONLY IN DRL MODE.
DRL; HAS A SUN SENSOR (AUTO MODE)


BOTTOM HERE IS HEAD LAMPS.SIDE.

HEAD LAMPS ON USA WORK EVEN KEYOFF
SO DOES BCM TO DO THAT, MAIN BATTERY NOT DEAD

Bright lights wont shut off ? Assume you mean high beams ? Reading how they work might thing high beam relay has stuck contacts inside .

Headlamps
The headlamps may be turned ON 2 different ways. First, when the driver places the headlamp switch in the HEADLAMP position, for normal operation. Second, with the headlamp switch placed in the AUTO position, for automatic lamp control (ALC). During ALC, the headlamps will be OFF in daylight conditions, or low beam operation in low light conditions. Battery positive voltage is supplied to the low beam relay and the high beam relay in the underhood fuse block. When low beam headlamps are requested, the body control module (BCM) supplies ground to the coil side of the low beam relay. This activates the relay and the relay supplies voltage to the left hand low beam headlamp through the LH LOW BEAM fuse and to the right hand low beam headlamp through the RH LOW BEAM fuse. Ground for the left hand low beam headlamp is provided at G101. Ground for the right hand low beam headlamp is provided at G102. When high beam headlamps are requested, the body control module (BCM) supplies ground to the coil side of the high beam relay. This activates the relay and the relay supplies voltage to the left hand high beam headlamp through the LH HIGH BEAM fuse and to the right hand high beam headlamp through the RH HIGH BEAM fuse. Ground for the left hand high beam headlamp is provided at G101. Ground for the right hand high beam headlamp is provided at G102.

Did you test the low beam electrical circuit using a volt meter ? Look at a wiring diagram to see what all is involved in turning the lights on ? Do you know how to test electrical circuits ?
Also reading service repair manual about the head lamps opp. would be a good thing to do .
Headlamps
The major common components of this system are the body control module (BCM), ambient light sensor, multifunction switch, park brake switch, and the headlamps.
The headlamps may be turned on in 2 different ways. First, when the driver places the headlamp switch in the HEADLAMP position, normal operation occurs. Second, with the headlamp switch is placed in the AUTO position, automatic lamp control (ALC) occurs. During ALC control, the headlamps will be in daytime running lamp (DRL) operation in daylight conditions, or low beam operation in low light conditions.
The low beam relay and high beam relay receive battery positive voltage directly from the battery through the HDM and COILS fuses in the underhood fuse block. The BCM supplies a ground signal to the low beam relay coil for automatic headlamp control and normal headlamp operation. The BCM also supplies ground to the high beam relay coil for high beam headlamp operation. When the driver places the headlamp switch in the HEADLAMP position and the dimmer switch is in the low beam position, the low beam relay energizes sending current flow through the left and right low beam headlamp fuses to both low beam headlamps. The dimmer switch sends a ground signal to the BCM in the high beam position and a momentary ground signal in the flash-to-Pass (FTP) position from G102 to deactivate the low beam headlights and activate the high beam headlights. With the headlights in the low beam position, the high beams may be momentarily turned on or flashed by activating the FTP portion of the switch.

Low Beams - Standard
The standard low beam headlamps receive voltage from the headlamp driver module located in the underhood fuse block. The body control module (BCM) controls the headlamp driver module with the headlamp low beam relay control circuit. Low beam control is determined by a signal on the headlamp dimmer switch signal circuit from the multifunction switch. When the headlamps are requested ON and the headlamp dimmer switch signal circuit is open, the BCM sends a pulse width modulated (PWM) ground signal though the headlamp low beam relay control circuit to the headlamp driver module which illuminates the low beam headlamps at a 100 percent intensity level. The right and left low beam circuits are independent and are fused separately in the underhood fuse block. The LOW HDLP-RT 10A fuse supplies voltage to the right low beam headlamp and the LOW HDLP-LT 10A fuse supplies voltage to the left low beam headlamp. The right and left headlamps are grounded at G103 and G107 respectively.

Your best bet mite be to have a qualified technician check it

Your best bet , take your vehicle to a qualified repair shop . Before you want to replace the BCM . . Professional tech would check for DTC'S - diagnostic trouble code's in the BCM before replacing part's that are not needed .

No signal at signal wire on relay ???? Which circuit wire mite that be ? Hooking up a factory or professional scan tool to view input data from the switch would also be a good step .

Headlamps
The headlamps may be turned ON 2 different ways. First, when the driver places the headlamp switch in the HEADLAMP position, for normal operation. Second, with the headlamp switch placed in the AUTO position, for automatic lamp control (ALC). During ALC, the headlamps will be OFF in daylight conditions, or low beam operation in low light conditions. Battery positive voltage is supplied to the low beam relay and the high beam relay in the underhood fuse block. When low beam headlamps are requested, the body control module (BCM) supplies ground to the coil side of the low beam relay. This activates the relay and the relay supplies voltage to the left hand low beam headlamp through the LH LOW BEAM fuse and to the right hand low beam headlamp through the RH LOW BEAM fuse. Ground for the left hand low beam headlamp is provided at G101. Ground for the right hand low beam headlamp is provided at G102. When high beam headlamps are requested, the body control module (BCM) supplies ground to the coil side of the high beam relay. This activates the relay and the relay supplies voltage to the left hand high beam headlamp through the LH HIGH BEAM fuse and to the right hand high beam headlamp through the RH HIGH BEAM fuse. Ground for the left hand high beam headlamp is provided at G101. Ground for the right hand high beam headlamp is provided at G102.

