Question about Kia Cars & Trucks

1 Answer

How to remove of passenger side Bumper cover reflector 2015 Kia Sedona.

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Sergeant:

    An expert that has over 500 points.

  • Expert
  • 354 Answers

Try https://big-manuals.c om , it's very helpful in repairing your vehicle

Posted on Dec 14, 2019

Ad

6 Suggested Answers

6ya6ya

6ya staff

  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad
Fleetw00d

Fleetw00d

  • 31 Answers

SOURCE: Bumper cover removal

It is a little more complicated than that. There are two nuts below the headlight assemblies in the engine compartment. You will need to remove the battery and overflow bottle to get at the one on the passenger side. Remove the turn signals in the bumper, then there are 2 or 3 bolts holding a mounting bracket behind the each of the turn signals. There are a number of bolts with washer heads and reatiners on the underside of the bumper as the previous responder indicated.

Posted on Jan 26, 2009

super_guy

  • 1986 Answers

SOURCE: kia sedona outside door handle replacement

On the inside trim, you can remove screws that are by the door handle, arm rest, under door and side of door and then gently pull back on the panel as there will also be retaining clips attached and you don't want to break them. You'll need to lift the door panel upwards in order to get it off the window ledge. Pull back the weather seal and you'll be able to get to remove the bolts securing the outer handle on

Posted on Sep 15, 2009

MNfisherman

Nate Stansfield

  • 11896 Answers

SOURCE: How to install front bumper cover on 2001 BMW E39

Installation of the Molding
Take the Molding Trim whether it is stock black or painted. Mine is black because my car is a year 2000. Painted side moldings were done in the year 2001. Snap them into place.
dscn5738%20copy.jpg 5 Installation of the Rubber Gaskets
From the stock bumper, retrieve the upper rubber gaskets unless you ordered new ones. Simply take a screw driver and pry a corner off to get you started. Wash thoroughly. NOTE which one belongs on which side.
Place the rubber gasket on the M5 Front Bumper onto its appropriate side. Top dscn5717%20copy.jpg The M5 Bumper is now Fully Assembled!!! Place aside where it can't be damaged.

Posted on Nov 15, 2009

Ronnie Smith

  • 77 Answers

SOURCE: how to remove the rear bumper on a 2005 Kia Sedona

1. Remove rear combination light assembly. A. Remove two mounting screws. B. Disconnect electrical connector from rear side of light assembly. bs6d007a.gif 2. Remove bumper assembly. A. Remove four fasteners and four retaining screws from top of bumper assembly. bs6d007d.gif B. Remove mud flap from bumper assembly. C. Remove two screws from bottom of bumper assembly. bs6d007e.gif D. Remove two screws from side of bumper assembly. bs6d007b.gif E. Remove four bumper mounting bolts from under of vehicle. bs6d007c.gif 3. Install rear bumper in reverse order of removal.

Posted on Jan 30, 2010

Anonymous

  • 179 Answers

SOURCE: how to change the headlight bulb on the passenger

open bonnet remove 10mm bolts securing headlight
pull forward and remove bulb

Posted on Apr 03, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Where is the cooling system bleed valve located 2005 kia sedona


are you referring to the drain plug? if so, it is located on the passenger side bottom facing the front bumper. see attached diagram under radiator removal. http://www.kia-forums.com/attachments/kia-carnival-sedona/9678d1319024147-removing-radiator-kia-sedona-2005-remove-radiator.jpg

Jan 27, 2015 | 2005 Kia Sedona

2 Answers

Where is the cooling system bleed valve located 2005 kia sedona


are you referring to the drain plug? if so, it is located on the passenger side bottom facing the front bumper. see attached diagram under radiator removal.
http://www.kia-forums.com/attachments/kia-carnival-sedona/9678d1319024147-removing-radiator-kia-sedona-2005-remove-radiator.jpg

Jan 27, 2015 | 2005 Kia Sedona

1 Answer

How do i fix dent oncorner of rear bumper on my2012 kia sedona


I would get underneath and look up in the corner to see if you can get a bar between the metal inner bumper and the plastic if you can just pop it out. You may have to pull the bumper off if that doesn't work and pop it out

Dec 07, 2014 | 2012 Kia Sedona LX Passenger Minivan 3.5L...

1 Answer

How to remove bumper


1. Remove rear combination light assembly. A. Remove two mounting screws. B. Disconnect electrical connector from rear side of light assembly.

2. Remove bumper assembly. A. Remove four fasteners and four retaining screws from top of bumper assembly. B. Remove mud flap from bumper assembly. C. Remove two screws from bottom of bumper assembly. D. Remove two screws from side of bumper assembly. E. Remove four bumper mounting bolts from under of vehicle.
3. Install rear bumper in reverse order of removal.

Dec 22, 2013 | 2004 Kia Sedona

1 Answer

Is the a/c plumbing under the engine cover I'n going to charge a/c 2005 kia sedona


It is on the passenger side of the engine compartment, toward the front of the car. In front of the motor mount, down in the fender well.

May 12, 2010 | 2005 Kia Sedona

2 Answers

How do i change the belts on a 2004 kia sedona van


There is a tensioner pulley for each belt, you loosen the nut on the front of the pulley, then there is a tensioner bolt that you loosen, that will move the pulley away from belt to remove the belt. You'll need to get to them from the passenger side under the car. You'll need to remove the plastic covers to get them.

Jan 29, 2010 | 2004 Kia Sedona

1 Answer

How to remove the rear bumper on a 2005 Kia Sedona


1. Remove rear combination light assembly. A. Remove two mounting screws. B. Disconnect electrical connector from rear side of light assembly. bs6d007a.gif 2. Remove bumper assembly. A. Remove four fasteners and four retaining screws from top of bumper assembly. bs6d007d.gif B. Remove mud flap from bumper assembly. C. Remove two screws from bottom of bumper assembly. bs6d007e.gif D. Remove two screws from side of bumper assembly. bs6d007b.gif E. Remove four bumper mounting bolts from under of vehicle. bs6d007c.gif 3. Install rear bumper in reverse order of removal.

Nov 09, 2009 | 2005 Kia Sedona

3 Answers

2005 kia sedona ECU replacement


2005 kia sedona ecu is located on passenger floor under carpet. After you remove the carpet half way, there is a silver plate you have to remove with 10mm deep well socket. there are 4 connector plugs.

Sep 13, 2008 | 2004 Kia Sedona

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

33 people viewed this question

Ask a Question

Usually answered in minutes!

Top Kia Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22485 Answers

Marvin
Marvin

Level 3 Expert

85222 Answers

Jonah Oneal

Level 3 Expert

14092 Answers

Are you a Kia Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...