Question about Dodge Cars & Trucks

1 Answer

TORQUE VALUE FOR VALVE COVER FOR 2004 4.7L DODGE

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Dodge Master
  • 2,277 Answers

105 in-lbs

Posted on Sep 14, 2019

Ad

6 Suggested Answers

6ya6ya

6ya staff

  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Anonymous

  • 16 Answers

SOURCE: valve cover torque

17 ft lbs

Posted on Jan 23, 2009

sitruc2000

  • 46 Answers

SOURCE: 2000 VW jetta; what is the torque for valve cover and plenum

I briefly looked online and did not see any info direct6ly relating to the torque spec of the cover bolts. I would guess around 15 ft lbs.--not too much--the head is aluminium--best way to go is to walk up to the service counter of the VW dealer and ask him to provide that information. You have the car and they built it!

Posted on Apr 09, 2009

emissionwiz

Marvin

  • 85222 Answers

SOURCE: 2001 jaguar S type v 6. I need to replace the Valve cover gasket.

Felpro brand gaskets are the best in the world, not sure about the intake, if it is in the way then yes remove it.

Posted on Sep 29, 2009

Anonymous

  • 52 Answers

SOURCE: Torque Spec

78 inch pounds

Posted on Nov 21, 2009

Joe Hogan

  • 10865 Answers

SOURCE: valve cover torque

The spec for the valve cover fasteners is 10 nm (about 7.2 ft/lbs) and the sequence of tightening is diagonally from inside to outside. Joe

please rate my answer as very helpful. thanks

Posted on Apr 02, 2010

Testimonial: "Thank you very much!"

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Torque specificacion for dodge dart rally 1.4 turbo 2013


Torque spec's for what hardware on the 2013 Dodge Dart Rally 1.4 Turbo? Headbolts? Main bearing caps? Rod bearing caps? Camshaft drive hardware? Valve covers? Oil pan? What?

Apr 24, 2017 | Dodge Cars & Trucks

1 Answer

Hey there I need the exhaust and Intake(valve) clearance for a komatsu 300-6 please


note Perform the valve clearance check and adjustment at the engine cold state. 1.Remove all of the ignition coils. 2.Remove the cylinder head cover.
caution Turn the crankshaft always clockwise. 3.Turn the crankshaft clockwise, and align the timing mark on the exhaust camshaft sprocket against the upper face of the cylinder head as shown in Figure. Therefore, No.1 cylinder goes to the compression top dead center. 4.Using a thickness gauge, measure the valve clearance with the arrow shown in Figure. If deviated from the standard value, make note for the valve clearance.
Standard value:

    Intake valve 0.20 ± 0.03 mm (0.008 ± 0.0012 inch)
    Exhaust valve 0.30 ± 0.03 mm (0.012 ± 0.0012 inch)
5.Turn the crankshaft clockwise 360 degrees, and put the timing mark on the exhaust camshaft sprocket in position shown in Figure. Therefore, No. 4 cylinder goes to the compression top dead center. 6.Check the valve clearance with the arrow shown in Figure. In the same procedure as 4.
7.If the valve clearance is deviated from the standard value, remove the camshaft and the valve tappet. For the camshaft removal, refer to Camshaft Removal and Installation . 8.Using a micrometer, measure the thickness of the removed valve tappet. 9.Calculate the thickness of the newly installed valve tappet through the following equation.
A: thickness of newly installed valve tappet
B: thickness of removed valve tappet
C: measured valve clearance
Equation

    Intake valve: A = B + [C - 0.20 mm (0.008 inch)]
    Exhaust valve: A = B + [C - 0.30 mm (0.012 inch)] note The valve tappet ranges 3,000 - 3,690 mm (0.1181 - 0.1453 inch) and has 47 types per 0.015 mm (0.0006 inch). The thickness below a decimal point is stamped on the reverse side of the valve tappet. 10.Install the valve tappet selected through the procedure 9, and put the camshaft in position. For the camshaft installation, refer to Camshaft Removal and Installation .
    11.After installing the timing chain, measure the valve clearance using the procedure 3 to 6. Confirm the clearance is within the standard value.
    caution Completely remove all the old FIPG, which might be remaining among the components. 12.After completely removing the liquid gasket adhering on the timing chain case, cylinder block and cylinder head, degrease them with white gasoline.
    caution The cylinder head cover should be installed within 3 minutes of applying liquid gasket.
13.Apply a 4 mm bead of liquid gasket as illustrated.
Specified sealant:
    THREE BOND 1217G or equivalent
14. Install the cylinder head cover and tighten the tightening bolts using the following procedures.
(1) Temporarily tighten to the following torque in order shown in the illustration.
Tightening torque: 3.0 ± 1.0 N·m (27 ± 8 in-lb)(2) Tighten to the specified torque in order shown in the illustration.
Specified torque: 5.5 ± 0.5 N·m (49 ± 4 in-lb)15.Install the ignition coils.

Jan 23, 2017 | Cars & Trucks

1 Answer

What are the torque specifications for a valve cover 2002 3.3ltr dodge caravan


you dont torque a valve cover,hand tight or you crush the gasket

Jul 25, 2015 | Dodge Cars & Trucks

2 Answers

I need to know how to tighten valve cover bolts on 97 dodge stratus


Welcome to FixYa.com What engine do you have?
Thank you for Using FixYa.com Kind Regards, Lee Your FixYa Expert and Master Technician
leedavidian_183.png

Feb 12, 2011 | 1997 Dodge Stratus

1 Answer

Torque spec for valve cover


TORQUE ON VALVE COVERS ARE NOT THAT MUCH. GO ONLINE FOR RESEARCH. IF YOU WANT A GENERAL ANSWER, TIGHTEN TO SEAT CAP OVER GASKET, THEN NO MORE THAN ANOTHER QUARTER TURN ON EACH BOLT. DO NOT "CRANK" IT DOWN AS YOU WILL SPLAY THE GASKET AND CAUSE OIL LEAKS.

Apr 11, 2010 | 2002 Dodge Stratus

2 Answers

Are they valve cover torque values and/or pattern in a 2001 chevy cavalier 2.2l


15 foot pounds... no pattern is given for such a low torque value

Apr 04, 2010 | 2001 Chevrolet Cavalier

2 Answers

2001 jaguar S type v 6. I need to replace the valve cover gasket. Does any one have the torque sequence and torque values for the bolts?


Felpro brand gaskets are the best in the world, not sure about the intake, if it is in the way then yes remove it.

Sep 29, 2009 | 2002 Jaguar S-Type

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

55 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

Marvin
Marvin

Level 3 Expert

85222 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22485 Answers

Jonah Oneal

Level 3 Expert

14092 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...