Remove rear windshield on a 2013 hyundai sonata gls?

SOURCE: replacing rear wheel bearings on 1999 hyundai sonata

1. for drum brakes with sealed hub(all one piece) remove lug nuts and wheel.
2. spray penetrating oil around studs if there is a big phillips head screw visible remove it with impact driver/if not use big ballpeen hammer ,tap on flat of drum near studs(becareful not to hit them) until drum loosens(your creating a shockwave to loosen rust)
3. once drum is off there are 4-bolts coming in from behind backing plate, remove them then hub should be able to be removed w/a little persuation from hammer.

1. remove wheel
2. remove dust cap,cotterpin,star washer(if equipped) do not re use cotter pin
3. remove nut then washer, wiggle brake drum and front bearing will come out.
4. put nut on shaft tighten 2-3 turns grab drum by sides and pull towards you this should remove drum leaving inner bearing/seal on shaft
5. to replace reverse procedure making sure to pack new bearings w/grease(take drum and use long punch to remove bearing races, use race/seal installer to install new races

1. remove wheel
2. remove caliper/bracket
3. remove rotor
4. remove 4-bolts from behind,tap old hub out
5. reverse procedure

SOURCE: How to install a alternator for a 2001 Hyundai Sonata V-6 GLS

Try “autozone.com” or your local library for diagrams and step by step instructions.

SOURCE: How to replace a serpentine belt for a hyundai

try joining autozone.com for free and they have all your diagram needs for free

ZJ Limited

• 17989 Answers
• Posted on Jun 25, 2010

SOURCE: How do I replace the alternator in a 2002 hyundai

For 2002 Hyundai Sonata 2.7L MFI DOHC 6cyl check this procedure...
Alternator - Removal

1. Before servicing the vehicle, refer to the precautions in the beginning of this section.
2. Remove or disconnect the following:
   Negative battery cable Radiator mounting bolts, 1.6L only Alternator drive belt Alternator wiring harness connectors Alternator. It may be necessary to raise the radiator
   
   
   Fig. Exploded view of the alternator-XG 300
   

1. Before servicing the vehicle, refer to the Precautions section.
2. Remove or disconnect the following:
   Negative battery cable Alternator drive belt Alternator wiring harness connectors Alternator. It may be necessary to raise the radiator

1. Before servicing the vehicle, refer to the Precautions section.
2. Remove or disconnect the following:
   Negative battery cable Radiator mounting bolts, 1.6L only Alternator drive belt Alternator wiring harness connectors Alternator. It may be necessary to raise the radiator
   
3. Install or connect the following:
   Alternator and reposition the radiator, if raised Alternator wiring harness connectors Alternator drive belt
4. Adjust the alternator belt and torque the bolts to the following specifications:
   1. Accent: Pivot bolt to 14-18 ft. lbs. (19-25 Nm) and adjustment bolt to 14-20 ft. lbs. (19-28 Nm).
   2. 2.0L and 2.5L Sonata, Elantra and Tiburon: Pivot bolt to 14-18 ft. lbs. (19-25 Nm) and adjustment bolt to 105-132 inch lbs. (12-15 Nm).
   3. 2.4L Sonata: Pivot bolt to 26-41 ft. lbs. (34-54 Nm) and the adjustment bolt to 14-18 ft. lbs. (19-25 Nm).
   4. 3.0L Sonata and XG 300: Pivot bolt to 14-18 ft. lbs. (19-25 Nm) and adjustment bolt to 11-16 ft. lbs. (15-22 Nm).
5. Install the radiator mounting bolts, if removed.
6. Connect the negative battery cable.

Colin Stickland

• 22516 Answers
• Posted on Jan 05, 2011

SOURCE: How do I replace front

the strut has two bolts at the bottom and one on top shouldnr take more than 10mins to dismantle ,unless you mean the suspension and the wheel hub ,even that isnt difficult maybe 20 mins depending on the corrosion state of the bolts

Testimonial: "Very good information."