Question about Jaguar Cars & Trucks

Open Question

How to remove the rear plastic bumper cover on a 2009 Jaguar XJ VP

Posted by on

Ad

6 Suggested Answers

6ya6ya

6ya staff

  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Anonymous

  • 99 Answers

SOURCE: Remove rear plastic bumper cover

please email me at meanness628@aim.com with any other info or questions if you have already gone to a body shop

Posted on Sep 29, 2008

Ad
tunde007

Tunde Autos

  • 2382 Answers

SOURCE: how to remove rear bumper plastic cover toyoto

Hi, to remove the bumper on your Toyota Camry 2006, follow this instructiion...
Remove the row of five bolts from the front edge of the rear bumper, just behind the rear tires, with a Phillips screwdriver.

Reach inside the rear bumper where the bumper meets with the rear quarter panel of the car, just behind the rear tire. Remove the row of bolts with a ratchet and 10mm socket.

Open the trunk and find the row of plastic clips along the top of the bumpre on the outside of the trunk. These clips look like plastic circles. Pry them up with a flat screwdriver until they pop out. Pull the bumper off of the Camry.

Posted on Jan 31, 2011

Medicfox1459

  • 6 Answers

SOURCE: how to remove the front bumper cover on 2002

Remove all eight small set screws (4) on each side in the fender wheel wells. Then remove the four secure bolts on undercarriage of bumper (4). Take a screw driver. (flathead) to the upper portions of both the left and right side of the bumper. Be careful....... These are extremely fragile and you may need to replace them before replacing the bumper. Then comes a bit unnerving part. Removal of the bumper........ (This scarred the **** out of me!!!!) just grab ahold of one of the corners, then gradually pull! That's it. The clips will come out gradually and evenly.

Posted on Feb 20, 2011

dannijnr

  • 1 Answer

SOURCE: S Type Jaguar rear bumper removal

how do you remove a front bumper off of an jaguar s type?

Posted on Mar 15, 2011

ginko

Ginko

  • 19396 Answers

SOURCE: Step by step instructions for

Hi.

Here you go:

1 - Remove one screw at each side's fender:

ginko_114.gif

2 Remove two screws and clips at the back.

ginko_115.gif
3 Pull out the bumper.

4 If needed remove screws holding spoiler support

ginko_116.gif
ginko_117.gif

5 Perform operations in reverse order to reassemble

Posted on Apr 16, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

How to take rear bumper cover off ford flex


THE BUMPER COVER IS ATTACHED TO THE BODY WITH A LARGE NUMBER OF "LEGO" STYLE CONNECTIONS THAT CAN BE PULLED APART WITH FORCE ONCE ALL THE VISIBLE FASTENERS ARE REMOVED

Apr 09, 2015 | 2009 Ford Flex

1 Answer

Where is the fuel filter located on a Jaguar xj8 2003?


if it is the older xj its at the lh rear over the top of the drive shaft area, if its the later all alluminium xj350 module i think it is under the lh plastic cover that runs down the lh underside towards the front of car, hope this helps.

Feb 14, 2015 | 2003 Jaguar XJ-Series

1 Answer

How to remove back bumper on 2000 jaguar xj8


remove rear mudflaps if fitted, remove screws from rear of wheel arch liners. two 19mm headed bolts from underside of bumper, be warned they sieze and a lot of force will destroy the bumper mounts and the bumper beam not cheap to repair.

Oct 31, 2013 | Jaguar XJ8 Cars & Trucks

1 Answer

Removing jaguar s type rear bumper..


disconnect the connector from the park aid module push the connector and grommet out of the back panel remove screws from lower rear of wheel arch liners remove boot floor trim remove plastic boot closing panel trim remove both boot side trims you wil find a number of 10mm headed bolts around the boot at the sides and back remove these and get someone to help you remove the bumper liner the 2 outer sensors can normally be changed without removing the bumper liner on some models

Mar 26, 2013 | 2003 Jaguar S-Type

2 Answers

How do I remove the back bumper from a 2006 hyundai tuscon?


take help of the following steps to remove rear bumper on ur tucson.

Open the trunk of your vehicle.
  1. Unscrew all the screws on the inside plastic trim that covers your bumper to trunk connection.
  2. Pry the plastic piece out with a flathead screwdriver. You will expose the bolts that attach the rear bumper to the trunk.
  3. Unscrew the bolts connecting to the inside of your rear bumper. There should be four bolts.
  4. Unscrew the two to four screws connecting to your bumper from the inside of the rear wheel tire wells. These screws are on the area of the tire well that is closet to the bumper.
  5. Slide under the rear of your car. Use a flathead screwdriver to pop the plastic rivets out of place along the underside of the rear bumper. There should be four to six rivets.

  6. Squat behind your car and firmly pull the bumper off. There will popping plastic sounds, this is the pop-in-place plastic rivets that are the last pieces that hold your rear bumper in place.

Dec 27, 2010 | 2005 Hyundai Tucson

1 Answer

How to replace the rear bumper cover on a Chrysler Pacifica


1. Open liftgate. 2. Remove both taillight assemblies by removing 2 hex-head bolts located in the area revealed when the liftgate is opened. 3. Remove 4 plastic retainers on the very bottom of the bumper cover in the rear. 4. Remove 2 phillips head screws in the wheel well rear lip. 5. Remove 4 pop-up plastic retainers in liftgate area. Use two screw drivers to lift the head and then pull the entire retainer out. 6. Remove a hex-head bolt from each side in the area revealed when the taillight assembly was removed. 7. Bend the bumper cover outward on each side to clear the wheel well lip and remove the bumper. Have a blanket or carpet on the ground to protect the bumper. 8. Remove metal clips from tabs that connect the upper bumper cover to the lower bumper cover. 9. Drill out pop-rivets that connect upper bumper cover to lower bumper cover. 10. Push tabs out of slots to separate the upper and lower bumper covers. 11. Release tab locks on chrome trim pieces and remove from upper bumper cover. 12. Reverse this process to replace the bumper cover.

Feb 16, 2010 | 2006 Chrysler Pacifica

1 Answer

How do you replace rear bumper cover on 2009 Honda Civic


Should look for the bumper shocks and remove which ever is easiest, remove bumper then remove cover , replace cover and reinstall bumper, watch out for wires and clips might hold cover to side plastic.

May 24, 2017 | 2009 Honda Civic

1 Answer

Need to remove rear bumper cover from a 2009 Toyota Corolla


paint it on the car or simply remove all the bolts and screws.  Duh

Mar 15, 2009 | 2009 Toyota Corolla

1 Answer

S Type Jaguar rear bumper removal


how do you remove a front bumper off of an jaguar s type?

Mar 09, 2009 | 2004 Jaguar S Type

1 Answer

Remove rear plastic bumper cover


please email me at meanness628@aim.com with any other info or questions if you have already gone to a body shop

Jun 24, 2008 | 2002 Toyota Camry

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

27 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jaguar Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22485 Answers

Marvin
Marvin

Level 3 Expert

85222 Answers

Jonah Oneal

Level 3 Expert

14092 Answers

Are you a Jaguar Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...