Question about 2002 Jaguar X-Type

1 Answer

Jaguar x type 4 door. how to remove inteior rear panel to replace speaker

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 69 Answers

There are 2 or 3 screws under the panel and other one behind the handle (not the one to open the door, the one you grab to close the door) this one is covered by a round plastic tap, remove it first with a small sharp pointed tool, then very carefully try to pull out the entire panel, be very careful not to broke the clips, you also need to "unplug" the wire that opens and close the locks.

Posted on Oct 04, 2009

Ad

1 Suggested Answer

6ya6ya

6ya staff

  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to replace door lock cylinder drivers side 2002 x-type jaguar.


From inside the door trim. They are $340 new!

Door Trim / Card Removal, Jaguar S-Type R STR - YouTube

? 2:27
https://www.youtube.com/watch?v=PIl_Fsy7BUk
Apr 9, 2015 - Uploaded by Jag TV
This video shows you how to remove your interior door trim / card from a Jaguar S-Type R STR. ... I DONT ...

Drivers Door Handle Help - Jaguar Forums - Jaguar Enthusiasts Forum

https://www.jaguarforums.com > ... > Jaguar Models ( Modern ) > X-Type ( X400 )Jan 23, 2011 - X-Type ( X400 ) - Drivers Door Handle Help - Hi all, im having issues with my drivers door, the quick link posted by JimC64 helped, but the real issue. ... I have a 2002 2.5 sport if that helps. Thanks in ... Disconnect the front door exterior handle connecting rod and the door lock cylinder connecting rod. 4. S-Type 'HOW TO' Guides - Jaguar Forums
23 Sep 2017
How do I remove / replace door lock? X-Type Rear Door?
30 Apr 2011
Drivers door, outside handle removal - Jaguar Forums
27 May 2010
More results from www.jaguarforums.com



replace door lock cylinder drivers side 2002 type jaguar Google Search

Mar 12, 2018 | Cars & Trucks

1 Answer

Replacing quarter glass on left side on 2005 pontiac gto


Remove the door opening weather-strip. Refer to Door Opening Weatherstrip Replacement in Doors.
Remove side sill trim plate. Refer to Door Sill Plate Replacement in Interior Trim.
Remove the lower quarter panel trim. Refer to Rear Quarter Trim Panel Replacement in Interior Trim.
Remove the center pillar upper trim panel. Refer to Center Pillar Upper Trim Panel Replacement in Interior Trim.
Remove the quarter upper trim panel. Refer to Rear Quarter Upper Trim Panel Replacement in Interior Trim.
Remove the center pillar outer applique. Refer to Center Pillar Applique Replacement in Exterior Trim.
Remove the roof drip molding. Refer to Body Side Roof Drip Molding Replacement in Exterior Trim.

Important: It is necessary to use new nuts when reinstalling the quarter window.
Remove the nine quarter window nuts (1), securing the quarter window assembly (2) to the body opening.
Caution: When working with any type of glass or sheet metal with exposed or rough edges, wear approved safety glasses and gloves in order to reduce the chance of personal injury.
Important: When removing the quarter window from the body opening make sure that the attaching pins are clear of the outer body.
Remove the quarter window (2) from the body opening.

Remove the rear seat cushion. Refer to Rear Seat Cushion Replacement in Seats.
Remove the rear seat back. Refer to Rear Seat Back Replacement in Seats.
Remove the door sill plate. Refer to Door Sill Plate Replacement .

Remove the 3 quarter trim panel retaining screws (1).
Starting at the lower edge of the trim panel and moving alternately clockwise and counterclockwise, pull outward on the trim panel to disengage the eight rear quarter trim panel attaching clips (2).
Remove the quarter trim panel from the vehicle.
Remove the 4 radio speaker grille speed clips (1), securing the speaker grille.
Remove the speaker grille (2).
Remove the rear quarter trim panel insulator (1), from the back of the quarter trim assembly (2).
Remove 7 rear quarter trim panel armrest retaining clips (1).
Remove 7 rear quarter trim panel armrest retaining nuts (2).
Gently pry the quarter trim panel armrest insert assembly (3), away from the rear quarter trim panel and remove.

You mite look for a video on youtube !

