Question about Ford Cars & Trucks

Open Question

Ford focus ecoboost 1000 turbo front pulley torque settings

Posted by on


6 Suggested Answers


6ya staff

  • 2 Answers


Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017


Colin Stickland

  • 22485 Answers

SOURCE: how to remove a turbo charger from a ford focus tdci

better left to mechanic not easy to do

Posted on Nov 12, 2008



  • 2 Answers

SOURCE: what torque for rear wheel bearing Ford Focus 2000

Can only find out that the hub needs to be tightened to
235 nm Dunno if this helps

Posted on Jan 27, 2009


Chuck Martin

  • 783 Answers

SOURCE: torque settings

Torque Specifications Description Nm lb-ft Brake caliper retaining bolts 28 21 Brake hose to brake caliper union 15 11 Brake caliper anchor plate retaining bolts — 2.0L Duratec ST 133 98

Posted on Mar 15, 2009


  • 277 Answers

SOURCE: torque wrench settings for ford focus thermostat

There is a set spec, but for the DIY mechanic,,
Using a !/4 " drive, with the correct long socket, apply a FIRM effort on the wrench, but obviously not too much, as to sheer the studs. Always use a NEW gasket on all mating surfaces.

Posted on Aug 28, 2009

Testimonial: "a specific torque setting would be better !!"


  • 88 Answers

SOURCE: ford focus wheel nut torque setting for alloy

hi we set them at 100nm which is tight enough and all so tight enough so you can undo them at the side of the road if you need to regards

Posted on Jan 21, 2010

Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

What is the torque specifications ford flex 2009

Your basic 2009 Ford Flex has 248 lb-ft of torque to the wheels. The EcoBoost produces 355 hp (265 kW) and 350 lb-ft of torque. I hope this helps.

Sep 23, 2018 | Ford Cars & Trucks

1 Answer

Focus st 170 mk1 2003 torque setting for both camshaft pulleys worryed in case i have not got it tight enough Thanks John

first time it is 60 psi second time 70 psi and finally third time 80 psi should be ok

Apr 14, 2017 | 2003 Ford Focus

1 Answer

I have Ford Focus 1.0 EcoBoost 2012. I have experienced an intermittent problem where I get a loss of power (turbo not working)and car goes into "limp" mode. No warning light appears and the car

thats sounds like a possible boost control solenoid failure.when the boost solenoid fails it wont activate a warning light and because of the lack of boost the engine computer fail safe feature will put it in limp mode in order to keep the driver from harming the engine

Jul 21, 2016 | 2012 Ford Focus

1 Answer

How reliable is the Ford Focus?

Depends on the year and trim. I like the older single overhead camshaft 2.0l SPI models. They have engine code "P".
Zetec DOHC "3" are powerful, but may drop a valve seat as it ages. I haven't heard much about the 2.3l duratecs, but I suppose that's a good thing. I have heard reports of the new ecoboost motors having trouble, but I bet that's because of people putting regular 87 gas into a turbocharged engine. Turbos need high octane. At anyrate; keep it tuned, change the oil, and keep it under 90. Follow the owner's manual instructions, and you will have no trouble with a Focus or Escort.

Dec 16, 2014 | Ford Focus Cars & Trucks

1 Answer

Camshaft torque settings ford puma 1.4

Crankshaft Belt Pulley 85

Rear crankshaft oil seal carrier 15
Camshaft Timing Belt Pulleys 50

Camshaft timing belt pulleys 50 ft.lbrejakwilson.gif

Same TIGHTENING Sequence for Single OHC


Nov 24, 2010 | 2000 Ford Focus

2 Answers

Serpentine belt diagram for 2002 focus

All information contained here and on subsequent pages are subject to the Terms of Use Policy, which basically states that IS NOT responsible for anything you do to your car... Please read it! :)
Focus Sport Underdrive Crank Pulley Installation This How-To Library article is for the FocusSport crank pulley, which as indicated on the FocusSport product information page, includes a 6061 aluminum lightweight crank underdrive pulley and a new Goodyear Gatorback accessory belt. The FocusSport crank pulley underdrives your accessories by 23%. This, in turn, decreases the drag on the engine, unleashing power that you never knew you had. And since the FocusSport (7.6 ounces) crank underdrive pulley is lighter than OEM (3 lbs. 4 ounces) crank pulley, you'll benefit from the weight reduction of rotating mass; resulting in a more responsive engine. FocusSport crank underdrive pulleys come in a red anodized finish. (Product description taken directly from the FocusSport product page...) Compliments of Forum Member: jaymzr74 Time to Complete: .5 - 1 hour Tools Required:
  • 10mm, 15mm, and 18mm sockets, utility knife, torque wrench, breaker bar or impact wrench(optional).
Instructions: (Click images to Enlarge)
car-raised-small.jpg Note: It helps to have the car on a lift before you begin, though not too high up, as you'll need to get at teh top of the engine bay under the hood. If you don't have access to a lift, use a 2 ton jack stand.
  1. Remove the plastic splash guard inside the right front fender well.
    • There are two 10mm bolts holding it to the fender.
    • After removing the bolts, it should pop right out.

  2. Remove right front wheel.
  3. Remove the bolt on the crank pulley
    • Use an impact wrench if you have access to one.
    • This bolt is a regular right-hand thread.

  4. Install the new pulley on the crank.
    • There is a keyway on the crank that the pulley must fit over.
    • Push it firmly into place by hand first, to avoid binding when you torque it.

  5. Torque the bolt to 85-91 lb-ft.
    • This is tricky if you don't have an impact, so try to find one.

  6. Relieve the belt tensioner and route the new belt over the pulley and accessories.
  7. Reinstall the plastic splash guard.
  8. Put your front wheel back on.

Supporting Belt Diagrams Zetec with A/C
zetec-withac-ad.gif Zetec withOUT A/C

Aug 27, 2010 | Ford Focus Cars & Trucks

1 Answer

How many motor mounts on a 2000 ford focus

1 motor mount right front side, then there's a trans mount left front & torque strut mount. I checked out a nice Poly set (eng & trans) on eBay at about 28.00 includes shipping. Item #170433115996

Jan 30, 2010 | 2000 Ford Focus

1 Answer

Torque settings

Torque Specifications Description Nm lb-ft Brake caliper retaining bolts 28 21 Brake hose to brake caliper union 15 11 Brake caliper anchor plate retaining bolts — 2.0L Duratec ST 133 98

Mar 15, 2009 | 2001 Ford Focus

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

33 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts


Level 3 Expert

85222 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22485 Answers

gerry bissi

Level 3 Expert

4388 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides