Trying to find a part and need a 2001 Caravan parts diagram

Here is you Fuse Box Diagram.

Fuse Box Diagram Dodge Dakota (2001-2004)

https://fuse-box.info > dodge > dodge-dakota-2001-20...
The fuse panel is located behind the cover on the driver's side of the instrument panel. Dodge Dakota (2001-2004). Fuse Box Diagram.


..

Fuse number 1!

Chevrolet Lumina (1995-2001) fuses and relays

https://fuse-box.info > chevrolet > chevrolet-lumina-19...
1998, 1999, 2000, 2001 - Here you will find fuse box diagrams of Chevrolet Lumina 1995, 1996, 1997, 1998, 1999, 2000 and 2001, get information about the ...

Fuse box diagram Chevrolet Lumina 1994-2001

https://fusesdiagram.com > chevrolet > fuse-box-diagra...
Fuse box ?1 diagram 2000-2001 - Instrument panel fuse block is located on passenger's end of instrument panel. fuse box diagram. Assignment of the ...
‎Fuse box ?1 diagram 1994... · ‎Fuse box ?1 diagram 1996...

Chevrolet Lumina (1998 - 2001) - fuse box diagram - Auto ...

https://www.autogenius.info > chevrolet-lumina-1998-2...
Jan 1, 2018 - Chevrolet Lumina (1998 - 2001) - fuse box diagram · Instrument Panel Fuse Block · Underhood Electrical Center - Passenger's Side · Underhood ...

Fuse Box Diagram Toyota Sequoia (2001-2007)

https://fuse-box.info > toyota > toyota-sequoia-2001-20...

2001, 2002 - The fuse box is located in the left side of the instrument panel, behind the cover. The location of the fuses in the passenger compartment: ...

Toyota Sequoia (2001 - 2002) - fuse box diagram - Auto Genius

https://www.autogenius.info > toyota-sequoia-2001-200...

Aug. 21, 2016 - Toyota Sequoia (2001 - 2002) - fuse box diagram · Engine compartment · Instrument panel · Fuses (type A) · Fuses (type B) · Fuses (type C) ...

only need to post once

2001 dodge caravan
Wiring, schematic, electrical diagrams etc are basic contents of these online books they sell here on this website link I have attached. Must check it out

should be on the cover you took off to access the fuses

The 2001 Dodge caravan has 2 heater cores - front (the main one), and the rear. Removal of the
rear heater core is a whole different procedure than the front.

Front Heater Core - Removal and Installation

1. Before servicing the vehicle, refer to the Precautions Section.
2. Align the wheels in the straight-ahead position.
3. Disconnect the negative battery cable.
   CAUTION Before working around the steering wheel or the instrument panel all 2 minutes to pass to allow the air bag module to discharge.
   
4. Drain the cooling system into a clean container for reuse.
5. Remove the steering column, by removing or disconnect the following:
   
   Lower left side steering column cover Parking brake release cable from the parking brake lever 10 steering column cover liner-to-instrument panel bolts and the cover liner
6. Rotate the key to the LOCK position; then, rotate the steering wheel to the LOCKED position.
   
   Gear selector cable and its mounting bracket as an assembly from the upper steering column mounting bracket 2 instrument cluster trim bezel-to-instrument panel screws, retaining clips and bezel 2 steering column shroud-to-steering column screws and the shroud Steering column-to-intermediate steering shaft coupler
   
7. Loosen but do not remove the 2 lower steering column mounting bracket nuts/washers.
   
   2 upper steering column mounting bracket nuts/washers Steering column assembly from the vehicle
   
8. Remove or disconnect the following:
   
   Instrument panel-to-chassis harness interconnect and bracket Lower silencer boot, at the base of the steering shaft
   
9. Working in the engine compartment, pinch off the heater hoses.
   
   Heater core cover. Position some towels under the heater core hoses. Heater core plate and the hoses
   
10. Depress the heater core retaining clips.
11. Lift the accelerator pedal and slide the heater core past it.
12. Depress the brake pedal and remove the heater core from the heater/air conditioning housing assembly.
    
    

    Fig. View of the steering column assembly
    
    
    

    Fig. View of the interconnect and bracket
    
    
    

    Fig. View of the front heater core assembly
    

To install:

1. Depress the brake pedal and install the heater core into the heater/air conditioning housing assembly.
2. Lift the accelerator pedal and slide the heater core past it.
3. Install or connect the following:
   
   Heater hoses (using new O-rings) and the heater core plate Heater core cover Heater hoses clamps, working in the engine compartment Lower silencer boot at the base of the steering shaft Instrument panel-to-chassis harness interconnect and bracket
   
4. Install the steering column assembly by installing or connect the following:
   
   Steering column assembly, carefully into the vehicle. 2 upper and 2 lower steering column mounting bracket nuts/washers. Torque the nuts to 105 inch lbs. (12 Nm). Steering column-to-intermediate steering shaft coupler and tighten the pinch bolt to 21 ft. lbs. (28 Nm) 2 steering column shroud and the shroud-to-steering column screws Bezel, the retaining clips and the 2 instrument cluster trim bezel-to-instrument panel screws Gear selector cable and its mounting bracket as an assembly to the upper steering column mounting bracket 10 steering column cover liner and the cover liner-to-instrument panel bolts Parking brake release cable to the parking brake lever Lower left side steering column cover. Lower left side steering column cover
   
5. Refill the cooling system.
6. Connect the negative battery cable.
7. Run the engine to normal operating temperatures; then, check the climate control operation and check for leaks.

The lights on my instrument panel cluster are going out one at a time, on my 2001 Dodge intrepid, 2 questions?

1. Will replacing whatever relative fuse solve the problem

2. If there's bulbs that needs to be replaced, where are they located? and how do i get to them?
Thanks!!

I call it a dash trim face but there is likely a technical name for it. Just go to the dealer and tell the parts guy what you need and he wont have a problem understanding. Show him the broken one if you need to. Likely you can get one cheaper in a scrap yard.

Instrument Cluster Removal and Installation Disconnect the battery ground cable. For additional information, refer to Section 414-01 . Remove the instrument panel center finish panel. Remove the screws. Disconnect the connectors and remove the instrument panel center finish panel. Remove the hood latch release handle. Remove the screws. Lower the hood latch release handle out of the way. Remove the instrument panel steering column cover. Remove the screws. Remove the instrument panel steering column cover. Remove the instrument panel steering column opening cover reinforcement. Remove the four screws. Remove the instrument panel steering column opening cover reinforcement. Position the column gearshift lever in the low position. Partially remove the instrument cluster finish panel. Remove the screws. Position instrument the cluster finish panel to gain access to electrical connectors. Remove instrument the cluster finish panel. Disconnect the connectors. Remove instrument the cluster finish panel. NOTE: Illustration shows steering column removed for clarity. Remove the instrument cluster. Remove the screws. Remove the transmission range indicator and position the cluster forward to disconnect the three electrical connectors on the back. Remove the instrument cluster.