Dec 23, 2016 | Pontiac Cars & Trucks

2 Answers

Radio volume went out after a popping sound in the rear. It turns on and I can hear it but very faintly.


If power is more than speakers can handle this will happen. If you have a amplifier in the rear than all it is a fuse or a circuit breaker needs to be reset

Mar 25, 2015 | 2007 Jaguar X-Type

1 Answer

Need instructions to replace the passenger side mirror and the driver side tail light on a 1999 Ford Taurus 4-door sedan. Thank you, Gary S.


Section 01-09: Mirrors, Rear View 1999 Taurus/Sable Workshop Manual REMOVAL AND INSTALLATION Procedure revision date: 06/25/1998 Mirror, Power-Outside Rear View Removal
  1. Disconnect battery ground cable (14301).
  1. Remove front door trim panel (23942). Refer to Section 01-05.
  1. Remove radio speaker grille from cover assembly by squeezing or pinching between thumb and index finger.
  1. Remove two screws from cover assembly.
  1. Disconnect outside rearview mirror wiring connector (C515-LH; C615-RH). Remove wiring guides as necessary.
  1. Remove three outside rear view mirror retaining nuts. Remove outside rear view mirror (17682) while guiding wiring and connector through hole in door.


an0786b.gif


Item Part Number Description 1 17682 Outside Rear View Mirror 2 N621906-S36 Nut (3 Req'd) 3 F8DB-17D699-
AAW Cover Assembly Rear Substrate-LH 3 F8DB-17D698-
AAW Cover Assembly Rear Substrate-RH 4 N808968 Screw 5 F8DB-18B984-
AAW Speaker Grille-Standard (No Badge)-LH 5 F8DB-18985-
AAW Speaker Grille-Standard (No Badge)-RH 5 F8DB-18K901-
BAW Speaker Grille-Mach-LH 5 F8DB-18978-
BAW Speaker Grille-Mach-RH 5 F8DB-238A35-
AAW Speaker Grille-Blank (No Speaker)-LH 5 F8DB-238A34-
AAW Speaker Grille-Blank (No Speaker)-RH A - Tighten to 6-8 Nm (54-70 lb-in) ------------------
Trim Panel, Door Front
Removal
  1. Remove cover behind inside door handle.
  1. Remove screw from bottom of pull cup retaining front door trim panel to front door (20124).
  1. Remove three screws retaining front door trim panel to front door.
  1. NOTE: Do not attempt to remove more than one pushpin at a time.

    Using Rotunda Windshield and Molding Trim Removal Kit 107-R0401 or equivalent, remove the door trim panel by pulling one door trim panel pushpin at a time from the inner door skin.
  1. Disconnect electrical connectors as necessary. Refer to Section 01-14A.
Installation
  1. Follow removal procedure in reverse order.
  1. Replace all pushpins with new pushpins (N808994-S).
Front Door Trim Panel


ar0318d.gif

Jan 14, 2011 | 1999 Ford Taurus

1 Answer

How do I replace speakers on a 1994 xj6 ?


Replacement of Front and Rear Door Speakers

Required Tools:

#2 Phillips Screwdriver (magnetic tip is useful)
9 mm Nut Driver
8” or 10” Flat Tip Screwdriver
Small awl or other sharp pointed instrument
Soldering Iron w/solder or 8 to 10 small wire **** splices
8 to 10 small machine screws -- #8 x ¾” or equivalent 8 to 10 small machine screw nuts & flat washers to match
Thread locking compound “Loctite” (optional)
6” wooden dowel of ½” diameter to be used as a drift
Small mallet or hammer

1) Whenever you are attempting to a remove door panel to gain access to the speaker, or any other electrical component, absolutely disconnect the negative battery cable. Battery power is supplied to each door window motor and it’s always prudent to de-energize these circuits before you attempt any panel work.

2) XJ40 door inner panels (front or rear) are comprised of an upper and lower section, which interface to provide complete inner door coverage. Neither panel is difficult to remove nor are any specialized tools required.


