Question about Land Rover Cars & Trucks

Open Question

Fuel pump delivery module probing giving unusual results

I have a 2007 Land Rover LR2/ Freelander 2 i6. The car is stalling and has no power, mechanic seems to think I need to buy a new fuel pump. Before buying one, I thought it would be a good idea to do some testing to eliminate wiring and electrics. So here's where I'm stuck now: - On the Fuel pump control module itself, I get 12+ volts on the pwr input from the relay, I have a good ground against batt -ve coming into the unit, I have a good steady 12+ volts output to the fuel pump, then I have a 'dynamic -ve outputting to the fuel pump. The fifth terminal is dancing around 5V coming from the ECM. -I call the -ve dynamic because it is dancing, at around the same voltage as the ECM signal measured against Ground, +ve feed to pump, -ve batt terminal as well as +ve batt terminal. -Is this the normal operation of the module? -Are these the proper ranges of voltages for these units?

Posted by on

Ad

2 Suggested Answers

6ya6ya

6ya staff

  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad
johnjnail

john nail

  • 1702 Answers

SOURCE: Fuel pump relay will not

if you ground the tan/light green wire at the relay or at the EEC IV self test conector will the pump run then? and if the pump runs will the engine start?

Posted on Sep 02, 2011

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2002 land rover freelander water pump replacement process?


Landrover Freelander II Timing Belt & Water Pump Replacement ...

? 30:01
https://www.youtube.com/watch?v=4uPBeGGM26M
Oct 21, 2015 - Uploaded by Nabrach
How to fit a new timing belt and water pump on a Landrover Freelander II 2.2 Diesel.

Freelander v6 kv6 water pump - YouTube

? 1:29
https://www.youtube.com/watch?v=sOSbLuZiQbw
Aug 31, 2015 - Uploaded by Gilson Filho
Land Rover Freelander 2002-2005 KV6 Timming belt and replacing valves - Video 1 - Duration: 7:20. Jaime ...

Land Rover Freelander Water Pump Replacement Cost Estimate

https://repairpal.com > Estimator > Land Rover > Freelander A Land Rover Freelander Water Pump Replacement costs between $771 and $922 on average. Get a free detailed estimate for a repair in your area.

How To Replace Water Pump On Land Rover - Atlantic British

? 9:14
www.roverparts.com > ENGINE > Cooling/Heating Apr 2, 2014
See how you can replace the water pump on your Discovery Series II and other Land Rover vehicles ...

2002 land rover freelander water pump replacement Google Search

May 08, 2018 | Land Rover Cars & Trucks

1 Answer

I had fuel filter and pump replace on my 2003 land rover freelander it cranks but wont start


If diesel u have air trapped in system or air leak just give it a tow round the block till she starts .when stated keep foot half way down to bleed system for about 1 min all done

Sep 20, 2013 | 2003 Land Rover Freelander

1 Answer

2004 freelander fuel filter


The fuel filter in your 2004 Landrover Freelander is located inside the fuel pump module assembly. You must remove the fuel pump module from the vehicle and disassemble the fuel pump module to replace the filter. The fuel pump module is accessable by moving your rear seat and pulling the loadspace carpet back to get to the fuel pump access panel.

For more information on this (including diagrams) I would recommend subscribing to the service information for your vehicle for a small anual fee at alldatadiy,com

Jun 16, 2012 | 2004 Land Rover FreeLander

1 Answer

How to replace LR2 Third Brake Light


The Freelander is Land Rover's entry-level crossover SUV. Unlike other Land Rover vehicles that use a traditional "truck," body-on-frame chassis, the Freelander is built on a unibody, front-wheel drive car chassis. The Freelander is sometimes known in the U.S. as the "LR2."

1 Purchase replacement bulb P21/5W, available at most auto parts stores and at any Land Rover
dealer.

2 Turn off engine and open rear cargo door.

3 Remove the two Torx screws from the side of the tail light assembly. Carefully pull the assembly
away and unplug the electrical harness.

4 Turn the assembly over to access the bulb modules. There are three separate bulb modules; the
top module should be the brake light.

5 Rotate the bulb module counterclockwise to release it from the tail light assembly. Push the bulb
down (into the module) and turn it counterclockwise to remove it from the module.

6 Insert the new bulb into the bulb module. Carefully push the bulb down and turn it clockwise.
Reinsert the bulb module into the tail light assembly and turn it clockwise.

7 Reconnect the electrical harness to the tail light assembly. Remount the tail light assembly and
replace the Torx screws.


Dec 26, 2010 | Land Rover LR2

1 Answer

Poor idle and stalling td4 freelander


verify for intake manifold leaks, spark plugs, flow meter. do an ecu scan!!

Jun 01, 2010 | 2003 Land Rover Freelander

1 Answer

Can the a freelander 2 model 2007 play dvd's from


no it wont but if you buy a mp3 player adaptor(fm)you can transfer all your discs onto the memory so as not to carry $100s worth of discs around.......and you can play them in any car,even your mothers.....

May 13, 2010 | 2007 Land Rover LR2

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

26 people viewed this question

Ask a Question

Usually answered in minutes!

Top Land Rover Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22485 Answers

Marvin
Marvin

Level 3 Expert

85216 Answers

Jonah Oneal

Level 3 Expert

14092 Answers

Are you a Land Rover Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...