Headlamps Inoperative - Low Beams
Step
Action
Yes
No
Schematic Reference: Headlights/Daytime Running Lights (DRL) Schematics
Connector End View Reference: Master Electrical Component List
1
Did you perform the Diagnostic System Check - Vehicle?
YES - Go to Step 2
NO - Go to Diagnostic System Check - Vehicle
2
Place the headlamp switch in the HEADLAMP position.
Place the headlamp dimmer switch in the LOW position.
Do the low beam headlamps illuminate?
YES - Go to Testing for Intermittent Conditions and Poor Connections
NO - Go to Step 3
3
Disconnect the turn/headlamp switch connector C2.
Connect a 15-amp fused jumper between the headlamp low beam signal circuit and a good ground.
Do the low beam headlamps illuminate?
YES - Go to Step 4
NO - Go to Step 5
4
Inspect for poor connections at the harness connector of the turn/headlamp switch. Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs .
Did you find and correct the condition?
YES - Go to Step 7
NO - Go to Step 6
5
Repair an open or high resistance in the headlamp low beam signal circuit. Refer to Circuit Testing and Wiring Repairs .
YES - Did you complete the repair?
NO - Go to Step 7
--
6
Replace the turn/headlamp switch. Refer to Turn Signal Multifunction Switch Replacement .
YES - Did you complete the replacement?
NO - Go to Step 7
--
7
Operate the system in order to verify the repair.
Did you correct the condition?
YES - System OK
No - Go to Step 2

It's more then likely the dimmer switch .

DTC B2575
Circuit Description
The body control module (BCM) turns on the LOW BEAM relay when the ambient light sensor senses a dark condition or the low beam headlamps are requested ON. Battery positive voltage is supplied to the LOW BEAM relay at all times. The BCM grounds the LOW BEAM relay control circuit in order to activate the relay.
DTC Descriptor
This diagnostic procedure supports the following DTC:
DTC B2575 Headlamp Control Circuit

B2575.01
Will set if there is a short to voltage in the low beam relay control circuit.
B2575.06
Will set if there is an open or short to ground in the low beam relay control circuit.

Do you know how to test electrical circuit's using a wiring diagram an a voltmeter ? Reading how the headlamps are suppose to work ,then testing is how to find the problem .
Headlamps
The headlamps may be turned ON 2 different ways. First, when the driver places the headlamp switch in the HEADLAMP position, for normal operation. Second, with the headlamp switch placed in the AUTO position, for automatic lamp control (ALC). During ALC, the headlamps will be OFF in daylight conditions, or low beam operation in low light conditions. Battery positive voltage is supplied to the low beam relay and the high beam relay in the underhood fuse block. When low beam headlamps are requested, the body control module (BCM) supplies ground to the coil side of the low beam relay. This activates the relay and the relay supplies voltage to the left hand low beam headlamp through the LH LOW BEAM fuse and to the right hand low beam headlamp through the RH LOW BEAM fuse. Ground for the left hand low beam headlamp is provided at G101. Ground for the right hand low beam headlamp is provided at G102. When high beam headlamps are requested, the BCM supplies ground to the coil side of the high beam relay. This activates the relay and the relay supplies voltage to the left hand high beam headlamp through the LH HIGH BEAM fuse and to the right hand high beam headlamp through the RH HIGH BEAM fuse. Ground for the left hand high beam headlamp is provided at G101. Ground for the right hand high beam headlamp is provided at G102.

Free wiring diagrams here http://www.bbbind.com/free-tsb Enter vehicle info. Year , make , model an engine . Under system click on lighting , then under subsystem click on headlamps . Click the search button ,then the blue link .

