Hot to install driver's side rearview mirror '98 Expedition

How To Install Replace Side View Mirror Honda CR-V 02-06 ...

? 10:31
https://www.youtube.com/watch?v=tuGFzxCVh7k
May 8, 2012 - Uploaded by 1A Auto Parts
In this video, 1A Auto shows you how to repair, install, fix, change or replace a broken, smashed, cracked, or ...

Replace 2002-2006 Honda CR-V Side Mirror, How to ...

? 14:20
https://www.youtube.com/watch?v=UKLPkZszbrA
Sep 25, 2013 - Uploaded by Go-Parts
Side Mirror purchased from www.Go-Parts.com Links to purchase products: ...

2000 Honda CR-V side mirror replacement - YouTube

no need to remove the door.. just open the screws of the inside concole , opening handle and lever .. take out the console and u will see the screws to open the mirror.

Go to an auto parts store and buy rearview mirror adhesive. Your rearview mirror will separate from the small mounting piece that adheres to the windshield. Clean off the glass where it will sit. Follow the directions on the adhesive package and install the mount on the windshield. Once it dries, install the mirror on the mount. Rearview mirror adhesive is one of the most powerful adhesives on the market. Don't use anything but rearview mirror adhesive or the mirror will not hold.

you either have a loose connection to or a failing daylight sensor, get it replaced

switch is gone replace it

If you need further help, reach me via phone at https://www.6ya.com/expert/scott_541ceb86d69e7743

Spray some WD40 into the latches on the side of the doors then open and close the doors several times firmly.This will unstick the door adjar switch most of the time.Start with drivers door first.

The exterior mirrors:

• are controlled by power controls on the LH front door trim panel.
• are of a foldaway design.
• may contain turn signal indicators.
• may be heated when the heated back window glass is activated.
• may have a programmable recall memory option.

Driver Seat Module
The power driver seat and power exterior mirrors are controlled by the driver seat module (DSM) only when the vehicle is equipped with the programmable/recall memory option.
---------------------------------------------------------------------
Power Exterior Mirror Operation
The power exterior mirrors are controlled by the DSM and are operational all the time, whether the ignition switch is on or off. Using the power exterior mirror switch, the driver can adjust the driver and passenger exterior mirrors four ways.
-----------------------------------------------------
Visual Inspection Chart Mechanical Electrical

• Exterior mirror(s)
• Interior mirror

• Central junction box (CJB) fuse
• Circuitry
• Exterior mirror control switch
• Exterior mirror motor
• Interior mirror
• Driver seat module (DSM)
• Memory set switch

----------------------------------------------------------------------------------

1. If the vehicle is equipped with memory exterior mirrors and the concern remains after the inspection, connect the diagnostic tool to the data link connector (DLC) located beneath the instrument panel. Select the vehicle to be tested from the diagnostic tool menu.
   • Check to make sure the program card is correctly installed.
   • Check the connections to the vehicle.
• Check the ignition switch position.

-------------------------------------------------------------------------------------

• The mirrors are inoperative

• Circuitry.
• Central junction box (CJB) fuse.
• Exterior mirror control switch.

1. Disconnect the negative battery cable.
2. Remove the outside rearview mirror garnish.
3. Disconnect the harness connector.
4. Remove the 3 bolts and the outside mirror.

To install:

1. Install the outside mirror and tighten the bolts to 60 inch lbs. (7 Nm).
2. Connect the wiring harness.
3. Install the mirror garnish.
4. Connect the negative battery cable

Remove the sail panel,the little panel on inside of door at the mirror.
Remove the window regulator switch plate, pry up on the front of it with a small pick or screw driver. Disconnect the electrical connectors.
Remove the top door trim panel screw that is behind the sail panel you removed.
Remove door trim panel screw at window regulator switch plate opening.
Remove door trim panel screw in the courtesy lamp housing. Remove the courtesy lamp lens.Remove the screw.
Remove the inside door handle trim cover.
Remove the bolt.
Remove the inside door handle.
Lift upward to remove the front door trim panel.
Remove the courtesy lamp.
Turn the courtesy lamp bulb socket one quarter turn and remove.
Disconnect the power mirror electrical connector.
Remove the three outside rear view mirror nuts.
Remove the mirror.

I have sent you the instructions to the address you provided. Thanks for choosing FixYa for assistance!