Question about Cars & Trucks

1 Answer

2006 w-191,000 Odyssey turns but, no engine run

Got this issue with my vehicle. I have a video on my youtube page for you to watch and see if we can diagnose the issue at hand. Key in turn to start cranks 1 or 2 time goes to the ticking low grinding sound. Similar to a failing battery, dashboard lights dulling and blinking. New Battery installed no change same, turn to start cranks 1 or 2 time goes to the ticking low grinding sound. connected a code reader, which I had no clue on how to use and saw P0335 - crankshaft position A sensor before I cleared the memory. I don't know if the code was there prior, since I had no clue on how to use it.. gun shot to head I have plugged in the code reader several time since cranking the engine to hopefully get another reading, it only says 0 ? yes with the question mark The starter does crank but if you see in the video the belt pulley for the power steering pump just kinda moves back and forth and you hear the grinding and ticking So, what you think.... will not start 3 different videos on youtube , youtu.be/7HQ_npjLHDo , youtu.be/yRHw2p7KBHY , youtu.be/_V4tIaABSLg ,

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Cars & Trucks Master
  • 2,277 Answers

If that's a new battery, and FULLY CHARGED, you probably either have a bad connection from the battery to the starter, or from the battery to engine ground. Possibly a bad starter.
How does it turn over if you try to jump the battery? If no better, check for clean, tight connections, and check the starter (take it off and have it checked at a parts store).

If everything looks good there, and starter checks out OK, check that the engine turns over easily by hand, using the bolt on the harmonic damper. If it is very hard to turn, you may have internal damage - bearings seizing, piston rings dragging, etc.
Another possibility, but doesn't sound like it in the videos, is that there is mechanical interference in the engine (i.e., between pistons and valves).

Posted on Nov 01, 2019

Testimonial: "Thanks for the suggestions."

Ad

6 Suggested Answers

6ya6ya

6ya staff

  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Anonymous

SOURCE: 03 Altima ( 2.5 ) crank position sensor - retired ASE Master Teck

and YOU took much to long to answer --BUT thanks for your attempt -

Posted on Sep 11, 2008

Anonymous

  • 1 Answer

SOURCE: 95 F150 wont crank

the starter should be replaced. The solenoid is kikcing the pinion out but there is no contact being made to turn the starter motor. I have the exact same truck and before i changed the starter used the old starter tap trick. Tap the starter casing with a hammer and it should start turning again. hope this was helpful for you. Good luck.

Posted on Nov 07, 2008

Anonymous

  • 366 Answers

SOURCE: 97 Chevy Astro van lugs, like it misses, B4 finally cranking on

crank shaft sen. is easy enough to change.its mounted near timing chain cover,cam sen.is somewhat harder,its in the distributor,id doubt that both are defect

Posted on Mar 10, 2009

NismoMaster

Walker

  • 146 Answers

SOURCE: Crankshaft Position Sensor Error P0335 recurred after r&r

In the kit there are two sensor that look identical. The one for the crankshaft has a white paint mark on it near the bolt hole. Make sure that it is in the right location.

Posted on Jul 26, 2009

junit80

Jermaine Johnson

  • 81 Answers

SOURCE: 2002 Interpid 2.7 L died on road now no start!

sounds like a bad ecm aka computer to me.have ecm checked

Posted on Aug 15, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Overheat in 2011 chevy cruze lt


My experience has been causes for over heating was.
leak and low coolant, fan not running if you have 2 fans one come on when A/C is turned on the other comes on when engine reaches operating temp. I have had thermostat stuck closed, radiator cap not sealing, fan fuse or relay, temp sensor not working temp sensor could keep your fan from coming on, I have also had to change a couple radiator but it was due to leak. I have heard of some where radiator was blocked up, I think those were issues of stop leak was used for many years.

Video with many causes for engine overheating with solutions
How To Solve An Engine Overheat Condition - EricTheCarGuy
https://www.youtube.com/watch?v=hUzOTnsWImI

Chevrolet Cruze 1.8 LS ECOTEC engine overheat damaged.
Temperature sensor
https://www.youtube.com/watch?v=3s5Rtqss7FU



Sep 23, 2018 | Cars & Trucks

1 Answer

Where's VSS located?


Fixing Ford Taurus Shift Problem. Replacing VSS Vehicle ...