Video's on youtube on electrical testing

Here is how they are suppose to work .
Headlamps
The headlamps may be turned on two different ways. First, when the driver places the headlamp switch in the HEADLAMP position, for normal operation. Second, with the headlamp switch placed in the OFF position, for automatic lamp control (ALC). During ALC, the headlamps will be in day time running lamp (DRL) operation in daylight conditions, or low beam operation in low light conditions. The LH HDLPand RH HDLP fuses, supply battery positive voltage from the underhood junction block to the left and right headlamps. The circuit continues through both low and high beam lamps, then back to the underhood junction block. The low beam and high beam circuits continue to the headlamp switch. The low beam and high beam circuits also provide the body control module (BCM) with both low and high beam inputs. The headlamp switch includes the dimmer switch and the flash-to-pass switch. When the headlamp switch is placed in the HEADLAMP position a path to ground is provided. Ground is provided at G201. Depending on the position of the high/low beam switch, either the low or high beam circuit will now have power and ground.
The LH HDLP fuse in the underhood junction block, supplies battery positive voltage to the automatic lamp control (ALC) headlamp relay coil circuit. The ALC relay switch circuit is connected to the low beam circuit at the headlamp switch. When the headlamp switch is placed in the OFF position, the BCM will automatically turn on the low beams in low light conditions. The BCM energizes the ALC relay, closing the switch contacts and grounding the low beam circuit. Ground is provided at G201. With the headlights in the low beam position, the high beams may be momentarily turned on or flashed with the dimmer switch handle. The flash-to-pass feature is accomplished by pulling the dimmer switch handle toward the driver. The headlights may be switched to high beam with the opposite movement of the dimmer switch lever. When the headlamp dimmer switch handle is pulled toward the driver, the flash-to-pass switch closes grounding the high beam circuit. Ground is provided at G201. Both high beams will remain on until the driver releases the switch handle.
If the driver places the headlight switch in the HEADLAMP position , the headlights will remain on until turned off or the battery runs dead.

Finding a wiring diagram to use along with a DMM - digital multi-meter (voltmeter ) To test the electrical circuits for the headlamps B+ power & ground side of the circuit is the way to find a fix .
Watching a few basic electrical testing video's on youtube may help you .
Basic Electricity for Service Techs Ohm law Current Flow Opens Shorts
How to Use Multimeter to Troubleshoot Common Problems
The Trainer 18 Electrical Testing Tips
Can take years to learn how to trouble shoot automotive electrical systems properly .

On the inside of the lid is a diagram .
The headlamps may be turned ON 2 different ways. First, when the driver places the headlamp switch in the HEADLAMP position, for normal operation. Second, with the headlamp switch placed in the AUTO position, for automatic lamp control (ALC). During ALC, the headlamps will be OFF in daylight conditions, or low beam operation in low light conditions. Battery positive voltage is supplied to the low beam relay and the high beam relay in the underhood fuse block. When low beam headlamps are requested, the body control module (BCM) supplies ground to the coil side of the low beam relay. This activates the relay and the relay supplies voltage to the left hand low beam headlamp through the LH LOW BEAM fuse and to the right hand low beam headlamp through the RH LOW BEAM fuse. Ground for the left hand low beam headlamp is provided at G101. Ground for the right hand low beam headlamp is provided at G102. When high beam headlamps are requested, the body control module (BCM) supplies ground to the coil side of the high beam relay. This activates the relay and the relay supplies voltage to the left hand high beam headlamp through the LH HIGH BEAM fuse and to the right hand high beam headlamp through the RH HIGH BEAM fuse. Ground for the left hand high beam headlamp is provided at G101. Ground for the right hand high beam headlamp is provided at G102.

HEADLAMP (FOR USA)
LT-21
C
D
E
F
G
H
I
J
L
M
A
B
LT
Revision: December 2006
2007 Sentra
8.
CHECK HEADLAMP CIRCUIT
1. Turn ignition switch OFF.
2. Disconnect IPDM E/R connector.
3. Check continuity between IPDM E/R harness connector (A) and
headlamp harness connector (B).
OK or NG
OK >> Replace IPDM E/R. Refer to
PG-30, "
Removal and
Installation of IPDM E/R
"
.
NG >> Repair harness or connector.
Headlamp Low Beam Does Not Illuminate (One Side)
EKS00JMQ
1.
HEADLAMP LOW BEAM FUSE INSPECTION
Inspect 15A fuse [No. 40 (LH) and No. 41 (RH) located in IPDM E/R].
OK or NG
OK >> GO TO 2.
NG >> Repair harness

For Audi A4 the fuse box is located on the left side of dashboard behind a plastic cover (for left hand steering wheel vehicle). On inner face of the plastic cover you will find the fuse diagram.
First fuse on first row from left upper corner is Fuse Nr.20 = F20 (15A) - RH headlamp low beam, headlamp adjustment.
First fuse on second row from left upper corner is Fuse Nr.21 = F21 (15A) - LH headlamp low beam, headlamp adjustment.

high beam or low beam? or both of them on one side.

• One low beam headlamp is inoperative

• Central junction box (CJB) fuse 23 (10A) (RH headlamp).
• CJB fuse 25 (10A) (LH headlamp).
• Circuitry.
• CJB.

• Go To Pinpoint Test C .

• One high beam headlamp is inoperative

• Circuitry.
• Headlamp assembly.

• Go To Pinpoint Test D .

• The high and low beam headlamp is inoperative on one side

• Circuitry.

• REPAIR ground circuit 57 (BK).

• Headlamp switch
• Multifunction switch
• Vehicle Security Module

• Central junction box (CJB) fuse(s):
  • 17 (15A)
  • 23 (10A)
  • 25 (10A)
  • 35 (20A)
  • 40 (20A)
• Circuitry
• Headlamp bulbs
• Daytime running lamp (DRL) relay