3) Remove the Upper Inner Door Panels as follows:

It’s a good idea to store all the removed parts and screws in the adjacent foot well for safekeeping and easy access when you are putting everything back together.

a) Using a small awl (or equivalent), remove the small “square” plastic cover for the inner door lock release mechanism (upper right side when facing inner side of door). It pivots towards the front of the car.

b) Using the #2 Phillips screwdriver, remove the inner door lock release mechanism plastic / chrome escutcheon. It’s held in place by a single machine screw. Pull out on the door lock release mechanism and the escutcheon is easily removed.

c) Using both hands, pull out on the wood veneer panel at the inner door lock release mechanism to provide clearance and slide the panel towards the front of the car. The panel is secured on the left side by slip-in clips and they release easily.

d) Using the #2 Phillips screwdriver, remove the two sheet metal screws on the left side. For the front doors only, lift the bottom of the rubber ventilation boot at the front edge of the door and remove the sheet metal screw. Additionally, for the front door only, use the large flat screwdriver as a lever to ease out the single “fir tree” type press-fit connector. Neither of the rear doors contains these two additional fasteners.

e) Using both hands, lift the upper inner door panel until it releases from the metal ridge along the window line. It doesn’t take much effort to remove the upper panel as it slides off vertically. Store it on the seats for safekeeping.

4) Remove the Lower Inner Door Panels as follows:

a) Using the #2 Phillips screwdriver, remove the sheet metal screw located at the upper edge of the lower panel.

b) Using a ½”small wooden dowel or equivalent drift, place it under the lower edge of the door handle screw access cover. Lightly tap each end of the access cover using the dowel and mallet in an upward direction to release the access cover. These covers can be tight if they have never been removed in the past, but they will release.

c) Using the #2 Phillips screwdriver, remove the sheet metal screw located in the middle of the door handle.

d) Using a small awl or equivalent, remove the bottom door light lens by releasing it from its locator at the rear and sliding it outwards from the door.

e) Using the #2 Phillips screwdriver, remove the lower panel securing sheet metal screw located in the middle of the bottom door light assembly. All sheet metal screw fasteners for the lower panel are now removed.

f) Using both hands (and the large flat screwdriver, if needed), carefully pull off the lower inner door panel by release the series of fir-tree type press-fit connectors along the sides and lower perimeter. Once the panel is removed, it can be laid horizontally on the seat as there is sufficient length of wire bundle to allow this movement. It is not necessary to disconnect the wiring harness, but if desired, the connectors can be released so that the panel can be moved to another more worker friendly location.

5) Remove Door Mounted Speaker as follows:

a) Disconnect the speaker positive and negative conductors by releasing the electrical connector.

b) Using the 9mm Nutdriver, remove the speed clip nut from each of the four (4) speaker fastener studs. Press the nutdriver down firmly to engage the speed nut … do NOT cut away any foam material as it is not necessary.

c) Using the #2 Phillips screwdriver, remove the sheet metal screw immediately to the left (driver side) or right (passenger side) of the speaker as viewed from the back side of the door lower inner panel.

d) Using the #2 Phillips screwdriver, remove the sheet metal screw immediately above the speaker. It is located just below the upper sheet metal screw securing tab on the lower panel … the screw was previously removed in Step 4a.

e) Using the #2 Phillips screwdriver, remove the sheet metal screw immediately to the lower right (driver side) or lower left (passenger side) of the speaker as viewed from the back side of the door lower inner panel.

f) Using the #2 Phillips screwdriver, remove the sheet metal screw immediately to the lower far right (driver side) or lower far left (passenger side) of the speaker as viewed from the back side of the door lower inner panel.

g) Steps 5c, d, e and f will release the speaker / window lift pushbutton panel from the lower door inner panel. Removal of the sheet metal screws will allow the speaker panel to be pulled away from the lower panel by 3” to 4” to facilitate access for speaker removal.

h) With the speaker / window lift pushbutton panel eased back for working clearance, grasp the speaker with one hand while pressing the four (4) speaker studs downward through the foam supporting material. After the studs are clear from the foam material, the speaker can be removed from the panel.

