The battery die and after i recharge the battery the remotes are not working can someone help me how to program a keyless entry for land rover discovery 2004?
MOST OF THE TIME WHEN YOU HAVE PROBLEMS IN THE REMOTE AND KEYLESS ENTRY.THE DEALERSHIP HAS TO REPROGRAM IT.BUT FIRST CHECK ALL THE FUSES AND RELAYS.IF THEY ARE OKAY.THEN DEALERSHIP HAS TO FIX.
- If you need clarification, ask it in the comment box above.
- Better answers use proper spelling and grammar.
- Provide details, support with references or personal experience.
Tell us some more! Your answer needs to include more details to help people.You can't post answers that contain an email address.Please enter a valid email address.The email address entered is already associated to an account.Login to postPlease use English characters only.
Tip: The max point reward for answering a question is 15.
You did it like this ?
Programming -Keyless Entry Remote Transmitter
NOTE: All keyless entry remote transmitters (15K601) must be programmed at the same time. NOTE: All previous transmitter identification codes (TIC's) will be erased when programming mode is entered. NOTE: To program (or reprogram) the keyless entry remote transmitters into the generic electronic module (GEM)(14B204), perform the following steps.
Turn the ignition from OFF to RUN eight times within 10 seconds, ending in RUN. If the GEM has successfully entered program mode, it will lock and unlock all the doors.
NOTE: The first TIC must be entered within 7.5 seconds of entering the program mode and additional TICs must be entered within 7.5 seconds of the first TIC. The programming mode is exited whenever the timing constraints are not met. Press any button on a keyless entry remote transmitter, and the doors will lock and then unlock to confirm that each keyless entry remote transmitter has been programmed.
If the door locks do not respond for any keyless entry remote transmitter, wait for several seconds and press the button again.
Turn the ignition switch to the OFF position, or wait up to five minutes after step 1, to exit program mode. If a keyless entry remote transmitter has been programmed (or reprogrammed), the GEM will lock and unlock all the doors one last time.
So the car does not start after getting a new key cut correct? If you have the title to the vehicle, take it to your local Land Rover dealer and they can cut you a new key. Does the car have keyless entry/anti theft from the factory? If so they key will need programmed by the dealer.
Try reprogramming the remotes. Here are the instructions for the procedure. Hope it helps. Cobra!
Programming
NOTE: All keyless entry remote transmitters (15K601) must be
programmed at the same time. NOTE: To program (or reprogram) the keyless entry remote transmitters
into the RAP module, perform the following steps:
Make sure that the anti-theft system is not armed or triggered.
Turn the ignition switch (11572) from OFF to RUN eight times within ten
seconds, ending in RUN. If the RAP module has successfully entered program mode,
it will lock and then unlock all doors.
Within 20 seconds, press any button on a keyless entry remote transmitter,
and the doors will lock and then unlock to confirm that each keyless entry
remote transmitter has been programmed. Repeat this step for each
transmitter.
If the door locks do not respond for any keyless entry remote transmitter,
wait several seconds and press the button again. If the door locks still fail to
respond, refer to Inspection and Verification.
Turn the ignition switch to the OFF position, or wait up to 20 seconds after
step 2, to exit program mode. If a keyless entry remote transmitter has been
programmed (or reprogrammed), the RAP module will lock and unlock all doors one
last time to confirm.
Sorry but Land Rover is one of those car companies that make their car so it can only be worked on by one of their mechanic's. Except for changing the battery inside the remote you are going to send it to them.
You don't normally program a keyless entry, that's done for you by the technicians that install that. If the replaced battery doesn't solve the problem, take the battery and the remote to the techies that installed it.
does trunk button work? panic button?
here's 2003 info:
The doors do not lock/unlock using the remote transmitter
Remote transmitter.
Driver door module (DDM).
Go To Pinpoint Test G .
SECTION 501-14: Handles, Locks, Latches and Entry Systems
2003 Town Car Workshop Manual
GENERAL PROCEDURES
Remote Transmitter Programming
Cycle the ignition from OFF to RUN four times within three seconds. The locks will then lock and unlock, confirming that the program mode has been entered.
NOTE: When the first keyless entry remote transmitter is programmed, all other keyless entry remote transmitters are erased. Press any button on the transmitter to be programmed.
If additional keyless entry remote transmitters are to be programmed, repeat Step 2 within 7.5 seconds.
To exit program mode, turn the ignition to START or wait 7.5 seconds.
--------------------------------------------------------------
report back
×