? 7:17
www.youtube.com/watch?v=y0823ZDqxiU
Aug 12, 2010 - Uploaded by Larry W Changing the VSS on a 99 Ford Taurus 3.0L Duratec 24Valve DOHC engine. Symptoms: ... Replacing VSS Vehicle Speed Sensor. Larry W.

98 ford Taurus VSS (vehicle speed sensor) - YouTube

? 1:42
https://www.youtube.com/watch?v=OoPKhl2p6ao
Mar 14, 2015 - Uploaded by Sharon Kay
Location of VSS and how to get to it on a 98 Ford Taurus. Disregard the yr i give in the video. I have 2 other ...

Nov 03, 2015 | 1996 Ford Taurus

1 Answer

Gear stacked on parking ,can not shift gears


2003 Honda Odyssey transmission problems - YouTube

? 1:57
www.youtube.com/watch?v=utHlh9BdPdg
Apr 21, 2013 - Uploaded by PeterGriffin4200 A 2003 Honda Odyssey with an infamously slipping transmissionat only 126k miles. Friend of mine just ...

Sep 12, 2015 | 2003 Honda Odyssey

1 Answer

What is wrong with my honda odyssey the Malfunction indicator lamp is on and the engine is reving up and down in park or netural but idles normal when in gear? The TCS light is also on for no reason.


Check out this video on you tube Check out this video on YouTube: http://www.youtube.com/watch?v=zC6FkziI1ds&feature=youtube_gdata_player

Jul 23, 2011 | 2002 Honda Odyssey

3 Answers

When engine gets hot, idle is up and down with the engine light on. OBD code gives a P0505 code.


per this address "http://www.obd-codes.com/trouble_codes/" p0505 is a "IAC (Idle Air Control) System Malfunction" it gives some good suggestions to look at to find a solution for your problem.

Dec 14, 2010 | 2002 Honda Odyssey

1 Answer

How do i remove the dashboard, to fix a needle for the odometer


i would do a search for "instrument cluster removal honda odyssey" on youtube.com. i doubt you have to pull the whole dashboard and there could be a video of someone removing a cluster. watching someone else do it is worth a million words

Nov 10, 2010 | 2006 Honda Odyssey

1 Answer

2002 honda crv air filter change


Hi!

Can you specify if you are referring to the engine intake air filter or the cabin air filter?
If you are referencing the cabin air filter, the attached youtube video should help.

I originally created the video for the Odyssey, but found out after looking at my dad's CRV that it is essentially the same procedure as the Odyssey, and have also noticed that the same stands true for most Honda vehicles built between 2005 and 2009.

Happy motoring!

Jun 04, 2009 | 2002 Honda CR-V

1 Answer

I have a v40 1.9 turbo diesel - serviced regularly bu main dealer. I have a totally random issue of the engine not starting, it just turns over and does not fire, for most of the time it starts first time...


you may want to look at your Catalytic / O2 sensor(s) Watch this video to learn more about how the O2 sensor works and what is required of the O2 sensor for it to work in the vehicle. https://www.youtube.com/watch?v=DvKZ2GDYEz4 Note: The vehicle in this vehicle does not compare to your own since the sensors on your vehicle may not be under your hood but may be on your header exhaust or you could have one on the lower exhaust pipe and one on the upper exhaust / manifold.

Nov 04, 2017 | Volvo V40 Cars & Trucks

3 Answers

2000 GMC SONOMA SLS


In some applications a check engine light is triggered by the odometer. Requires the dealer to reset. If no ODBII faults are present, the only sensors that are subject to physical wear are the TPS(throttle position sensor) and the 02 sensor(oxygen sensor). These 2 sensors are relatively cheap and should be replaced due to age(2000). To maintain optimum performance, I do 3 things, every 30,000 miles. 1) Change the Air Filter. 2) Replace Fuel Filter and 3) Add a can of B&G44K to a full tank of fuel. The B&G is the best on the market and will condition your fuel pump and injectors. It is available only through dealerships(11.00 a can at Toyota) and should not be substituted. These 3 things are your path to cheap performance and fuel economy

May 22, 2017 | 2000 GMC Sonoma Extended Cab

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

22 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

Marvin
Marvin

Level 3 Expert

85222 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22485 Answers

john h

Level 3 Expert

22486 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...