6) Install New Door Mounted Speaker as follows:

Typically, base XJ40 models use 3.5” door speakers while the VDPs will use 4” door speakers. Though I believe it is possible to mount either type in either model.

a) Using the wiring supplied with the new speakers and insulated solderless **** splices, transfer the old speaker wiring electrical connector to the new speaker. Another alternate method is to simply solder the old speaker wires with connector to the new speaker terminals. This is a superior method for electrical continuity and strength of joint … although it does require some soldering skills.

b) Install the new 3.5” speaker by easing back the speaker panel and sliding in the new speaker. Normally, the 3.5” models will mount with only two fasteners.

c) Using two of the small machine screws with flat washers, place these fasteners through the speaker mounting lugs and press them up through the existing holes in the foam supporting material. Secure the screws with flat washers and matching nuts from the back side of the inner door panel. The use of thread locking compound (Loctite) is a nice touch to prevent loosening due to vibration.

d) Re-install the sheet metal screws removed in Steps 5c, d, e and f. This will re-mount the speaker panel. Don’t forget to re-connect the speaker wire connector at the door panel.


7) Re-installation of the inner door lower and upper panels is literally a reverse of the removal procedure. No hidden tricks.

8) Perform Steps 3 through 6 for the other doors and the job is complete.

9) Remove Rear Footwell Mounted Speaker as follows:

This sequence is good for both 4” and 5.25” footwell mounted woofers.

a) Using a small flat screwdriver as a lever, carefully ease off the grill.

b) Using a #2 Phillips screwdriver, remove the four (4) sheet metal mounting screws.

c) Ease out the old speaker and release the electrical connector for the speaker wires.

d) Transfer the old speaker wires and electrical connector to the new speaker using solderless **** splices or by soldering the old leads to the new speaker terminals.

e) Re-connect the speaker wires to the harness by joining the electrical connector.

f) Mount the new speaker and re-attach the necessary sheet metal screws.

g) Press the speaker grill into place.

h) Repeat Steps 9a though 9g for the other footwell speaker.

Mar 10, 2010 | 1994 Jaguar XJ6

2 Answers

How to remove rear door interior door panel


You should obtain a tool made specifically for removing door panels. They are attached by "snap" connectors, and by pulling on the door panel itself will invariably ruin it. Get the tool from a parts place and carefully peer into the slot between the door metal and the door panel. Use the tool slowly with resolution. You should really acquire a manual that guides you for your particular Jag.
Remember, to take the panel completely off, you need to remove the door handle. Look for a plug that has a screw under it. You'll need to pop the door window/lock control panel too, to access screws under there. This can be tricky, so be careful.

Nov 24, 2009 | 2002 Jaguar X-Type

1 Answer

How do i remove the drivers side door panel on a jag s type


This is the same front or rear door. 1. remove rubber insert at the bottom of the arm rest/door handle 2. remove the 2. philip head screws. 3. run hand along bottom edge of door panel to ensure no other securing screws. 4. starting at the top rear edge of the door panel side a large flat screw drive/door panel tool(what ever you have) 5. lift sharply and you will here poping noises fromt the push clips lifting out of the socket. 6. as you work down the rear edge of the door panel you will see the trim around the interior door handle lift away. remove it. 7. the interior door handle will remain on the door. 8. remove the rest of the door panel.

Oct 10, 2009 | 2000 Jaguar S-Type

1 Answer

S Type JAguar Rear Door


First remove all of the screws, some will be hidden under plastic caps, then take a door panel tool (about $5.00 at a parts store) and work it around the panel popping out the plastic keepers. Be carefull and try not to damage the panel where the keepers attach, you can buy new keepers at any auto part store and even Lowe's and Home Depot carry them.

Jul 18, 2009 | 2000 Jaguar S-Type

1 Answer

Remove rear door panel on x type jaguar


You'll need to remove screws that are by the door handle, arm rest, under door and side of door and then gently pull back on the panel as there will also be retaining clips attached and you don't want to break them. If needed, you can pull back the weather seal (can't reuse it, but it's not that important) and you will be able to access everything inside the door

Mar 28, 2009 | 2002 Jaguar X-Type

4 Answers

Jaguar rear window removal


I followed the instructions given by your expert Richard.His instrutions were clear and precise,and I had the problem solved in 5 minutes.best regards A.Taylor

Jul 02, 2008 | 2000 Jaguar S-Type

Not finding what you are looking for?
2002 Jaguar X-Type Logo

564 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jaguar Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22485 Answers

Marvin
Marvin

Level 3 Expert

85222 Answers

Jonah Oneal

Level 3 Expert

14092 Answers

Are you a Jaguar Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...