Question about Hyundai Cars & Trucks

1 Answer

Hi, I have a hyundai sonata hybrid 2013. Scan test shows code " P0A2D" hybrid motor temperature sensor high.

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    New Friend:

    An expert that has 1 follower.

  • Hyundai Expert
  • 171 Answers

Hyundai has a tsb on this code it is 16-at-005 basically it breaks down to this: remove air cleaner find extension motor wire disconnect and measure resistance on pins 2 and 7 which if looking at male pins top row from left over 2 and bottom from left over 2 is pin 7 resistance is 112-142 kila ohms now disconnect trans temp sensor connector measure the resistance on pin 4 top row from left and pin 8 bottom row from left should be same 112-142 kila ohms at outside temp 68 . if reading are not the same resistance replace transaxle,if they both are same resistance replace HPCU (hybrid power control unit ) next step if resistance is different by 1 ohm harness is good,if resistance on both readings are different by more than 1 ohm replace extension wire . may need to send this car to dealership if this testing is more than you can provide yourself,sorry hope it helps

Posted on Nov 03, 2019

Ad

6 Suggested Answers

6ya6ya

6ya staff

  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Pierre Laplante

  • 2042 Answers

SOURCE: Hyundai Sonata 2002 EF-B V6 2.7L

put the bad coil in the place of a good on and check it after that our be sure hope it help fixya our post thanks pierre

Posted on Jul 15, 2008

ghost4548

Paul McGrath

  • 776 Answers

SOURCE: hyundai sonata 01 jerking slow take off high idling

P0715 = Input Shaft Speed Sensor Malfunction
P0765 = P0765 Overdrive solenoid valve problem
The Input shaft speed sensor is located on top of the trans (center) under the shifter cable (the shifter cable is connected to the transaxel range switch). The Overdrive Solenoid valve is located INSIDE the trans (oil pan must be removed to access it).Go to http://www.hmaservice.com/ and register (vehicle by VIN). Afterward, you'll have access to technical information (manuals, wiring diagrams, service bulletins, etc) about your vehicle.

Posted on Jun 25, 2009

ghost45

PAUL MC G

  • 1280 Answers

SOURCE: I have a 2000 hyundai Sonata, 6 cylinder eng. My

The sensor is located on the left hand rear side of the block (near the bell housing). It is held in place by a 10mm bolt. It's to the right of the exhaust manifold (LH - radiator side) on the V6. Once you purchase the new sensor you'll be able to identify it on the engine. The connector to this sensor is located in the illustration.
2cb09a4.jpg A word to the wise... replace the O2 snsr as well.

Posted on Oct 04, 2009

ghost45

PAUL MC G

  • 1280 Answers

SOURCE: 2001 hyundai sonata speed sensor replacement -

Go to www.hmaservice.com and register( Vehicle by VIN). Afterward, you have access to shop manuals, service bulletins, wiring diagrams, etc. about your vehicle.

Posted on Oct 18, 2009

SOURCE: PO301 code on Hyundai Sonata. Replaced wires,

P0301 - Cylinder 1 Misfire Detected.


Possible Causes:
- Improper spark plug at cylinder #1
- Insufficient compression at cylinder #1
- Incorrect fuel pressure
- The injector circuit is open or shorted at cylinder #1
- Fuel injector #1 may be faulty
- Intake air leak at cylinder


Possible Solutions:
- Perform Injector Service
- Replaced Spark Plug #1
- Replaced Injector #1
- Replaced Ignition Coil #1

Posted on Jan 17, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

Tip

How to fix the outside temperature gauge


A common problem on Hyundai vehicles is the outside temperature reading in their dash stopped working or displays incorrect temperature. The models in question with this fault are the 2011 Santa Fe, 2013 Sonata, 2013 Elantra.
The problem lies in the wiring harness along the bottom of the rad saddle (bottom/center of rad ). The ambient sensor is located near the horn in front of the rad. Examine the ambient sensor for damage and them follow the two wire down to the bottom of the rad, open up the harness and you will fine a break in the sensor wire from corrosion/ moisture. Repair/ solder in new piece of wire and heat shrink.

on Feb 23, 2015 | 2011 Hyundai Santa Fe

1 Answer

Hyundai Sonata Hybrid 2011 Vehicle Indicator Light on ... what does it mean?? Hyundai Service could not answer my question and wait until Ninday got the Tech


There are a few things that could be wrong, best thing to do is, wait until they check your vehicle and go from there. If you have a scan tool, posting the codes you find would help us to assist you.

Dec 23, 2016 | 2011 Hyundai Sonata

1 Answer

2006 Hyundai Sonata V 6 location coolant sensor location


Here's the location of the engine coolant temperature sensor, it is Usually On or very near the thermostat housing. http://ww2.justanswer.com/uploads/AM/amdhcds/2013-01-27_010915_ect.jpg

Aug 05, 2015 | Hyundai Cars & Trucks

2 Answers

It's cold outside and my 2013 Hyundai sonata won't start


Its most likely a worn down battery. They get even weaker when its very cold outside. I'd get a jump or connect a charger to it.

Feb 20, 2015 | 2013 Hyundai Sonata GLS

1 Answer

2004 Hyundai sonata eng code PL121, a throttle position sensor, but the throttle position sensor tests out good. What else could it be?


Code 121 is for a problem with the circuit for the sensor.
The computer is getting a signal that is out of range, too low or too high.
If you know for a fact the sensor is ok, you may have to check the circuit back to the computer. You would also need a scanner to read the sensor signal.

Jan 18, 2013 | Hyundai Motor 2004 Sonata

1 Answer

What is a P0105 check engine code on a 2004 Hyundai Sonata?


The code is telling you there is a problem with the MAP sensor which measures vacuum in the intake and outside air pressure.
The sensor needs to be tested and possibly replaced.

Sep 03, 2012 | Hyundai Motor 2004 Sonata

1 Answer

Where is the engine coolant temp. circuit high input located on a 2001 hyundai sonata...code p0441


Trouble code P0441 indicates EVAP emiddion control system incorrect purge flow.
Possible faulty purge valve or circuit.
Possible causes: purge line plugged, vacuum hose failure, EVAP purge solenoid failure and/or emission canister clogged.

The coolant sensor is a 2 wire sensor located in the thermostat housing.

Oct 04, 2011 | Hyundai Motor 2002 Sonata

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

25 people viewed this question

Ask a Question

Usually answered in minutes!

Top Hyundai Experts

Marvin
Marvin

Level 3 Expert

85223 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22485 Answers

Jonah Oneal

Level 3 Expert

14092 Answers

Are you a Hyundai Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...