Engine won't start. Turns over just fine. 12 engine codes P0141,0422,0562,0201,0202,0203,0204,P1553,P1403,P0444 and P0135. P0141 is a repeat.

see
https://www.mycarspecs.com/obd2/isuzu/rodeo/1995/base/p0444-evap-purge-control-valve-circuit-open
not cranking may be a timing belt problem

No code tells you to replace a part , need to do diagnostic's for said code .
P0141 - O2 Heater Circuit (Bank 1, Sensor 2) Description: See the description for DTC P0135. Possible Causes: See the possible causes for DTC P0135. Diagnostic Aids: See the diagnostic aids for DTC P0135. Application Key On Engine Off Key On Engine Running Continuous Memory All GO to Pinpoint Test DW .
DW: Heated Oxygen Sensor (HO2S) DW: Introduction DW1 CHECK FOR DIAGNOSTIC TROUBLE CODES (DTCS) Are DTCs P0040, P0041, P0053, P0054, P0055, P0059, P0060, P0132, P0133, P0135, P0138, P0139, P0141, P0144, P0147, P0152, P0153, P0155, P0158, P0159, P0161, or P1127 present?
Yes No For DTCs P0040 or P0041, GO to DW2 .

For DTCs P0053, P0054, P0055, P0059 or P0060, GO to DW14 .

For DTCs P0132, P0138, P0144, P0152 or P0158, GO to DW20 .

For DTCs P0133 or P0153, GO to DW3 .

For DTCs P0135, P0139, P0141, P0147, P0155, P0159 or P0161, GO to DW9 .

For DTC P1127, GO to DW19 . For all others, GO to Section 4, Diagnostic Trouble Code (DTC) Charts and Descriptions .
DW9 DTCS P0135, P0139, P0141, P0147, P0155, P0159 OR P0161: CHECK FOR A SOURCE OF POTENTIAL HO2S CONTAMINATION

• Investigate the following items as potential sources of HO2S contamination:
  • use of unapproved silicon sealers
  • fuel contaminated by silicon additives
  • excessive oil consumption
  • glycol leaking internally in the engine
  • lead-contaminated fuel
  • short drive cycles in cold weather
  • use of unapproved cleaning agents

Is a concern present?
Yes No REPAIR the source of the contamination.

CHANGE the engine oil and oil filter.

RESET the keep alive memory (KAM). REFER to Section 2, Resetting The Keep Alive Memory (KAM) .

REPEAT the self-test. GO to DW10 .

replace it


P0135 OBD II Trouble Code O2 Sensor Heater Circuit Malfunction Bank 1...

More then likely a blowen seal on head. Take to dealer and have it checked if you catch it befor it go's completely out it shoulden cost as much to fix. But it is going to cost . good luck

How to Diagnose a P0135 -Heater
Performance Bank 1 Sensor 1 (GM 3.5L) January 31, 2012 Updated: October 29, 2014 Written by: Abraham Torres-Arredondo Article Id: 371

• Page 1
• Page 2
• Page 3
• Page 4

If your check engine light is on and you have a diagnostic trouble code P0135 stored in the PCM's memory... then you've come to the right place to test and troubleshoot the upstream oxygen sensor.
A P0135 DTC says: HO2S Heater Performance Bank 1 Sensor 1... and this means that the PCM (Powertrain Control Module = Fuel Injection Computer) has detected a problem with the front oxygen sensor's heater element or a problem in the heater's circuit (wires).
In this tutorial, I'll show you how to check the oxygen (O2) sensor's heater element and the two circuits that feed it with power (10 to 12 Volts) and ground with a multimeter.
In case you're wondering, where the oxygen (O2) sensor that the code P0135 is accusing of being BAD is... this bad boy is located on the exhaust manifold and before the catalytic converter.
To help you navigate this article, here are its main points:

1. Symptoms of a BAD Oxygen Sensor Heater Element.
2. What Tools Do I Need to Test Code P0135?
3. What Does the Heater Inside the Oxygen Sensor Do?
4. Circuit Descriptions of the Downstream Oxygen Sensor.
5. Start Here.
6. TEST 1: Oxygen Sensor Bank 1 Sensor 1 Test.
7. TEST 2: Checking 12 Volts to O2 Heater.
8. TEST 3: Checking the O2 Heater's Ground Circuit.
9. TEST 4: Ohming the O2 Heater Element.
10. P0135 O2 Sensor Heater Test Summary.

Buying a Digital Multimeter for Automotive Diagnostic Testing (found at: easyautodiagnostics.com).

Scan Tool.

1. Don't have one?... check out my recommendation: Abe's Scan Tool Recommendation.

Wire Piercing Probe.

1. Although this tool is not an absolute must, if you do buy one, you'll realize just how easy it makes testing the voltages inside the wires.
2. If you need to see what this tool looks like, you can see it here:Wire Piercing Probe.

< Prev

1

2

3

4

Next >

Applies To:

Buick Vehicles:

• Rainier 4.2L
  • 2004, 2005

Chevrolet Vehicles:

• Colorado 3.5L
  • 2004, 2005
• Trailblazer
  • 2004, 2005

3.5L
How To Test for a Blown Head Gasket (GM 3.5L, 4.2L)
How to Test the MAF Sensor and Codes: P0100, P0101, P0102, P0103
How To Test for a Blown Head Gasket (GM 3.5L -FWD)
All Articles: 3.5L "A day without sunshine is like, you know, night"
Steve Martin
MORE TUTORIALS:

if you can read the faults then teh code reader should tell you ,if not then download OBDII codes from a torrent site as iam feeding .


P1479 Vacuum system, brakes - mechanical fault
P1403 EGR Flow Deviation

3089 is not showing in my VW code sheet

you can google these error code on the internet and usually can find them no problem

The code P0135 is a fault code for the o2 sensor before the catalytic converter.Replace the o2 sensor and then reset the computer and it should be fine afterwards.The check engine light should stay off then.

p1403 is a problem with the DTML sensor ... thats associated with the charcoal canister ... that is often caused by putting too much gas in the tank (overfilling) ... gas gets into the charcoal canister and contaminates it .. you could also have a bad sensor .. there are two .. one on the throttle body the other on the engine .. sometimes the wiring going to these sensors gets corroded or damaged .. contamination in the canister may clear itself in time if you avoid overfilling ..

P0134- O2 sensor Circ, bank 1, Sensor 1 no activity detected

P0135- O2 sensor heater circ, bank 1 sensor 1 malfunction