At Fixya.com, our trusted experts are meticulously vetted and possess extensive experience in their respective fields. Backed by a community of knowledgeable professionals, our platform ensures that the solutions provided are thoroughly researched and validated.
I have a 92 model Lucida 4X4 Automatic diesel. After i start the vehicle and apply gear to drive mode, the engine was stopping.Couldn't understand where the problem lies?
- If you need clarification, ask it in the comment box above.
- Better answers use proper spelling and grammar.
- Provide details, support with references or personal experience.
Tell us some more! Your answer needs to include more details to help people.You can't post answers that contain an email address.Please enter a valid email address.The email address entered is already associated to an account.Login to postPlease use English characters only.
Tip: The max point reward for answering a question is 15.
If the engines are the same year, drive train (Auto or Stick), CC, and came out of the same make/model of vehicle you can usually do the swap. However, It will be an 'Engine Only' swap.
The main difference between the 4x4 and the 4x2 is the transmission layout. The 4x4 has an extra section of gearing on the drive system called a 'Transfer Case'. This is where the split to front and rear drive comes from.
If you remove the engines from the transmission housing like you were changing a clutch you should be able to take one engine out and drop the other one straight in.
On some set ups you can leave the transmission in place and unbolt at the engine end of the Transfer Case but to be honest removing just the engine is easier as you don't have to wrestle with a bigger, longer and heavier lump when the transmission is still fitted.
the rpm limiter will pull back the rpm to limp mode
select low range 1st gear or if automatic select manual 1st gear That will allow higher rpm at low speed
At best as I know the 2005 Prado is all time 4WD vehicle.
Is the engine running ? Can you shift the gears ?
May be something is broken in the drive train...
As a suggestion you can go home by locking the centre differential, proceeding at low speed and checking for noises .
Pls. let me know if it helps...
Which of these does your vehicle have ?
The NVG 233 transfer case features a 3 button shift control switch, located on the instrument panel.
The NVG 236 transfer case features a 4 button shift control switch located on the instrument panel.
Do you know what DTC'S - diagnostic trouble codes are ? Both of these 4X4 systems can set DTC'S , Having a professional or factory scanner is what is needed to check for these codes . Not a OBD 2 code reader or autozone , advance etc... The four button system can set a bunch of them .
DTC B2725
DTC C0300
DTC C0305
DTC C0308
DTC C0309
DTC C0310
DTC C0315
DTC C0323
DTC C0324
DTC C0327
DTC C0362
DTC C0367
DTC C0374
DTC C0376
DTC C0387
DTC C0550
DTC C0611
The NVG 233 transfer case features a 3 button shift control switch, located on the instrument panel. When the ignition is in the RUN position, the transfer case shift control module starts monitoring the transfer case shift control switch, to determine if a new mode/gear position has been selected. At a single press of the transfer case shift control switch, the lamp of the new position begins flashing to inform the driver that the transfer case shift control module has received the request for a new mode/gear position. The lamp continues to flash until all shifting criteria has been met and the new mode/gear position has been reached, or has engaged. Once the new mode/gear position is fully active, the switch indicator lamp for the new position remains ON constantly.
The NVG 233 transfer case provides the driver with 3 manual mode/gear positions:
• 2HI - 2 Wheel Drive high range
• 4HI - 4 Wheel Drive high range
• 4LO - 4 Wheel Drive low range
Any of these mode/gear positions may be selected while driving the vehicle. However, the transfer case will not allow a shift into, or out of, 4LO unless the following criteria has been met:
• The engine is running.
• The automatic transmission is in Neutral, or the clutch pedal is applied on manual transmissions.
• The vehicle speed is below 5 km/h (3 mph).
Finding out what if any codes are stored should be your first step .
This sounds like a problem with the torque converter lockup system. Usually the torque converter lockup solenoid is at fault in your condition. This solenoid usually locks up the torque convertor (which acts like a clutch in an automatic transmission) when you are driving at a certain speed, and unlocks it when you press the brake, and/or come to a stop. When a torque converter stays locked up, and you stop the vehicle, it acts like a vehicle with a manual transmission, if you bring the vehicle to a complete stop without applying the clutch pedal, the brakes stall the engine. Basically, if the torque converter can't unlock, even when you come to a stop, the engine is still locked to the transmission, and even when you apply the brakes, the torque converter doesn't slip and freewheel like it should, but instead stalls the engine.
Try this relearn procedure hopefully it will help Vehicles equipped with engine or transmission computers may require a relearn procedure after the vehicle battery is disconnected. Many vehicle computers memorize and store vehicle operation patterns for optimum driveability and performance. When the vehicle battery is disconnected, this memory is lost. The computer will use default data until new data from each key start is stored. As the computer memorizes vehicle operation for each new key start, driveability is restored. Vehicle computers may memorize vehicles operation patterns for 40 or more key starts. Customers often complain of driveability problems during the relearn stage because the vehicle acts differently then before being serviced. Depending on the type of vehicle and how it is equipped, the following complaints (driveability problems) may exist:
Harsh Or Poor Shift Quality Rough Or Unstable Idle Hesitation Or Stumble Rich Or Lean Running Poor Fuel Mileage
These symptoms and complaints should disappear after a number of drive cycles have been memorized. To reduce the possibility of complaints, after any service which requires battery power to be disconnected, vehicle should be road tested.
Vehicle Preparation
Ensure all components are connected. Ensure transmission fluid level is correct. Warm engine to normal operating temperature. If vehicle has been repaired, perform KOEO and Continuous Memory Code Self-Test and ensure fault codes are not present.
Computer Relearn Procedures
Idle Relearn Procedure
Place automatic transmission in Park or manual transmission in Neutral position. Ensure the emergency brake has been set and all accessories are turned off. Start engine and bring to normal operating temperature. Allow manual transmission vehicle to idle in Neutral for one minute. Allow automatic transmission to idle in Neutral for one minute and then to idle in Drive for one minute. Once initial relearn is complete, process will be completed during normal driving. Always complete the procedure before returning the vehicle to the customer.
Drive Cycle Test (AOD-E, AXOD & AXOD-E TRANSAXLES)
With transmission gear selector in Overdrive, moderately accelerate vehicle to 50 MPH for a minimum of 15 seconds. Transmission should be in 4th gear. While holding speed steady, lightly apply and release brake for about 5 seconds. Stop and park vehicle for a minimum of 20 seconds with transmission gear selector in Drive. Repeat procedure 5 times. Always complete the procedure before returning the vehicle to the customer.
Drive Cycle Test (E4OD)
With transmission gear selector in Drive, press Overdrive Cancel Switch (LED should light). Moderately accelerate vehicle to 40 MPH for a minimum of 15 seconds (30 seconds above 4000-ft. elevation) Transmission should be in 3rd gear. While holding speed steady, press Overdrive Cancel Switch (LED should go off) and accelerate from 40 MPH to 50 MPH. Transmission should shift from 3rd gear to 4th gear. Hold speed steady for 15 seconds. While holding speed steady, lightly apply and release brakes enough to turn brake lights on. Maintain 50 MPH for about 5 seconds. Stop vehicle for a minimum of 20 seconds with transmission gear selector in Drive. Repeat procedure 5 times. Always complete the procedure before returning the vehicle to the customer.
×